Instruction/ maintenance manual of the product DD24S Fisher & Paykel
Go to page of 8
DishDra wer® Installation instructions US CA Impor tant! SA VE THESE INSTR UCTIONS The models shown in this document may not be available in all mark ets and are subject to change at any time. F or current detail s about model and specification availability in your c ountry, please go to our website www.
Minimum clearances (inches (mm)) ⁄ ” ( 2.5 mm) ⁄ ” ( 2.5 mm) ½ ” ( 13 mm) 23 PRODUC T DIMENSIONS CABINE TR Y DIMENSIONS A B C E D F G H J K Product dimensions (inches (mm)) Pre.
P ARTS SUPPLIED Clamp (1) Wire clip (1) Phillips 16 mm screws (7) T op mounting brackets (2) Drain hose support (1) Moisture protection tape (1) (to prevent moisture damage) Drain hose joiner (1) Washer (1) Edge Pr otector (1) (if service hole partition is metal) 4 2” x 4” Note: Ser vices can be located either side of DishDrawer®.
3 4 5 6 7 7 8 8 1 30 mm 2 1 2 1 13 17 14 15 15 16 9 12 11 11 10 A Ensure the draw er is removed and then rotated count er- clockwise to prevent kinked hoses. Before r efitting the drawer , ensure the hoses are not twisted and the latches at the rear of each draw er runner are facing for ward.
ROUTE THE HOSES AND MOVE INT O THE CA VITY 7 8 REMOVE THE DRA WER AND SECURE THE PRODUC T 1 2 Tie together to a void kinking. A The product has three pairs of mounting brackets: a pair of optional brackets on the top ( C ) and two pairs of formed brackets in the side of the chassis ( A , B ).
9 REFIT THE DRA WER 2 1 4 5 4 3 Before r efitting the drawer , ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing for ward. Ensure the drawer clips on both sides are reset. Ensure the drawer is now rotated clockwise back.
29 ½” - 34 ¾” (750 - 882.5 mm) 1 ½” (38 mm) max. 4 ¾” (120 mm) 2 1 4 1 6 5 4 7 2 29 ½” - 34 ¾” (750 - 882.5 mm) 3 1 4 3 2 5 5 4 3 6 A If space is limited for fixing, push hose through drain hose support to required height DishDraw er® with W aste Disposal 29 ½ ” - 34 ¾ ” ( 750 - 882.
12 11 FINAL CHECKLIST TROUBLESHOO TING Check all parts are installed. Ensure product is level , securely fastened to the cabinetry and opens and closes freely .
An important point after buying a device Fisher & Paykel DD24S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher & Paykel DD24S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher & Paykel DD24S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher & Paykel DD24S you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher & Paykel DD24S will certainly help you make a decision on the purchase.
If you already are a holder of Fisher & Paykel DD24S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher & Paykel DD24S.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher & Paykel DD24S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher & Paykel DD24S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
