Instruction/ maintenance manual of the product RNS5 Alloy Computer Products
Go to page of 22
Alloy RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch User’s Manual Rev.1.1 20-Jan-2005.
Content Introduction ......................................................... 1 Features ................................................................... 1 Package Checklist .................................................... 2 Hardware Description .
Introduction Industrial environments are usually more demanding than office environments. Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment.
Package Checklist Alloy RNS5/8 Industrial 5-port/8-port Et hernet Rail Switches are packaged with the following items: RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch One DIN-Rail clip (a.
Hardware Description D i m e n s i o n s RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch dimensions (W x H x D) are 54mm x 135mm x 105mm F r o n t P a n e l The Front Panel of the RNS 5 Industrial 5-port Ethernet Rail Switch is shown in Figure A.
The Front Panel of the RNS 8 Industrial 8-port Ethernet Rail Switch is shown in Figure A. LED Indicators UTP Ports Figure A. Front Panel of the RNS8 In dustrial 8-port Ethernet Rail Switch 4.
Bottom View The bottom view of the RNS5/8 Industr ial 5-port/8-port Et hernet Rail Switch consists of one terminal block connector with two DC power inputs, Alarm output and one DC IN power jack for an additional AC/DC power adapter.
L E D I n d i c a t o r s There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of the RNS5 Industrial Ethernet Rail Switch. These LED indicators provide administrators with real-time system stat us. Table 1 gives descriptions of the functions of each LED indicator.
Port LED Status Description Orange The port is operating in full-duplex mode. Blinking orange Collision of Packets occurring. Off The port is in half-duplex mode or no device is attached. Green A network device is detected. Blinking green The port is transmitting or receiving packets from the TX device.
Blinks The port is transmitting or receiving packets from the TX device. Off No device is attached. Orange The port is operating in full-duplex mode. Blinks Collision of packets occurs. FDX/COL of Port 7/8 Off The port is in half-duplex mode or no device is attached.
Fig C Straight Through Cabling Schematic Fig C-1 Cross Over Cabling Schematic All ports of RNS5/8 support the auto-MD I/MDI-X function. When you use an Ethernet cable to connect other devices, such as computers, swit ches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45 c onnector are used to communicate with the connected devices.
Mounting Installation DIN-Rail Mounting The DIN-Rail clip is already attached to the RNS5/8 when packaged. If the DIN-Rail clip is not screwed on the RNS5/8, follow the instructions and the figure below to attach the DIN-Rail clip to the RNS5/8. Rear Panel of the RNS5/8 DIN-Rail Clip 1.
Follow the steps below to mount t he RNS5/8 to the DIN-Rail track: 1. First, insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track from its upper side. 2. Lightly push the bottom of the DIN-Rail clip into the track. 3. Check if the DIN-Rail clip is tightly attached on the track.
Wall Mounting Follow the steps below to install the RNS5/8 with the wall mounting plate. 1. To remove the DIN-Rail clip from the RNS5/8, loosen t he screws from the DIN-Rail clip. 2. Place the wall mounting plate on the rear panel of the RNS5/8. 3. Use the screws to tighten the wa ll mounting plate ont o the RNS5/8.
Hardware Installation The following figure illustrates a typi cal application of RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch. Installation and Testing 1. Take your RNS5/8 Industrial 5-port/8- port Rail Switch out of the package box. 2. Check if the DIN-Rail clip is attached to the RNS5/8.
4. Pull the terminal bloc k off the RNS5/8 and wire the power lines . Refer to the Wiring the DC Power Inputs section for how to wire the power inputs.
10. Power on the host, activate the Command Line mode, and ping the connected Ethernet device to see if it will respond. 10.1 To enable the “Command Line mode”, click on Run in the Start menu, type Command , and click on OK to continue. 10.2 Type ping 192.
12. Power on the host, activate the Command Line mode, and ping the connected Ethernet device by typing “ping –t 192.168.1.1” command to see if it will respond. 13. The parameter ”t” allows you to cont inue to ping the network device, as shown in the figure below.
Trouble shooting Make sure you are using the correct VDC power supplies (12 to 48 VDC) or power adapters. Do not use power adapt ers with DC output over 48V. It will damage the device. Select Ethernet cables with specifications suitable for your applications to set up your system.
Technical Specifications Standards IEEE 802.3 10BaseT Ethernet IEEE 802.3u 100BaseT(X) Fast Ethernet IEEE802.3x Flow Control and Back pressure Protocols CSMA/CD Technology Store and Forward Transm.
Power Suppl y 12 to 48 VDC, redundant dual DC power inputs with reverse polarity protection, and a removable terminal block for master and slave VDC power inputs. Power consumption RNS5: 2.8 Watts RNS8: 4.6 Watts Packet throughput ability RNS5: 0.74Mpps @ 64bytes (5TX) RNS8: 1.
IEC60068-2-6 (Vibration) 20.
An important point after buying a device Alloy Computer Products RNS5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alloy Computer Products RNS5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alloy Computer Products RNS5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alloy Computer Products RNS5 you will learn all the available features of the product, as well as information on its operation. The information that you get Alloy Computer Products RNS5 will certainly help you make a decision on the purchase.
If you already are a holder of Alloy Computer Products RNS5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alloy Computer Products RNS5.
However, one of the most important roles played by the user manual is to help in solving problems with Alloy Computer Products RNS5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alloy Computer Products RNS5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
