Instruction/ maintenance manual of the product CG2 Fireboy- Xintex, LTD
Go to page of 18
1 18004 04/03/2007 Rev. C CG2 & MA2 Series Clean Agent FE-241 & HF C-227ea Owner’s Manual & Installation Instructions For all sizes 25 cubic feet to 1500 cubic feet Read and comply with all instructions, warnings and limitations before installing, servicing or removing this device.
2 This owner’s manual and i nstallation instru ctions pamphlet is provided in English. Additional copies in English are availabl e at no charge by contacting the manufacturer, distributor or dealer. Co pies in the language of desti nation are available upon request for an additio nal fee.
3 General Information Fireboy Automatic (CG series) and Manual/Automatic (MA) se ries Fire Extinguishing Systems are manufactured for a broad range of ap plications, including marine, industrial, and comm ercial uses. This booklet is intended to outline the proper installation of the sy stem for mari ne applications; most applications are similar.
4 WARNING: • Never install a Fireboy system on the underside of a h atch cover or on an access door that may open or separate in an expl osion • Never install the actuator of a Fireboy sy stem in close proximity to exhaust manifolds or turbocha rgers.
5 Volume Approximate Protected Diameter Total Height Age nt Weight Shipping Weight Model Number ft^3 m^3 in cm in cm lbs kgs lbs kgs U.S.C.G. # CG2-550-FE241 550 15.6 7.2 18 24.7 63 18.6 8.5 49 22.1 162.029/185/0 CG2-600-FE241 600 17 7.2 18 24.7 63 20.
6 Volume Approximate Protected Diameter Total Height Age nt Weight Shipping Weight Model Number ft^3 m^3 in cm in cm lbs kgs lbs kgs U.S.C.G. # CG2-300-227 300 8.5 7.2 18 15.1 38 13 5.9 35 15.9 162.029/210/0 CG2-325-227 325 9.2 7.2 18 15.1 38 14 6.4 36 16.
7 Marine Installation Instructions Before Installation 1. Check the system for damage during sh ipment. 2. Check the pressure gauge to be sure the gauge pointer lies within the green zone at 70°F (2 1°C). The correct weig ht is shown on the nameplate for the appropriate model.
8 Accommodating Diesel Engines 1. Failure to install an Automa tic Engine Shutdown in any compartment containing a diesel engine and a Fir eboy system impedes the fire extinguisher and may prevent fire extinguishment.
9 WARNING: • An electrical short may result in electrical burn, injury or fire • Before attempting to wire the indicato r lamp, turn off all electrical current to the ignition switch • All Fireb.
10 If the engine compartment is equipped with a powe red ventilation system, U.S. Coast Guard Rule 162.029 requires that the ground conne ction of the ventilation system be connected to the Fireboy system. Failure to connect a po wered ventilation system in the manner described belo w impedes fire extinguisher and may prev ent fire extinguishment.
11 NOTE: Never push the cable at the T-handle end. Cable m ay jam and become inoperable. Fixing a jammed cable: 1. Turn the T-handle and threaded metal rod counter clo ckwise ½ turn until the jam releases . 2. If necessary, use a pair of pliers to carefully twist the threaded metal rod until the jam releases.
12 6. Pull cable to full extension. 7. Screw ferrule on to cable (approximately 4-5 turns maximum). 8. Slide o-ring onto c able shaft. 9. Screw red T-handle onto cable sha ft (Do not obstruct cross hole in T- handle). 10. Push red T-handle into ferrule to seat o-ring.
13 3. Push the cable end through the hole on the cylinder manifold far enough to allow the flexible strand to be bent. 4. Place “S” hook through the hole in the MA lever. 5. Gently pull cable sheath back into manifold, aligning the groove in sheath with slot in the manifold.
14 1. A loud sound similar to small arms fire. 2. A loud sound of rushing air. 3. An extinguished indicator lamp. 4. A stalled engine. When actuation occurs 1. Immediately shutdown all engines, powered ventilation, and electrical systems. 2. Extinguish all smoking materials.
15 Inspect manual discharge cabl e annually when inspe cting the fire extinguisher. 1. Do not remove the pull pin on the T-handle when disconnecting the manual discharge cable fro m the fire extinguisher manifold. 2. Remove the wire retaining clip secu ring the cable located at the sl ot in the top of the manifold.
16 Automatic Engine Shutdown/Override System is required for u se with Fireboy systems in diesel powered cr aft. Returning Fireboy-Xintex Equipment No product may be returned for credit or repair withou t a written “Returned Material Authorization” (RMA) form.
17 NOTE: Detroit Diesel engines may require Auto matic Engine Shutdown system s with time delay. Fireboy accessories are av ailable from y our Fireboy-Xintex distributor, dealer or retailer.
18 3 YEAR LIMITED WARRANTY This Warranty is in lieu of all ot her expressed of implied Wa rranties Seller warrants title, materials, and workmanship on equipment, except components manufactured by others for whic h the Seller assigns, as permitted, the original manufacturer’ s warranty.
An important point after buying a device Fireboy- Xintex, LTD CG2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fireboy- Xintex, LTD CG2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fireboy- Xintex, LTD CG2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fireboy- Xintex, LTD CG2 you will learn all the available features of the product, as well as information on its operation. The information that you get Fireboy- Xintex, LTD CG2 will certainly help you make a decision on the purchase.
If you already are a holder of Fireboy- Xintex, LTD CG2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fireboy- Xintex, LTD CG2.
However, one of the most important roles played by the user manual is to help in solving problems with Fireboy- Xintex, LTD CG2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fireboy- Xintex, LTD CG2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
