Instruction/ maintenance manual of the product TYPE "C" Field Controls
Go to page of 8
CHIMNEY TOP DRAFT INDUCER Model: Type “C” The Type “C” Chimney Top Draft Ind ucer is designed for i nstallation on smoke pipes, Type” B” vents, Ty pe “L” vents and factory built Class “A” chimney s. The Type “C” Draft Inducer is installed on the top of the vent sy stem outside of the building.
Page 2 INSTALLATION S MOKE P IPE , T YPE “B” VENTS AND T YPE ”L” VENTS 1. Insert the Type “C” housing directly into the vent pipe. (See Figu re 1 ) 2. Fasten h ousing to vent pipe using th ree (3) sheet met al screws, located 120º apart. 3.
Page 3 WIRING 1. Remove the four (4) screws that hold the conical rain cover in place. This will expose the motor juction box . CAUTION: Disconn ect electrical powe r when wi ring draft inducer. 2. Wire the draft inducer in accordance wi th the National Electrical Code and applicable lo cal codes.
Page 4 INDUCTEUR DE TIRAGE DE TETE DE CHEMINEE Model: Type “C” INSTALLATION T UYAUX DE CHEMINÉE , ÉVENTS DE TYPE "B" ET ÉVENTS DE TYPE "L" 1. Insérer le boîtier de type "C" directem ent dans le tuyau de ventilation.
Page 5 CÂBLAGE 1. Retirer l es quatre vis qui maintiennent le cap uchon coniqu e en place, de façon à exposer la b oîte de jonction du moteur. ATTENTION: Couper l’ alimentation électrique a vant de câbler l’ inducteur de tirage. 2. Câbler l’inducteur de tirage selon le Code national de l’électricité et les codes locaux applicables.
Page 6 INDUCTOR DE DIRCULACIÓN PARA LA PARTE SUPERIOR DE LA CHIMENEA Modelo: Tipo “C” INSTALACIÓN C ONDUCTOS DE HUMO , RESPIR ADEROS TIPO “B” Y RESPI RADEROS TIPO “L” 1. Introduzca el ba stidor tipo “C” dire ctamente en el tu bo de ventilación.
Page 7 CABLEADO 1. Saque los cuatro (4) tornillos que sostienen el capuchón cónico en posi ción. Esto dejará expuesta la caja d e empalme del motor. PRECAUCIÓN: Desconecte la corriente eléctrica cua ndo conecte los cables del indu ctor de circul aci ón.
Page 8 O PTIONAL R AIN S HIELD I NSTALLATION I NSTRUCTI ONS : As an optional accessory to the Typ e C Draft Inducer, a rain shield has b een provided to further p revent water from wind driven rain from entering the chimney. To install ple ase follow the instructions below.
An important point after buying a device Field Controls TYPE "C" (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Field Controls TYPE "C" yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Field Controls TYPE "C" - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Field Controls TYPE "C" you will learn all the available features of the product, as well as information on its operation. The information that you get Field Controls TYPE "C" will certainly help you make a decision on the purchase.
If you already are a holder of Field Controls TYPE "C", but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Field Controls TYPE "C".
However, one of the most important roles played by the user manual is to help in solving problems with Field Controls TYPE "C". Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Field Controls TYPE "C" along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
