Instruction/ maintenance manual of the product Agio Faber
Go to page of 12
V ersion 10/05 - Page 1 READ THESE INSTRUCTIONS BEFORE YOU ST ART INST ALLING THIS RANGEHOOD W ARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.
V ersion 10/05 - Page 2 VENTING REQUIREMENTS Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof. The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance.
V ersion 10/05 - Page 3 RÈGLEMENTS D'ÉV ACUA TION Confirmer la sortie d'évacuation - soit par le mur , soit par le toit. Uti lise z une long ueur de tuy auter ie mini male ave c les moind res de coudes pour la plus grande efficacité. Le diamètre de tuyauterie doit être uniforme.
V ersion 10/05 - Page 4 TOOLS NEEDED FOR INST ALLA TION • Saber Saw or Jig Saw • Drill • 1 1/4" Wood Drill Bit • Pliers • Phillips Screwdriver • Flat Blade Screwdriver • Wire Stripp.
V ersion 10/05 - Page 5 PREP ARE THE CABINET 1. Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.
V ersion 10/05 - Page 6 6. Reattach the control box and support. Make sure that the wiring harness is concealed behind the support. 7. Remove the field wiring compartment cover .
V ersion 10/05 - Page 7 Three Screws Rangehood Body Front Strip CUSTOMIZING YOUR RANGEHOOD The front strip of the rangehood can be customized by replac- ing the factory supplied strip with a custom front strip made from the same materials as your cabinets.
V ersion 10/05 - Page 8 CONDUIT HORIZONT AL CONDUIT VERTICAL FIGURE 4 Coude 45˚ Coude 90˚ Coude plat 90˚ Capuchon de mur 3,0 pi 5,0 pi 12,0 pi 0,0 pi 9 pi de conduit droit 2 Coudes 90˚ Capuchon de.
V ersion 10/05 - Page 9 1. Débrancher et déplacer la cuisinière de lʼouverture afin dʼavoir un meilleur accès aux armoires supérieures et au mur arrière. Placer un recouvrement épais sur la plaque de cuisson, la cuisinière encastrée ou le dessus du comptoir pour protéger des dommages et de la poussière.
V ersion 10/05 - Page 10 6. Réinstaller la boîte de contrôle et le support. Sʼassurer que le fil conducteur soit caché derrière le support. 7. Retirer le couvercle du compartiment de filage. Passer le câble dʼalimentation par la pastille enfonçable de la boîte électrique.
V ersion 10/05 - Page 1 1 V ue latérale de la hotte FIGURE 16 DIAGRAMME DE FILAGE • Cette hotte utilise une ampoule fluorescente, type F33- 15W-T8 et un déclencheur , type S2. PERSONNALISER LA HOTTE La bande frontale de la hotte peut être personnalisée en remplaçant la bande fournie par une bande de même matière que lʼarmoire.
4324281.
An important point after buying a device Faber Agio (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Faber Agio yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Faber Agio - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Faber Agio you will learn all the available features of the product, as well as information on its operation. The information that you get Faber Agio will certainly help you make a decision on the purchase.
If you already are a holder of Faber Agio, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Faber Agio.
However, one of the most important roles played by the user manual is to help in solving problems with Faber Agio. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Faber Agio along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
