Instruction/ maintenance manual of the product USFM 100 Extron electronic
Go to page of 8
1 The Extron USFM 100 is a mounting kit for suspending ultra short throw projectors from a wall. The USFM 100 base plate enclosure is capable of mounting a PoleV ault ® System switcher and its supplied power supply , with sufficient room remaining for installing additional devices and cable management.
2 Installation WARNING : Before commencing installation, the wall structure must be examined to determine if it is suitable for the proper installation and support of this product. If needed, the installer should reinforce the wall. Drywalls should have a minimum thickness of 1/2 inch and a maximum thickness of 5/8 inch .
3 For drywall with wood studs i. Drill ¼ inch pilot holes at the marked stud locations. ii. Align the base plate mounting holes over the pilot holes and lightly secure with 5/16 inch lag screws and washers. NOTE: If using toggle screws for assembly , follow the installation method (steps A-D ) shown in figure 3.
4 3. Run Cables NOTE: All cable installation should be performed in accordance with local and national building codes, fire and safety codes, and local and national electrical codes. Run signal cables from the PoleV ault input wallplates, control device location, and the speakers to the USFM 100 location.
5 5. Attach the Boom Arm, Power Supply , and Projector a. Hook the boom arm over the top rail on the base plate so that the tab on the arm (see figure 6, inset) is against the rail. Secure the arm at the bottom with the two supplied (10-32 x 3/8 inch) pan head screws and washers, and at the top with the single ¼-28 x ¾ inch hex screw .
6 6. Complete the Installation a. Switch on the display device, control device, and signal sources, and configure the system. Adjust the position and length of the boom arm as needed, adjusting the UPB 25 to center the image. When fully satisfied, secure the arm and tighten down all the UPB 25 locking screws.
7 34.40" (87.38 cm) 2.20" (5.59 cm) 31.80" (80.77 cm) 3.60" (9.14 cm) 3.85" (9.77 cm) 11.82" (30.02 cm) 1.25" (3.18 cm) Base Plate (front view) Boom Arm (side view) Boom Arm (top view) 21.65" (54.99 cm) 12.50" (min.
8 USFM 100 Installation Guide, cont'd 68-1838-01 Rev B 05 11 31.80" (max) (80.77 cm) 30.00" (max) (76.20 cm) 3.71" (9.42 cm) 3.22” - 5.22" (8.18 - 13.26 cm) 4.42” - 6.42" (11.23 - 16.31 cm) Center of UPB 0.0” - 2.0" (0 - 5.
An important point after buying a device Extron electronic USFM 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic USFM 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic USFM 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic USFM 100 you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic USFM 100 will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic USFM 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic USFM 100.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic USFM 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic USFM 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
