Instruction/ maintenance manual of the product TLP 700TV Extron electronic
Go to page of 58
68-1378-01 Rev. B 10 10 TLP 700MV and TLP 700TV User Guide TouchLink™ TouchLink Touchpanel Control Systems.
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product enclosure that may present a risk of electric shock.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
.
Contents Introduction ............................................ 1 About the TLP 700MV and TLP 700TV ............. 1 Features ........................................................... 2 Requirements ................................................
TLP 700MV and TLP 700TV • Contents vi.
Intr oduction This guide describes the function, installation and operation of the T ouchLink TLP 700MV and TLP 700TV panels. The guide also provides information about optional accessories that are available fr om Extron for both panels. Unless otherwise stated, the terms “TLP 700 series” and “TLP 700” refer to both models.
100-240V 50-60Hz I N P U T VID VID YC Y B-Y R-Y RGB DVI 8 1 2 4 5 3 L 2 1 3 4 5 6 7 R AUDIO INPUT L A B RS-232 R OUTPUT L R OUTPUT RGB Y, B-Y, R-Y 8 7 RGB 6 LISTED 1T23 I.
Multiple mounting options — The TLP 700MV can be wall-mounted, rack-mounted, or furniture-mounted. The TLP 700TV comes with a stand that allows it to be placed on a desktop. If the stand is removed, the unit can be VESA-mounted on a wall or furniture using either of the optional Extron kits.
Panel Featur es This section describes: TLP 700MV Front Panel Featur es and Operations TLP 700MV Rear Panel Features and Connections TLP 700TV Front Panel Featur es and Operations TLP 700TV Rear Panel.
There ar e three buttons recessed behind the bezel. These buttons ar e used to configure the unit and reset parameters to factory defaults: LIGHTS ON DISPLA Y MUTE AUDIO MUTE SPEECH MUTE AU TO IMAGE FREEZE LIGHTS OFF SCREEN SCREEN HELP ? 7 8 9 10 Figure 3.
TLP 700MV Rear Panel Featur es and Connections 11 12 13 Figure 4. TLP 700MV Rear Panel Featur es k Power Connector — Connect the two pole, 3.5 mm captive screw connector fr om the provided power supply to the power supply socket on the r ear panel. Ensure the connections have the correct polarity as shown below: 12V 0.
NOTES: The length of the exposed wires in the stripping process is critical. The ideal length is 3/16 inches (5 mm). Any longer and the exposed wires may touch, causing a short circuit between them. Any shorter and the wir es can be easily pulled out even if tightly fastened by the captive screws.
TLP 700TV Fr ont Panel Features and Operations 1 4 5 6 2 3 7 8 9 Figure 6. TLP 700TV Fr ont Panel Features a Buttons — These ten backlit push-buttons (five on either side of the screen) can be configured to execute user -defined functions using the Extron Global Congurator software (page 25).
TLP 700TV Rear Panel Featur es and Connections With Stand Attached 10 13 11 12 Figure 7. TLP 700TV Rear Featur es The following connections are available thr ough the back panel when the stand is in place: j LED lights — The Link LED lights green to indicate a good network connection.
TLP 700TV Base Featur es 17 C Gain Vid / Y Gain Sharp 33-1814-01 A 19 18 Figure 8. TLP 700TV Base Featur es The TLP 700TV stand, which can be removed for VESA mounting, has: q Three adjustable potentiometers — These ar e used to control sharpness and gain for both S-video luminance (Y) and S-video chrominance (C).
Initial Calibration This section describes: How to Access the Internal On-screen Menus The Main , V olume , Time , Network , and Video Screens The Screen T ouch Calibration Scr.
When Auto Backlight is set to Off, the Backlight option allows the backlighting to be set manually from 0 to 100%. Pr ess the Down or Up buttons to highlight the Backlight options and use the volume control knob or pr ess the Down or Up buttons to adjust the backlighting.
Time Scr een Click on the Down or Up buttons to highlight one of the adjustable time settings. Use the Down and Up buttons or the volume control knob to adjust the Month, Day , Y ear , Hours, and Minutes. NOTE: The Hours value uses the 24 hour clock. For 10 am, set Hours to 10; for 10 pm, set Hours to 22.
V ideo Screen The small gray rectangle pr ovides a video preview window that allows the user to adjust the video properties. Click on the Down or Up buttons to highlight one of the adjustable video settings.
Contr ol Softwar e This section of the guide discusses the software and firmwar e needed to set up the T ouchpanel units: Software Overview Installing the Software Updating th.
Installing the Softwar e Installation from the Extr on Disc Insert the disc provided into the DVD-ROM drive of the computer . If the setup pr ogram does not start automatically , run Launch.exe from the DVD-ROM dir ectory in W indows My Computer . Select the Software tab, locate the GUI Configurator program and click Install .
Updating the Firmwar e Firmware for the TLP 700 can be upgraded using the Extr on Firmware Loader or using your web browser . Befor e starting, consult your IT team and ensure that the TLP 700 has a unique IP address.
Updating Firmware Fr om a Web Br owser NOTES: Y our PC must have inter net access and be on the same network as the T ouchLink Panel. 1. On the Extron web site, select the Download tab and click on the Firmware option in the menu bar at the left of the screen (see Figur e 10 on page 16).
Using the T ouchLink Panel W eb Pages As seen in the previous section , the TLP 700MV and TLP 700TV T ouchLink Panels have default web pages that can be used to read and change the curr ent settings of the panels. The web pages can be accessed as follows: 1.
3. Selecting the Passwords page allows the user to set passwords for an Administrator and a User . T o set a password, follow the instructions at the top of the page. Figure 14. TLP 700 Conguration T ab: Passwor ds Page 4. T o upgrade the unit firmwar e, select Firmware Upgrade and follow the instructions on page 18 .
Using GUI Configurator This section provides an overview of the GUI Configurator pr ogram. For complete information about the program, consult the GUI Configurator help file (click on Contents in the Help menu or press the <F1> key while within the pr ogram).
2. Y ou can choose to: Start a New Project — Clicking OK opens a dialog box that of fers a choice of project options. Figure 18. GUI Congurator New Project Dialog Box A series of icons offer you the choice of cr eating a project with a template or without a template and allow you to select the size and type of T ouchlink Panel.
Download an Existing Project fr om a Panel — Clicking OK opens a dialog box that allows you to download a file that has been uploaded to a panel.
3. Depending on which option was selected in step 2 , GUI Configurator opens to a new or an existing project. The initial scr een is divided into a series of panes offering a range of tools that can be used to design or modify the project.
b. The Panel Manager dialog box opens: Figure 23. Add a T ouchLink panel (b) c. Click on the Add Panel icon to add a new panel to the list in the left pane. d. Highlight the name of the panel in the left pane to display the properties of that panel in the right pane.
Using Global Congurator NOTE: T o configur e a T ouchLink Panel, you must use Global Configurator version 3.0 or later . This section provides an overview of the Global Configurator pr ogram.
2. Select Create A New Project and click OK . The dialog box closes, leaving the Project Settings scr een. Figure 25. Global Congurator Project Settings 3. Enter the IP Address for the TLP 700MV panel. The default T elnet connection is port 23 and HTTP is port 80, so these values do not usually need to be changed.
4. Click OK and the Project Settings scr een closes and is replaced by the Add Device dialog box: Figure 26. Global Congurator Add Device Dialog Box T o see all the options, click on the Advanced >>> button. The button name changes to Basic <<< (as shown in the figure above).
5. Click OK and the Add Device screen closes. The start-up scr een, which was behind it, is now visible. The device configuration tree, in the panel to the left of the main screen, shows the IPL 250 and the available ports: Figure 27. Conguring an IP Link Device 6.
7. The Add T ouchPanel dialog box opens. a. Ensure the corr ect model is selected from the drop-down menu. b. Enter the IP address for the T ouchLink Panel. c. Set the T elnet Port (usually 23). d. If necessary enter the password. e. Select the Import/Apply Layout check box.
Specications TLP 700MV Display Screen type .................................... Active matrix TFT color display Size ................................................ 7" (17.8 cm), measured diagonally Resolution ................................
Audio output Speaker output .............................. 1 mono, 86 dB SPL, 0.1 watt, 0.1 m, half space Frequency r esponse ........................ 400 Hz to 15 kHz, ±5 dB Playback format(s) .......................... WA V files: 8 bit PCM, mono, 8 kHz sampling General External power supply .
W arranty ........................................ 3 years parts and labor; touchscreen display and overlay components are cover ed for 1 year NOTES: All nominal levels are at ±10%.
Specications TLP 700TV Display Screen type .................................... Active matrix TFT color display Size ................................................ 7" (17.8 cm), measured diagonally Resolution ................................
Audio input — see S-video or composite video MTP transmitters' specications NOTE: Audio input is available only from an Extr on MTP transmitter through the RJ-45 connector in the base of the unit. If the base is removed fr om the TLP 700TV , connections are via BNC connectors, and there is no audio input.
75° Min Tilt 30° Max Tilt 9.41" (23.90 cm) 7.68" (19.51 cm) FRONT VIEW SIDE VIEW BOTT OM VIEW TLP 700 TV 8.16" (20.72 cm) 7.88" (20.01 cm) Extron 6.50" (16.51 cm) 8.89" (22.59 cm) 7.47" (18.97 cm) 0.70" (1.78 cm) 5.
Accessories and Part Numbers Included Parts Description Part Number TLP 700MV T ouchLink Panel (wall mount) 60-546-0x TLP 700TV T ouchLink Panel (desktop or VESA mount) 60-548-02 12 VDC, 1A power supp.
Mounting This section outlines the various options for: Rack Mounting the TLP 700MV W all Mounting the TLP 700MV W all Mounting the TLP 700MV with a Wallbox Desktop Mou.
W all Mounting the TLP 700MV The TLP 700MV can be mounted in the wall or through furniture. Extr on recommends using the Extron TR 700M trim ring to conceal any ragged edges when the hole is cut in the wall or furniture. T o mount the TLP 700MV dir ectly into a wall, follow these steps.
Tr im Ring Screws (4) Tighten screws to rotate locking arms. Be ze l snaps to unit (4 plcs ea side). Figure 31. Secure the TLP 700MV to a W all With Locking Arms 11. If required, perform the initial calibration (see page 11). 12. Replace the bezel by pressing the catches on the bezel into the corresponding holes on the front of the panel.
Desktop Mounting the TLP 700TV The TLP 700TV comes assembled with a stand that allows it to be placed on a desktop. If requir ed, the stand can be removed and replaced with the Extr on VM 700T kit (part number 70-692-01 ). This kit fits into any third-party VESA T ype D 75 mm wall mount system.
T o pr epare the TLP 700TV for wall mounting, using either kit, follow these instructions: 1. Remove the TLP 700TV from its packaging or , if the TLP 700TV has pr eviously been used as a free-standing, desktop unit, r emove all cables to the back of the base.
4. Remove the back cover to reveal the metal stand and the cables connecting the cir cuit board in the base to the touchpanel scr een. 4 Figure 41. Remove Back Cover . 5. Cut the plastic tie holding the cables to the metal stand. 6. Disconnect the power , LAN, audio, LED, and two BNC cables from the cir cuit board in the base.
9. Thread the cables thr ough the gap between the top bracket and the stand. Place the screen, face down, on a soft cloth. 9 Figure 44. Thread Cables into Place. 10. Remove and save the three Phillips head screws holding the plastic molding to the back of the screen.
11. Disconnect the audio, LED, and power cables from the back panel of the screen. The audio cables are the black and white pair , wound ar ound a ferrite core. The power cables are the r ed and black pair , terminated with a blue, 2-pole captive screw connector .
Reset Modes The TLP 700MV and TLP 700TV have four reset modes that corr espond to four of the five reset modes for the IP Link contr ollers. The modes are initiated by pressing the Reset button. T o access the Reset button on the TLP 700MV , r emove the bezel.
Button Labels This section provides information about: Button Label Software Replacing Button Labels Button Label Softwar e Installing or Replacing Button Labels Printed labels are included with the TLP 700MV and TLP 700TV .
Using the Button-Label Generator software 1. T o run the Button-Label Generator pr ogram, click on the desktop icon. Alter natively , click Start > Programs > Extron Electronics > Button Label Generator > Button Label Generator . The Button-Label Generator window appears: Figure 47.
Replacing Button Labels The illustration below shows how to replace the button labels on the TLP 700MV . Although, the buttons on the TLP 700TV are slightly smaller and the labels ar e different dimensions, the procedur e for replacing labels on either model is the same.
TLP 700MV and TLP 700TV • Button Labels 50.
Extr on ® W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years fr om the date of purchase; touchscreen display and overlay components ar e covered for 1 year .
Extron USA - West Headquarters + 800.633.9876 Inside USA/Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East +800.633.9876 Inside USA/Canada Only +1.919.863.1794 +1.919.863.1797 FAX Extron Europe +800.3987.6673 Inside Europe Only +31.33.
An important point after buying a device Extron electronic TLP 700TV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic TLP 700TV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic TLP 700TV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic TLP 700TV you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic TLP 700TV will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic TLP 700TV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic TLP 700TV.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic TLP 700TV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic TLP 700TV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center