Instruction/ maintenance manual of the product SI 3 Extron electronic
Go to page of 16
User’s Guide Compact Full Range Surface Mount Speakers 68-1261-01 Rev . A 11 07 SI 3 System INTEGRA TOR ™.
SI 3 Speakers • Packaging Packaging Information Figure 1 — SI 3 speaker packaging details P a r t N o . X X X -X X X - 01 Install 206W Ce i li n g Spe aker 3 3 -X X X X - 0 1 R E V .
Intr oduction SI 3 Speakers • Introduction 1 About the SI 3 Speakers The Extron System INTEGRA TOR ™ SI 3 full range, compact, surface mount speaker is ideally suited for classrooms, conference r ooms, and boardr ooms.
SI 3 Speakers • Features 2 Featur es Dimensions : 8.75" H x 5.75" W x 5.61" D (22.2 cm H x 14.6 cm W x 14.24 cm D) a Bass reflex port b Front locking access (allows for speaker posit.
Installation 3 SI 3 Speakers • Installation Installing the SI 3 Speakers The Extron SI 3 speakers can be mounted on a surface, such as a wall or post, or mounted in a bookcase, or on a shelf, and can be used with any Extron pr oduct supporting audio.
4 SI 3 Speakers • Installation Installation, cont’d W all mounting applications Installing the wall mount assembly N Before starting installation, ensur e that the wall and wall material are capable of supporting the combined weight of the speakers and the wall mount assemblies.
4. Mark the wall where the wir e will pass through the plate, and cut a small access hole large enough for the wir e to pass through without interfer ence. Where the stud is wider than the plate's access hole, cut the hole in the wall to the left or right and directly alongside the stud (see figure 7).
Installation, cont’d 6 SI 3 Speakers • Installation 6 . Pull sufficient wir e up through the holes in the r ear plate (see figure 8) to allow ease of connection to the speaker after installation. N Do not strip and connect the wire at this time. P ass the wires through the plate access hole.
Installation, cont’d 6 SI 3 Speakers • Installation 6 . Pull sufficient wir e up through the holes in the r ear plate (see figure 8) to allow ease of connection to the speaker after installation. N Do not strip and connect the wire at this time. P ass the wires through the plate access hole.
8 SI 3 Speakers • Installation Installation, cont’d Wiring the speakers 1. When both speakers are in place, carefully pull enough speaker wir e to reach to the terminals at the back of the each speaker and strip the ends of the wire appr oximately 5/8" (15 mm).
5 . Insert the hex tool into the locking access, and slightly loosen the hex cap screw . Adjust the speaker to the desired angle (see figure 13), and tor que the hex cap screw down clockwise until snug, about 6 to 8 turns. The speaker remains secur ely in the desired position.
10 SI 3 Speakers • T roubleshooting Tips T r oubleshooting Tips T o refit the grill : 1 . Carefully pr ess the grill back into place. 2 . Insert and tighten down the screws.
Observed Problem Possible Cause(s) Remedial Action 1 Speaker easily lifted from mount assembly Locking hex cap screw not tightened enough Following the steps on page 9, tighten the hex cap screw until it is not possible to remove the speaker . 2 No sound heard from speakers Speaker cables not connected or damaged Output device (e.
12 SI 3 Speakers • Specifications Audio/acoustic and electrical Speaker type ................................... Indoor/outdoor surface mount speaker Frequency range ............................ 75 Hz to 18 kHz, -10 dB, half space Power capacity ..
Extron’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of five years from the date of pur chase.
© 2007 Extron Electronics. All rights reserved. Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.
An important point after buying a device Extron electronic SI 3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic SI 3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic SI 3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic SI 3 you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic SI 3 will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic SI 3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic SI 3.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic SI 3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic SI 3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
