Instruction/ maintenance manual of the product DXP HDMI Extron electronic
Go to page of 48
Setup Guide 68-1370-50 Rev. C 03 12 DVI and HDMI Matrix Switchers DXP DVI Pro DXP HDMI Setup Guide Matrix Switchers.
Safety Pr ecautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压，有触电危险。 .
Conventions Used in this Guide In this user guide, the following are used: CAUTION: A caution indicates a potential hazard to equipment or data. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier .
DXP DVI Pro and DXP HDMI Series • Contents v Contents Introduction .......................................1 About this Guide ................................ 1 About the DXP DVI Pro and DXP HDMI Series Matrix Switchers .......... 1 Application Diagram Examples .
DXP DVI Pro and DXP HDMI Series • Contents vi.
DXP DVI Pro and DXP HDMI Series • Intr oduction 1 Intr oduction This section gives an overview of the Extron DXP 44/48/84/88 DVI Pro and DXP 44/48/84/88 HDMI Series Digital Matrix Switchers and provides application examples.
2 DXP DVI Pro and DXP HDMI Series • Intr oduction The DXP DVI Pro and DXP HDMI series all provide easy integration in applications that require reliable DVI or HDMI signal routing. (A "DVI Pro" signal is HDCP-compliant; a standard DVI signal is not.
3 DXP DVI Pro and DXP HDMI Series • Intr oduction Figure 2. T ypical DXP HDMI Application POWER 12 V 0.4A MAX HDMI 201 Rx 12 HDMI OUTPU T RS-232 PA SS TH RU TxRx POWER 12 V 0.
4 DXP DVI Pro and DXP HDMI Series • Intr oduction.
DXP DVI Pro and DXP HDMI Series • Setup 5 Setup This section describes the rear panels of the DXP switchers and provides instructions for cabling. It covers the following topics: • Setup Procedur e • Rear Panels and Connections • Front Panel Config Port Setup Procedur e Follow these steps to set up and start operating the DXP switcher .
6 DXP DVI Pro and DXP HDMI Series • Setup Rear Panels and Connections Most of the connectors are on the rear panels of the DXP switchers. The following figures show the rear panels of the four DVI models and the four HDMI models. NOTE: The illustrations below show DXP 88 DVI Pro and DXP 88 HDMI models , with 8 input and 8 output connectors.
7 DXP DVI Pro and DXP HDMI Series • Setup b Input connectors — • DVI Pro series: Connect DVI-D source devices to these female 29-pin DVI-I input connectors. Only single-link DVI-D signals are supported. • HDMI series: Connect HDMI source devices to these female 19-pin type A HDMI input connectors.
8 DXP DVI Pro and DXP HDMI Series • Setup c Output connectors — NOTE: The switchers do not alter the video signal in any way . The signal that is output by the switcher is in the same format as the input signal. • DVI Pro series: Connect DVI output devices to these female 29-pin DVI-I output connectors.
9 DXP DVI Pro and DXP HDMI Series • Setup The cable you use depends on your network speed. The switcher supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps (100Base-T — Fast Ethernet), half-duplex and full-duplex, Ethernet connections. • 10Base-T Ethernet requires CA T 3 or higher UTP or STP cable.
10 DXP DVI Pro and DXP HDMI Series • Setup g Remote RS232/RS422 connector — Connect an RS-232 capable host device such as a computer or a touch panel control to the switcher via this 9-pin D connector for serial RS-232 or RS-422 control.
11 DXP DVI Pro and DXP HDMI Series • Setup An optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part number 70-335-01 , is available to connect to this port. (The port does not support RS-422.) The figure below shows the pin assignments for this cable.
12 DXP DVI Pro and DXP HDMI Series • Intr oduction.
DXP DVI Pro and DXP HDMI Series • Operation 13 Operation This section describes the DXP front panel controls and the procedures to configure and begin to operate the DXP switchers.
14 DXP DVI Pro and DXP HDMI Series • Operation c Config port — This RS-232 port is an alternative to the rear panel Remote RS232/RS422 connector . It supports RS-232 only . For more information about the Config port, see " Front Panel Config Port " in the "Setup" section.
15 DXP DVI Pro and DXP HDMI Series • Operation Operations Creating a Tie T o tie an input to an output: 1. Press and release the Esc button to clear any input button, output button, or control button indicators that may be lit. 2. Press and release the Video and Audio I/O buttons to select or deselect video and audio as desired.
16 DXP DVI Pro and DXP HDMI Series • Operation Saving or Recalling a Preset 1. Save a preset — Press and hold the Preset button until it flashes. Recall a preset — Press and release the Preset button. PRESET PRESET PRESET PRESET Preset button b links.
17 DXP DVI Pro and DXP HDMI Series • Operation • Advanced features consist of: • Setting video and audio output mutes • Creating I/O groups • Setting the RS-232/RS-422 port protocol and baud rate NOTE: The switcher is shipped from the factory in lock mode 2.
18 DXP DVI Pro and DXP HDMI Series • Operation T oggle the lock on and off by pressing and holding the V ideo and Audio buttons until the following buttons blink twice (approximately 2 seconds). • The Esc, Video, and Audio buttons blink if the DXP is now in lock mode 2 .
19 DXP DVI Pro and DXP HDMI Series • Operation Selecting the RS-232/RS-422 Port Protocol and Baud Rate (Rear Panel) NOTE: The serial port settings are protected when front panel lock mode 2 is selected. Y ou can view the settings in lock mode 2 but you cannot change them from the front panel.
20 DXP DVI Pro and DXP HDMI Series • Operation 3. T o change a value , press and release the button that relates to the desired value: C O N T R O L I / O Press and release the buttons to configure .
DXP DVI Pro and DXP HDMI Series • Remote Contr ol 21 Remote Contr ol This section describes selected SIS commands that pertain to system setup. It also contains instructions for obtaining, installing, and starting the Matrix Switchers Control Program and for accessing the DXP HTML pages.
22 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Connection Timeouts The Ethernet link times out and disconnects after a designated period of no communications.
23 DXP DVI Pro and DXP HDMI Series • Remote Contr ol EDID (Extended Display Identification Data) EDID is a communications protocol or instruction set for the identification of display devices to computers using the DDC (Display Data Channel) transmission standard.
24 DXP DVI Pro and DXP HDMI Series • Remote Contr ol EDID T able — DDC Source Selection SIS V alue X1( Resolution Refresh (Hz) SIS V alue X1( Resolution Refresh (Hz) 1 Output 1 21 1280x1024 60 2 O.
25 DXP DVI Pro and DXP HDMI Series • Remote Contr ol NOTE: X@ = Input number 0 – maximum number of inputs for your model ( 0 = untied) X# = Output number 1 – maximum number of outputs for your model Command and Response T able for SIS Commands NOTE: The following table is a partial list of SIS commands.
26 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description Quick Multiple Tie T ie multiple inputs to multiple outputs, audio and video E +Q X@ * X# % ...
27 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description Video and Audio Mute Video mute X# *1B Vmt X# *1 ] Mute output X# (video off). Video unmute X# *0B Vmt X# *0 ] Unmute output X# (video on).
28 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description Save and Recall Presets NOTE: If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11 .
29 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description EDID (Extended Display Identification Data).
30 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description Information Requests (Continued) Query controller firmware version Q X2!] Example: Q 1.23 ] The factory-installed controller firmware version is 1.
31 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description IP Setup (Continued) Set gateway IP address .
32 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Command Function ASCII Command (Host to Switcher) Response (Switcher to Host) Additional Description Reset System reset to factory defaults E ZXXX } Zpx ] Clear all ties and presets and reset unit to factory default settings.
33 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Installing and Starting the Matrix Switchers Control Program Another way to operate the switcher is via the Matrix Switchers Control Program. This program is contained on the Extron Software Products DVD (included with the switcher).
34 DXP DVI Pro and DXP HDMI Series • Remote Contr ol 3. Scroll to the Matrix Switchers Control Program and click Install . Figure 21. Matrix Switchers Control Pr ogram Install Link 4.
35 DXP DVI Pro and DXP HDMI Series • Remote Contr ol 4. Click OK . • If you selected a serial port in step 2 , the Matrix Switchers Control Program is ready for operation. • If you selected IP [LAN] in step 2 , the IP Connection window appears. Figure 23.
36 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Accessing the HTML Pages Another way to operate the switcher is via its factory-installed HTML pages, which are always available and cannot be erased or overwritten.
37 DXP DVI Pro and DXP HDMI Series • Remote Contr ol 5. Enter the appropriate administrator or user password in the Password field and click OK . Figure 25. Password Pr ompt for Web Pages 6. If you want your password to be filled in every time you open the browser , select the Remember my password check box.
38 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Using the Web Pages to Configur e the DXP In addition to the System Status page, the DXP has three other pages: Configuration, File Management, and Control. These pages are accessed by clicking the tabs at the top of the screen.
39 DXP DVI Pro and DXP HDMI Series • Remote Contr ol Control page This page lets you control ties and presets on the DXP . Figure 28. Control W eb Page Select the following sub-pages from the left sidebar menu.
40 DXP DVI Pro and DXP HDMI Series • Remote Contr ol.
USA, Canada, South America, and Central America: Extron USA 1001 East Ball Road Anaheim, CA 92805 U.S.A. Europe, Africa, and the Middle East: Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands Asia: Extron Asia 135 Joo Seng Road #04-01 PM Industrial Bldg.
Extron USA Headquarters +800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron U SA - East +1.714.491.1500 +1.919.863.1794 +1.714.491.1517 FAX +1.919.863.1797 FAX Extron Europe +800.3987.6673 (Inside E urope On ly) +31.33.453.4040 +31.33.453.
An important point after buying a device Extron electronic DXP HDMI (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic DXP HDMI yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic DXP HDMI - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic DXP HDMI you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic DXP HDMI will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic DXP HDMI, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic DXP HDMI.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic DXP HDMI. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic DXP HDMI along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
