Instruction/ maintenance manual of the product APP Extron electronic
Go to page of 17
User ’ s Manual Extron Electronics, USA 1230 South Lewis Street, Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 USA Extron Electronics, Europe Beeldschermweg 6C, 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands Extron Electronics, Asia 135 Joo Seng Rd.
Pr ecautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.
P/2 DA2 WM/EC Table of Contents Chapter 1 • Introduction ......................................................... 1-1 About the P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP ............................................................. 1-2 Features .........
P/2 DA2 WM/EC Table of Contents P/2 DA2 WM/EC Table of Contents 1 Chapter One Intr oduction About the P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP Features P/2 DA2 WM/EC.
P/2 DA2 WM/EC Introduction P/2 DA2 WM/EC Introduction 2 Chapter T wo Contr ols and Installation Front and Rear Panels Installing the P/2 DA2 WM/EC P/2 DA2 WM/EC Intr oduction About the P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP The P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP are a one input, two output, high resolution VGA/XGA distribution amplifier with audio.
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation Unity – output signal level is same as that of input with no added peaking 50% – inc reases the output signal level .
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation “Eur o Channel installation” section. 6 Power up all of the input and output devices. 7 The image should now display on scr een. If it does not, double check steps 3 thr ough 6 and make adjustments as needed.
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-7 Connecting audio output Befor e connecting audio output, determine whether your audio system is unbalanced or balanced. Then, follow the instructions below to connect unbalanced audio, or the instructions for “Balanced audio” to connect balanced audio.
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-9 3 . Slide the audio cable connector into the audio output connector on the interface. Installing Architectural Adapter Plates The P/2 DA2 WM AAP may have up to 4 optional adapter plates and the P/2 DA2 EC AAP can have up to 3 adapter plates.
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-10 2-11 P/2 DA2 EC Eur o Channel installation Once the input and output cables have been connected and tested on the P/2 DA2 EC, the distribution amplifier can be easily installed in the Eur o Channel.
P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Operation A Appendix Specifications Faceplate Dimensions Cables Architectural Adapter Plates Mounting Templates P/2 DA2 WM/EC Controls and Installation, cont’d 2-12 OFF — Set both pins to Off if you are attaching a local monitor to the P/2 DA2 WM/EC.
P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix A-3 Audio input Number/signal type ................... 1 stereo, unbalanced Connectors .................................... 1 3.5 mm female stereo jack, 2 channel; tip (L), ring (R), sleeve (GND) Impedance .
P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix Appendix, cont’d A-4 P/2 DA2 WM Faceplate Dimensions Dimensions of the P/2 DA2 WM and its AAP version are provided here for those who wish to make their own customized faceplate. The following diagrams are not drawn to scale.
P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix A-7 Optional Architectural Adapter Plates A variety of optional adapter plates for pass-through connections may be ordered for the P/2 DA2 WM/EC. See the figure A-3 below. The WM model can accommodate up to 4 adapter plates and the EC model can handle up to 3 adapter plates.
P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix A-9 Appendix, cont’d A-8 s e t a l P r e t p a d A l a r u t c e t i h c r A r o t c e n n o C e p y T e l g n i S n o i t p i r c s e d e t a l p r e t.
P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix P/2 DA2 WM Mounting T emplate Use this template as a guide for cutting the hole in the installation surface (wall or furniture). This diagram is shown at actual size. The light gra y area represents where the P/2 D A2 WM enclosure (2.
A-12 The dashed line indicates the recommended cut-out area (3.875” H x 7.525” W) f or the installation surf ace. The solid, outer line (4.50” H x8.
An important point after buying a device Extron electronic APP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic APP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic APP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic APP you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic APP will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic APP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic APP.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic APP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic APP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
