Instruction/ maintenance manual of the product TT23KAEP Exmark
Go to page of 44
TURF TRACER ® TT23KAEP MODEL ONL Y For Serial Nos. 790,000 & Higher Part No. 4500-382 Rev . A.
W ARNING CALIFORNIA Proposition 65 W ar ning The engine exhaust from this product contains chemicals known to the State of Califor nia to cause cancer , birth defects, or other reproductiv e har m.
Introduction CONGRATULATIONS on the purchase of y our Exmark Mow er . T his product has been carefully designed and manufactured to giv e you a maximum amount of dependability and years of trouble-free operation. This manual contains operating, maintenance, adjustment, and safety instr uctions for your Exmark mow er .
Contents Introduction .. . . .. . . .. . .. . . .. . . .. . . .. . . .. . . .. . .. . . .. . . .. . . .. . . .. . . . .. . . 3 Safety .. . . .. . . .. . . .. . . .. . .. . . .. . . .. . . .. . . .. . . .. . .. . . .. . . .. . . .. . . .. . . .. . .. .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER In certain conditions gasoline is extremely ammable and v apors are explosi ve. A re or explosion from gasoline can bur n y ou, others, and cause proper ty damage. • Fill the fuel tank outdoors in an open area, when the engine is cold.
Safety Operation W ARNING Operating engine par ts, especially the mufer, become extremely hot. Sev ere bur ns can occur on contact and debris, such as leav es, grass, br ush, etc. can catch re. • Allow engine par ts, especially the mufer, to cool before touching .
Safety DANGER Operating on w et grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’ s footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning .
Safety W ARNING Hydraulic uid escaping under pressure can penetrate skin and cause injur y . Fluid accidentally injected into the skin must be surgically remov ed within a few hours by a doctor familiar with this for m of injur y or gangr ene may result.
Safety Safety and Instructional Decals • Keep all safety signs legible . R emov e all grease, dirt and debris from safety signs and instructional labels . • R eplace all w or n, damaged, or missing safety signs . • When replacement components are installed, be sure that cur rent safety signs are afx ed to the replaced components .
Safety 103-2432 103-4935 1 16-0404 1 1.
Specications Specications Model Numbers Serial Nos: 790,000 and Higher TT23KAEP Systems Engine • Engine Specications: See y our Engine Owner’ s Manual • RPM: Full Speed: 3600 (No Load) Fuel System • Capacity: 5.0 gal. (18.9 L) • T ype of Fuel: R egular unleaded gasoline, 87 octane or higher .
Specications Tires & Wheels Driv e Front Caster Pneumatic (Air-Filled) Semi-Pneumatic Quantity 2 2 T read T urf Master Smooth Size 18 x 8.50-8 11 x 4.00-5 Ply Rating 4 Pressure 14 psi (96 kP a) Cutting Deck • Model Numbers: – FMD524 – FMD604 • Cutting Width: – 52 inch (132.
Product Overview T orque Requirements Bolt Location T orque Cutter Housing Spindle Nut 140–145 ft-lb (190–197 N-m) Blade Mounting Bolt (lubricate with anti-seize) 55-60 ft-lb (75-81 N-m) Engine De.
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Controls Operator Presence Control (OPC) Levers Located on the upper handle assembly directly abo ve the handle grips. When these lev ers are depressed, the OPC system senses that the operator is in the nor mal operator’ s position.
Operation The brak e lever engag es the park brake on the dri ve wheels . Pull the lev er up and rearward to engag e the brak e. Push the lev er forw ard and down to disengag e the brake . When parking on a steep slope , the wheels m ust be choc ked or block ed in addition to the brak e being engag ed.
Operation Operating Instructions Open the Fuel Shut-Off V alve R otate the v alve 1/4 turn countercloc kwise to turn fuel on. Starting the Engine 1. On a cold engine , place the throttle midway between the “Slo w” and “F ast” positions and place the c hoke in the “On” position.
Operation Driving the Machine Driv e Lev er/Neutral Lock Latch Operation T o loc k the driv e lev ers in “neutral loc k”, squeeze the dri ve levers to the “neutral” position (Do Not squeeze the driv e levers all the w ay back as this will cause the driv e wheels to go into full reverse direction).
Operation A. The front and rear hairpins are in the same holes with the proper spacers under the hair pins . See Figure 5. Figure 5 1. Deck support pin 2. Cutting Height B . The tire pressures are set as directed in Check Tire Pressures in the Maintenance section.
Operation Figure 7 For cutting heights above 3.5 inches (38 mm) use the bottom hole. The rollers will still be effective against scalping. 1. Anti-scalp roller mounting bracket 2. Cutting height 7. F our types of anti-scalp roller assemblies are av ailable.
Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Maintenance Ser vice Inter v al Maintenance Procedure Monthly • Check the battery c harge. Y early • Grease the front caster wheel hubs . • Grease front caster piv ots . • Grease the idler pi vots (Mow er Deck). • Grease the idler pi vot (Pump Driv e).
Maintenance Check Mower Blades Service Interval: Before each use or daily 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brak e. 2. Lift dec k and secure in raised position as stated in the Clean Grass Build-Up Under Deck procedure.
Maintenance Note: If mac hine does not pass any of these tests , do not operate. Contact your authorized EXMARK SER VICE DEALER. Important: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing .
Maintenance If the oil is at room temperature (about 75°F (24°C)), ll only to the “COLD” lev el. Check Tire Pressures Service Interval: Every 40 hours 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brak e.
Maintenance Lubricate Caster Wheel Hubs Service Interval: Y early 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brak e. Figure 1 1 1. Seal guard 2. Spacer nut with wrench ats 2. Remo ve caster wheel from caster forks .
Maintenance Replacement Filters K a wasaki K a wasaki P/N 49019–7001 Change Hydraulic System Filter Service Interval: After the rst 250 hours Every 500 hours/Y early (whichever comes rst) thereafter (Every 250 hours/Y early if using Mobil 1 15W50) Note: Use only Exmark P art No .
Maintenance Figure 12 1. Charge pump cap 2. Loosen 1 1/2 turns only 1. Stop engine and w ait for all moving parts to stop . Raise the rear of the machine up onto jac k stands high enough to raise the dri ve wheels off the g round. 2. Check oil lev el as stated in Check Engine Oil Level section.
Maintenance • Shoulder bolts in ends of speed control crank. • OPC lev er setscrews . • Electric clutc h retaining bolt. • Pump dri ve idler piv ot bolt. • Thumb latc h screw threads on handles . • Caster wheel spacer n uts . • Fuel tank bulkhead tting n uts .
Maintenance control linkage until tabs are positioned correctly . See Figure 13. 3. Pull speed control lev er back to neutral. Check that the neutral safety switc h actuating tab has depressed the plunger of the switch so that there is about 5/16 inc h (7.
Maintenance 2. Loosen the front n ut on left h ydro control link as shown in Figure 15. T ur n the rear control linkage adjusting nut countercloc kwise until wheel rotates forw ard.
Maintenance Hydro Pump Spring T ension Setting 1. F or medium or heavy duty dri ve conditions such as operation with a sulky on steep slopes , a higher spring force may be required on the h ydro pump control ar ms to prev ent the driv e system from stalling .
Maintenance Battery Disposal DANGER Batter y electrolyte contains sulfuric acid, which is poisonous and can cause severe bur ns. Sw allowing electrolyte can be fatal or if it touches skin can cause sev ere bur ns. • W ear safety glasses to shield ey es, and r ub ber glo ves to protect skin and clothing when handling electrolyte.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , do not ov erlook the simple causes . F or example: starting problems could be caused by an empty fuel tank.
T roubleshooting Problem Possible Cause Cor recti ve Action 1. T rac king needs adjustment. 1. Adjust the tracking b y turning knob on the right h ydro control linkage in the direction that the mow er needs to be adjusted to . T urn the knob in 1/4 turn increments until the mow er tracks correctly .
Schematics Schematics Electrical Diagram G006174 3. ST ART POSITION 1 . OFF 2. R UN B + L + S CIRCUIT "MAKE" B + L G + M IGNITION SWITCH TERMINAL CONNECTIONS TERMINAL L PTO , HOUR METER, ENG.
Schematics Hydraulic Diagram 37.
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
Notes: 39.
Notes: 40.
Service Record Date: Description of Work Done: Service Done By: 41.
42.
43.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
An important point after buying a device Exmark TT23KAEP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exmark TT23KAEP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exmark TT23KAEP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exmark TT23KAEP you will learn all the available features of the product, as well as information on its operation. The information that you get Exmark TT23KAEP will certainly help you make a decision on the purchase.
If you already are a holder of Exmark TT23KAEP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exmark TT23KAEP.
However, one of the most important roles played by the user manual is to help in solving problems with Exmark TT23KAEP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exmark TT23KAEP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
