Instruction/ maintenance manual of the product Quest Bagger Exmark
Go to page of 20
® MFG. CO . INC. TM on the purchase of your new Exmark equipment . This product has been carefu lly des igned and manufactured to give y ou a maximum amount of d ependability and y ears of trou ble-free operation .
2 Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Exmark directly at www.
3 Specifications Model Number: 109-5200 Dimensions Overall W idth with Bagger: 48” Deck: 58.0” (147 cm) 52” Deck: 62.0” (157 cm) Overall Length with Bagger: 48” & 52”Deck: 95” (241 cm) Overall Height with Bagger: 48” & 52” Deck: 42.
4 Safety Please carefully read all of the safety instructions and decals in the sa fety section. Knowing this inform ation could help you, your family, pets or bystanders avoid injury. Traini ng • Regard the Exmark Bagger as a piece of power equipment and teach this regard to all who operate this unit.
5 Slopes • Use EXTREME caution when mowing and/or turning on slopes as loss o f traction and/ or tip-over could occur. The operator is r esponsible for safe operation on slopes. Mowing on w et grass or steep slopes can cause sliding and loss of contro l.
6 Slope Chart.
7 Safety and Instr uctional Decals Safety dec als and ins tructions are e asily vi sible to the operator and are l ocated n ear any area of p otential danger.
8 Setup Installing the Weight Parts needed fo r this step: Descr ipti on Qty. Nut, Ny loc 3/8 -16 Flg ........................... 2 Weight ................................................. 1 Screw, Button Head 3/8-16 x 1 . ... . ... . ... . 2 Asm, Weight Support .
9 2. Install the two 3/8-16 x 5 carriage bolts (item 1) through the holes on the frame as shown in Figure 5. Place tw o stiffeners (item 2) on the top and b ottom of the bagger tube (item 4) and install on carriage bolts. Fasten with tw o nyloc nuts (item 3); leave loose to aid installation.
10 If you remov e the spring-loaded hood when it is closed (in the do wn position), the hood may suddenly fly open and you or some one else may be bruised, pinched, or injured in another way . A lw ays open (raise) the hood before you remove or ins tall it on the quick- attach bracket.
11 + Installing the Disc harge Baffle – 52” Deck On ly Parts needed fo r this step: Descr ipti on Qty. Baffle , Disch arge 52”......................... 1 Bolt, Carriage 5/ 16-18 x 3/4... . ... . ... . ... 2 Nut, Ny loc 5/1 6-18 Flg..............
12 Operation Note: The left and right sides of the machine are determined while sitting in the seat in the normal operating position. Emptying th e Grass Bags Be careful when lifting or handling a grass bag that is full.
13 Removing th e Bagger A n unco vered discharge opening will allo w objec ts to be th ro wn in operator’s or by stander’s direction. A l so, contact with blade could occur . Thro w n objects or blade contact can cause serious injury or kill y ou or bystanders.
14 Replacing the D ischarge Deflector A n unco vered discharge opening will allo w objec ts to be th ro wn in operator’s or by stander’s direction. A l so, contact with blade could occur . Thro w n objects or blade contact can cause serious injury or kill y ou or bystanders.
15 holding the handle on the bottom of the grass bag, allowing the liner to slide out. Figure 15 1. Cloth grass bag 2. Bag (liner) Bagging Speed Most often you will bag with the mower throttle in the Fast position and drive at a normal ground speed.
16 Maintenance Note: The left and right sides of the machine are determined while sitting in the seat in the normal operating position. Recommended M a intenance Schedul e(s ) If you leave the key in the ignition switch, someone coul d accidentally start the engine and seriously injure y ou or other bystanders.
17 Inspecting t he Bagger A ttachme nt Inspect the bagger attachment afte r th e first 10 hours of operation, and monthly thereafter. 1. Check the chute, discharge tube, and the bagger top. Replace these parts if they are cracked or broken. 2. Tighten all nuts, bolts, and screws.
18 Tips and Troubleshooting 1. W hen the bags get full, there will be slight blowout from the f ront rig ht corner of the deck. Emptying the ba gs at this point will minimize the potential for the tube to plug. 2. If there is excessive blowout from the deck, check to mak e sure that the rear screen in the hood is clear of grass build up.
19 3-Year Limited Consumer Warranty (30-Day Limited Comme rcial Warran ty) Exmark Quest Riding Mo wers (For units purc hased on or af ter Januar y 1, 2007) Consumer War ranty Condi t ions and Prod ucts Cov er ed Exmark Mf g.
SEE EXMARK’S COMPLETE LINE OF ACCESSORIES RIDING A C CESSORIES CUSTOM RIDE SEA T SUSPENSIO N SYST EM DECK LIFT ASSIST KIT HITCH KIT LI GHT K IT MICRO-MULCH SYSTEM ROLL OVER PROT ECTION S YSTEM (ROPS.
An important point after buying a device Exmark Quest Bagger (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exmark Quest Bagger yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exmark Quest Bagger - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exmark Quest Bagger you will learn all the available features of the product, as well as information on its operation. The information that you get Exmark Quest Bagger will certainly help you make a decision on the purchase.
If you already are a holder of Exmark Quest Bagger, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exmark Quest Bagger.
However, one of the most important roles played by the user manual is to help in solving problems with Exmark Quest Bagger. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exmark Quest Bagger along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
