Instruction/ maintenance manual of the product 4500-435 Exmark
Go to page of 20
ST ANDON For Serial Nos. 790,000 & Higher Part No. 4500-435 Rev . A.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark StandOn. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This manual contains assembly , operating, maintenance, adjustment, and safety instr uctions for your StandOn.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’s footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning .
Safety Safety and Instructional Decals • Keep all safety signs legible . Remo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Specications Specications Model Numbers Serial Nos: 790,000 and Higher ST ANDON Dimensions Length Width Height W eight 35.4 inches (89.9 cm) 18.5 inches (47.0 cm) 14.9 inches (37.9 cm) 50 lb (23kg) T ire T read Size Semi-Pneumatic Tire Smooth 11 x 4.
Setup Setup Assembly Diagram Item Quantity Description 1 8 Nut, Nyloc 3/8-16 Flg 2 2 Plate, Back-Up 3 2 Plate, Adapter 4 8 Screw , HH 3/8-16 x 1 1/4 5 1 Asm, F rame Pull W/Decals 6 1 Asm, Pull Arm W/B.
Setup Installing the StandOn Rider to Mower Mounting the Pull Frame 1. Locate the pull frame and tw o adapter plates . Install the pull frame to the adapter plates using four 3/8-16 x 1 1/4 inc h hex capscrews and four 3/8-16 inch nyloc nuts as shown in Figure 4.
Setup Figure 7 1. Replacement decals e. Align the pull frame and adapter plate assembly to the rear surface of the engine deck. Measure the distance from the bottom of the pull frame to the g round. Choose the mount holes that will attain a distance appro ximately 8 inc hes (20 cm).
Setup Figure 10 1. Pull arm assembly 3. Pull frame 2. Quick connect pins 2. R emov e the 3/8-16 x 4 3/4 inc h hex capscrew . spring disc w asher , and 3/8-16 inc h hex ange side loc k n ut from the piv ot hub . 3. Locate the sulky frame assembly and align with the pull ar m assembly .
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start 1. Make sure y ou understand the controls , their locations , their functions , and their safety requirements . 2. Practice operating the machine without the StandOn until familiar with the controls .
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Lubricate Caster Wheel Hubs Service Interval: Y early 1. Stop engine , w ait for all mo ving parts to stop , and remov e key . Engag e parking brake . Figure 13 1. Seal guard 2. Spacer nut with wrench ats 2. R emov e the caster wheel from the sulky frame .
Maintenance Adjustments Adapter Plate and T ire Adjustment Important: F or optimal perfor mance, the StandOn pull ar m top surface should be horizontal to the ground surface. T o obtain a horizontal pull ar m, the adapter plates and the platfor m wheel can be repositioned (see Figure 14).
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Ex mark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we.
Service Record Date: Description of Work Done: Service Done By: 18.
19.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
An important point after buying a device Exmark 4500-435 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exmark 4500-435 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exmark 4500-435 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exmark 4500-435 you will learn all the available features of the product, as well as information on its operation. The information that you get Exmark 4500-435 will certainly help you make a decision on the purchase.
If you already are a holder of Exmark 4500-435, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exmark 4500-435.
However, one of the most important roles played by the user manual is to help in solving problems with Exmark 4500-435. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exmark 4500-435 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
