Instruction/ maintenance manual of the product EDSR-400 EverFocus
Go to page of 57
INSTRUCTION MANUAL V1.05 2004/3/25 EDSR - 400 4 Channel Duplex Digital Video Recorder EDSR - 600 6 Channel Duplex Digital Video Recorder.
? Refer all work related to the installation of this product to qu alified service personnel or system installers. ? Do not block the ventilation opening or slots on the cover. ? Do not drop metallic parts through slots.This could permanently damage the appliance.
The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance(servicing)instructions in the literature accompanying the appliance. Safety Precautions Warning : To prevent fire or shock hazard, do not expose units not specifically designed for outdoor use to rain or moisture.
Important Safeguards Read Instruction --- All the safety and operating instructions should be read before the init is operated Retain Instructions --- The safety and operating instructions should be retained for fut ure reference. Heed Warnings — All warnings on the unit and in the operating instructions shoul d be adhered to.
Table of Contents 1. Product Overview …………………………………… . ……………… .. … .. … ..Page 1 1.1 Main features ………………………………………………………………… ..... … .. … .1 1.2 Specifications ……………………………………………………………… .
1. Product Overview The EDSR400/EDSR600 Duplex Digital Video Recorder (DVR) a full - featured DVR designed specifically for use in security industry. The DVR incorporates all the benefits of digital video recording , is simple to install, and operates just like a VCR.
Specifications 2 1.2 Specifications 4 ( EDSR400) / 6 (EDSR600) camera inputs (BNC),1Vp - p/75ohm 430 mm (W) x 88mm (H) x 300 (D) Dimension AC100~240V Power Source 100 W max.
Back Panel Connections 2. Back Panel Connections 1 ON/OFF: Main on/off switch. 2 AC100~240V power socket . 3 VIDEO IN: BNC - sockets for composite signal video inputs, automatic 75 Ohm termination. (EDSR400:1~4, EDSR600: 1~6) 4 VIDEO OUT: Loop through video outputs for each input channel.
4 10 ALM - OUTPUT : Two - way contact relay alarm output. In normal condition, this N.C. c ontact shorted to ALM - COM. In alarm status, it is open between ALM - NC and ALM - COM, N.O. is shorted to ALM - COM. ALM - INPUT : Normally Open (N.O) or Normally Close (N.
System Connection 5 3. System Connection The installations described below should be made by qualified se rvice personnel or system installers. Before Installation Please refer to the following diagram for the system connections .
Front Panel Keypads 4. Front Panel Keypads SHUTTLE : In Playback mode, turn the shuttle ring to fast forward/rewind the picture (600X maximum). In Pause mode, turn the shuttle dial to slo w forward/rewind the picture (1/32 maximum). JOG : In Pause mode, turn the jog dial to step forward/rewind the Pict ure.
LEDs: LEDs for HDD1, HDD2 , ALARM and LAN access (from left to right) . IR Remote Controller receiver 7 Display: Press this key to switch ON/OFF for camera title, date/time and HDD status. Hold this key longer than 2 seconds for displaying the event log list.
Operation 8 (1) Insert a HDD (IDE) for Video Storage (2) Connect cable for video/audio input and video/audio out, The detail connection is described in SYSTEM CONNECTION .
MENU flow 6. MENU FLOW CLOCK ( See page 11 ) : 2004/2/27 FRI : 13:01:02 CLOCK SETTING MENU DATE TIME MENU LANGUAGE: ENGLISH VIDEO SYSTEM: NTSC VERSION: 1.
BUZZER ( See page 22 ) BUZZER SETTING MENU BUZZER : ENABLE RECORD - IN : ON ALARM - IN : ON MOTION - IN : ON DISK FULL : ON VIDEO LOSS: ON TIMER : ON ARCHIVE ( See page 23 ) PICTURE SIZE TIME STAMP TI.
MENU 11 In CLOCK/LANGUAGE SETTING MENU , we define: (1) DATE : Current date, format: YYYY/MM/DD Year: 2000 ~ 2099, Month: 01~ 12, Date: 01~31, Week: Sunday~Saturday (2) TIME : Current time, format: HH.
MENU 6 .2 TIMER SETTING MENU 12 Timer records can be defined for 12 individual start and end tim es. (1) WEEK: This select the week day for the timer to record on schedule. DLY means daily record. (2) START: Enter the start time for timer recording. (3) STOP: Enter the end time for timer recording.
MENU (1) CH (Channel): Input channels 1~4 for EDSR400, 1~6 for EDSR600. (2) OP (Operation): ON includes the camera in the sequence, OFF skips the camera in the sequence. (3) DWELL (DWELL TIME) : Dwell Time is individual adjustable for each channel. The dwell ing time for the sequencer can be set between 0 - 99 seconds.
MENU 14 6 .4 TITLE SETTING MENU In TITLE SETTING MENU , we define: The Title Setting Menu allows you to assign a title to each came ra input. Title with up to 12 characters is supported in each channel. The available alphanumeric characters are: 0,1,2,3,4,5,6,7,8,9, A,B,C,D, … X,Y,Z.
6 .5 COVERT SETTING MENU COVERT SETTING MENU CH OP 1 OFF 2 OFF 3 OFF 4 OFF (5 OFF) (6 OFF) In COVERT SETTING MENU , we define: The covert setting menu allows you hide the desired camera on th e display in a blue background. Change setting to ON for covering camera.
In ALARM RECORDING MENU, we define (1) CH (Alarm input) : Select alarm input or RST for alarm reset input. (2) OP (OPERATION) : ON : Records when alarm occurs. OFF : No reaction when alarm occurs. (3) TYPE : Select alarm type: N.C. : Normally Closed with time out function counting from alarm start (set in DURATION) N.
MENU (1 ) CH (Channel) : Video input channel (2) OP (Operation) : Default: OFF ON: The device will respond recording when motion occurs. OFF: The device will not respond recording when motion occurs . (3) SEN (Sensitivity) : HIGH, MIDDLE or LOW adjustable.
MENU ( 5) Press 1 - 4/6 TO MANUAL EDIT: Use the numeric keys (1~4 for EDSR - 400 / 1~6 for EDSR - 600) to select a camera for setting the detection areas. The selected camera appears with a 16 x 12 grid (detection zones ): Follow the Dialog for further operation.
MENU 19 In NORMAL RECORDING MENU, we define (1) NORMAL RECORD: SPEED : To set the normal recording speed. Maximum 60 (NTSC) / 50 (PAL) . QUALITY: Video recording quality setup for setting the quality of the vi deo picture by selecting a compression rate.
6 .9 NETWORK SETTING MENU IP ADDRESS NET MASK ADDRESS GATEWAY ADDRESS MAC ADDRESS USER - NAME PASSWORD LEVEL NETWORK SETTING MENU : 192 .168.010.005 : 255 .
MENU (1) RS232 BAUD RATE: There are 6 different speeds that can be used to transmit inst ruction or information through the RS232 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud, 19200 baud,and 3840 baud. The default setting from the factory i s 9600 baud.
In BUZZER SETTING MENU, we define the buzzer ON/OFF for following event: RECORD - IN, ALARM - IN, MOTION - IN, DISK FULL, VIDEO LOSS AND TIMER MENU 22 6 .
MENU 6 .12 ARCHIVE SETTING MENU (1) PICTURE SIZE : Selects picture size for copying image to CF card: Big size:720x480 / 720x576 for NTSC / PAL. Small size:352x240 / 352x288 for NTSC / PAL. (2) TIME STAMP : ON : Shows the time stamp on the picture when copying image to CF c ard.
6 .13 CALL MONITOR SETTING MENU 24 CH DWELL EVENT 00 07 SECS NONE 00 07 SECS NONE 00 07 SECS NONE 00 07 SECS NONE (00 07 SECS NONE) (00 07 SECS NONE) CALL MONITOR SETTING MENU In the CALL MONITOR SETTING MENU, we define the sequences of each CH for call monitor .
MENU 25 6 .14 DISK SETTING MENU (1) DISK USAGE: HDD - 1, HDD - 2 (2) SIZE: Applied HDD size. (3) RECORD POS: HDD usage rate, record position, “ * ” shows the active HDD (4) PLAY POS: current playb.
MENU 26 6 .15 SYSTEM SETTING MENU (1 ) PLAY WITH AUDIO: AUDIO - 1, AUDIO - 2 ON/OFF: Play back with or without audio. (2) PLAY SPEED: Set the playback speed.
7 .1 INSTANT RECORDING Press REC key to start continuous recording with setting of “ NORMAL RECORD ” . The recording rate and recording quality are set in the RECORD S ETTING MENU. The LCD screen on the front panel of DVR will display as follows : Recording REC Press STOP key to stop recording.
8 .1 NORMAL PLAYBACK Press the PLAY key to start playing back the stored image/audio from the last SEGMENT. (1) Playback (2) Fast Forward/Reverse Playback During playing back, turn the SHUTTLE ring clockwise to start fast forward playing back. The speed will be shown on the screen at the bottom of the scree n.
8 .2 SEARCH PLAYBACK Press SEARCH key to enter the SEARCH MENU dialog. Search Playback SEARCH 29 SEGMENT SEARCH 0001 0002 0003 2003/04 /24 19/03 /29 HDD1 2003/04/25 12/30/30 HDD1 2003/05/20 12/00/00 HDD2 SEARCH MENU BY SEGMENT LIST BY ALARM LIST BY DATA TIME Turn the JOG dial to select BY SEGMENT LIST and press ENTER key.
(2) Alarm List search playback 30 A01 : Alarm recording by Alarm - in 1. M03: Motion recording by camera 3. T : Timer recording. PL: automatic record restart after end of power loss : The icon means there is more than one page list. Use “ SHTTLE ” to change between pages or use “ JOG ” to select one list.
(3) Date/Time Search Playback DATE/TIME SEARCH YEAR/MM/DD HH:MM:SS HDD 2003 /01 /01 21: 33: 26 1 PRESS SEARCH TO START SEARCH PRESS MENU TO EXIT 31 Notice: If there is no image stored in the date/time specified then the machine will start playing back from the nearest set time automatically.
DATA EXPORT Insert a Compact Flash card into the Compact Flash slot on the f ront panel of DVR. When inserting the Compact Flash card, make sure that insert dir ection is correct. NOTE: COPY function is not possible during RECORD. Stop recording to enable COPY function! Turn the JOG Dial clockwise to choose your desired image.
COPY Press COPY key and then the copy menu and instruction appears. The main monitor switches to full screen display with following OSD: 33 Press the PLAY key to start playing back.
9 .3 EXPORT EVENT LOG LIST DATA EXPORT This function allows to export the event log list to CompactFlas h – Card. The generated text file is in *.txt format.
MONITOR VIEWS / OPERATION 10. MONITOR VIEWS / OPERATION 10.1. MAIN MONITOR The EDSR400/EDSR600 digital recorders provide 1 main monitor and 1call monitors.
Press CALL to change settings for CALL monitor. The Main monitor shows following dialogue: MONITOR VIEWS / OPERATION 10.2. CALL MONITORS 36 CALL SETTING CALL MONITOR.
RJ45 (RS485) pin assignment 11. REMOTE CONTROL 11.1 RS - 485 REMOTE CONTROL The new standard EverFocus EDSR remote protocol allows challengi ng installations with DVR remote control at different installation sites.
IR Remote Controller The remote controller (RC - 200, Figure 1) is an accessory to enhance the handy operations o f the DVR. You can perform all the settings and operations by the rem ote controller. The effective distance is up to 10 meters without any obstacle.
12. View From Internet/Intranet Basic Operations and Login Display: Go to the Internet Explorer, key in the network IP address, for example, http://192.168.10.5 (must be the same IP address as the one assigned to the unit from the Network Setting Menu.
Main Screen Above diagram is the main screen display. The icons on the lower corner of the screen are mainly for contr ol and Configuration, those on the right corner are for status indication. If any icon is grayed, it means that the specific function is no t accessible in the current mode.
10. The system allows up to 3 ways playback video, by SEGMENT, ALARM LIST and DATE TIME . ( Playback by SEGMENT LIST, click Refresh to show list) ( Playback by Date time) 41 ( Playback by ALARM LIST, click Refresh to show list) View From Internet/Intranet Above pictures are sampling from EDSR900 9 CH DVR for reference.
11. All available segments are shown in the list. Click to select an d highlight. 12. Click to playback selected video segment. 13. Press this icon to show the segment or list. 14. Current connection and playback status is shown along with date and time.
Appendix - A LAN Functional Specification Specifications: Network Interface: 10Mbits/s Ethernet (10Base T) LAN controller Chip: RealTek 8019 LAN Connector: RJ - 45 Protocol: HTTP,TCP/IP.
Appendix - B ? When Recording with 160GB HDD 44 Lower Low Basic Standard High Superior : 15 kB : 19 kB : 23 kB : 27 kB : 31 kB : 35 kB ( Estimated with typical image - low noise level) Time Lapse Mode Recording Time Table Reference:24H=1 day.
? When Recording with 320GB HDD Lower Low Basic Standard High Superior : 15 kB : 19 kB : 23 kB : 27 kB : 31 kB : 35 kB Appendix - B 45 ( Estimated with typical image - low noise level) Reference:24H=1 day.
Appendix C: Serial Interface Specifications 2. Transmission setting PIN # NAME PIN # NAME 1 NOT CONNECTED 1 NOT CONNECTED 2 TXD 2 RXD 3 RXD 3 TXD 4 NOT CONNECTED 4 NOT CONNECTED 5 GROUND 5 GROUND 6 NO.
3. Remote Control Protocol A computer or a terminal can be used to control the unit by send ing the packet as following. 47 1 - 1. Sample control code packets Example1 : A packet that send "REC&q.
48 2 - 1. The format of message packet is as follows: Length Byte (Prefix: 0x86, 0x87, or 0 x88 ..... ) Receiver ID high byte Receiver ID low byte Opcode Byte Data Byte1 Data Byte2 Data Byte3 Checksum Byte 2 - 2. Length Byte This Length Byte is also a prefix.
49 2 - 3. Receiver ID 2 - 3. Receiver ID 1). Individual receiver ID Decimal 14bit binary value Hbyte Lbyte Receiver ID (EDSR) 0 0000000 0000000 00 00 ID = 0 1 0000000 0000001 00 01 ID = 1 2 0000000 0000010 00 02 ID = 2 .
50 2 - 4. Opcode Byte & Data bytes 2 - 4 - 1. OPcode OPcode Data1 Function 0x4B Keycode A remote key pressed 0x4D command Matrix command 2 - 4 - 2.
Appendix - D 51 Alarm I/O pin assignment T he alarm connector, Figure 1 , is used to provide one sensor alarm input for each camera inpu t. For easy operation, an alarm extension board, Figure 2 , is provided to connect to the alarm connector.
EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin - Tai Wu Road, Hsi - Chi, Taipei, Taiwan TEL: +886 - 2 - 26982334 FAX: +886 - 2 - 26982380 www.everfocus.com.tw USA Office: 2445 Huntington Drive, San Marino, CA 91108, U.S.A. TEL: +1 - 626 - 844 - 8888 FAX: +1 - 626 - 844 - 8838 www.
An important point after buying a device EverFocus EDSR-400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought EverFocus EDSR-400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data EverFocus EDSR-400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, EverFocus EDSR-400 you will learn all the available features of the product, as well as information on its operation. The information that you get EverFocus EDSR-400 will certainly help you make a decision on the purchase.
If you already are a holder of EverFocus EDSR-400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime EverFocus EDSR-400.
However, one of the most important roles played by the user manual is to help in solving problems with EverFocus EDSR-400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device EverFocus EDSR-400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
