Instruction/ maintenance manual of the product P1225LGRL 527.25155 ESCALADE
Go to page of 16
OWNER'S MANUAL CHAMPION 8 FT. DROP POCKET POOL TABLE MODEL NO. P]225LGRL 527.25155 MODEL NO. P]227LGRLA 527.25165 1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY. Read each step completely before beginning each step. 2. SOME SMALLER PARTSMAY BE SHIPPED INSIDE LARGER PARTS.
CAUTION THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER PRESSURE! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT OF THE REACH OF CHILDREN! DO NOT USE OR STORE NEAR HEAT SOURCE ! FLAMES ! SPARKS OR WHEN SMOKING! WORK AREA MUST BE WELL VENTILATED.
ASSEMBLE TWO LEG PEDESTALS AS FOLLOWS: 1. Begin by opening hardware kits and sod hardware. Remove the mounting plate from one leveler #22 and attach it to bottom of left leg # 19 using two screws #27 and two dowel connectors #26. Cover holes with adhesive hole covers #28.
40 5O 15 WARNING Holes marked by arrows MUST be on the TOP when attached to leg pedestals. 4O 5o 5. Attach beam # 15 by using four bolts #40, eight washers #50, and four tocknuts #49 for each of the leg mounting location. Place one washer between the bolts and beam and one between leg posts and tocknuts.
NOTE: Screwheads should be flush with or below the top of the slats #16 and #17. 15 16 Detail A ,8 H 36 Slot should be straight up and down Hole for dowel connector #36 is closer to the top of beam. 9. Place long slats #16 (50 inches long) and short slats # 17 (36 inches long) across table from beam to beam as shown in figure 6.
LEVELING BASE FRAME 11. Using a carpenter's level, level table as well as possible. It is easier to do it now rather than after the slate is on frame.
¢AUTION: Be sure that the side of the play surface with the _oles faces up. 16 17 DETERMINE THE TOP SIDE OF THE PLAY SURFACE! IMPORTANT: Be sure countersunk holes in all three 17. table top sections #9 and # 10 face up: See Figure 10. NOTE: Slatron tables have "match" Iine markings like those shown above (letters A, B, C).
SHIMMING INSTRUCTIONS General Rules • Accomplish the leveling of slate with as few shims as possible. • Slate is brittle. Do not tap with a hammer or tiqhten screws unreasonable tight. You will not be abqe to compress the slate. You must shim up the slate to level.
WARNING: Applying the cloth First Glue ] Application 22. Make sure slate/slatron is dry and free of dust. NOTE: Before spraying adhesive, cut a podion of the shipping cation to use as a shield to prevent cement overspray. 23. Place cloth over slate/slatron with equal overhang on all sides.
Slate Look along the front edge of the side rails to be sure they align. Side rails must be in a straight line with each other, 4 --_-lb- I This view is shown without side and corner caps installed to help I | identify the rails. Side caps must be installed before the rails are attached I to slate.
38. 39. AlCach end aprons # 12 to recessed area on the underneath side of the end rails (#4). CENTER THE APRONS WITHIN THE LENGTH OF THE RAILS. Hold apron in place and spot the location of the mounting holes on the rails. Punch pilot holes in rail using an awl (or 8d nail) and hammer.
41. Before attaching the drop pockets to the rails you will need to tri m two of them to fit into the side pockets. (See figure 25) Inserhhe corner and side drop pockets (the two that you have trimmed) into the drop pocket openings on the table. THE LIP ON THE POCKETS GO INTO THE RECESSED AREA ALONG THE INSIDE RIM OF THE CORNERAND SIDE CAPS.
ONE YEAR LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADE ® SPORTS Product (hereinafter referred as the "Producf_). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original purchase.
! I_q_ 1 2 3 4 5 6 7 8 9 lO 822-3 2A-4049-57 2A-4050-57 2A-4051-57 5A-6827-00 3M-6522-00 3M-6523-00 3M-6546-00 809-551 2W-6029-00 809-552 2W-6030-00 1 I 2A-6508-07 12 2A-6509-07 13 3A-6007-00 14 Q-600.
18 17. 36 NOTE: Not all parts are shown. Also see page 16. 10 17 3 _9 o ...... 50 50 49.
8_ r_ i C>. oo C_ Q Q 45 NOTE: Not all parts are shown. Also see page 15. 26 21 20 45.
An important point after buying a device ESCALADE P1225LGRL 527.25155 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ESCALADE P1225LGRL 527.25155 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ESCALADE P1225LGRL 527.25155 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ESCALADE P1225LGRL 527.25155 you will learn all the available features of the product, as well as information on its operation. The information that you get ESCALADE P1225LGRL 527.25155 will certainly help you make a decision on the purchase.
If you already are a holder of ESCALADE P1225LGRL 527.25155, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ESCALADE P1225LGRL 527.25155.
However, one of the most important roles played by the user manual is to help in solving problems with ESCALADE P1225LGRL 527.25155. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ESCALADE P1225LGRL 527.25155 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
