Instruction/ maintenance manual of the product RX1290 Ericsson
Go to page of 176
RX1290 Multi-Format Receive r Software Version 3.0.0 (and later) REFERENCE GUIDE EN/LZT 790 0003/2 R1A.
Preliminary Pages ENGLISH (UK) - READ THIS FIR ST! If you do not under stand the co ntents of this man ual. DO NOT OPERATE THIS EQUIPMENT . Also , translation into any EC official language of thi s manual can be made av ailable, at your cost. ITALIANO - LEGGERE QUESTO AVVISO PER PRIMO! Se non si capisce il contenuto del pre sente manuale.
Preliminary Pages EN/LZT 790 0003/2 R1A 2011-0 6-06 iii Contents Chapter 1: Introduction This chapter identifies the equipment versions covered by this Reference Guide; describes the purpose of the equipment in a typical system; provides a summary of its main features; identifies the controls, indicato rs and connectors.
Preliminary Pages Introduction This Reference Guide provides instructions and information for the installation and operation of the RX1290 Multi-Format Receiver. This Reference Guide should be kept in a safe place for reference for t he life of the equipment.
Preliminary Pages Registered Trademarks Ethernet ® Registered trademark of Xerox Corporation. Dolby ® / AC-3 ® Registered trademarks of Dolby Laboratories Licensing Corporation. Trademarks Alteia ™ Trademark of Ericsson AB. Macrovision This product incorporates copyright protection technology that is protect ed by U.
Preliminary Pages Caution! Cautions give information which, if strictly followed, will prevent damage to equipment or other goods. They are highlighted for emphasis, as in this example, and are placed immediately preceding the point at which the reader requires them.
Preliminary Pages Customer Services Europe, Middle East and Africa Tel: +44 (0) 23 8048 445 5 Fax: +44 (0) 23 8048 4467 Email: tvsupportemea@ericsso n.com Americas Tel: +888 671 12 68 Tel: +678 812 62 55 Fax: +678 812 6262 Email: tvsupportam ericas@ericsson.
Preliminary Pages EN/LZT 790 0003/2 R1A 2011-0 6-06 viii Return of Equipment If you need to return equipment for repair please contact your local Ericsson Customer Services Department.
1 Introduction Chapter 1 Contents 1.1 Scope of This Reference Guide ........................................................... 1-3 1.1.1 Who Should Use This Reference Guide ............................................... 1-3 1.1.2 What Equipment is Covered by This Reference Guide .
Introduction EN/LZT 790 0003/2 R1A 1-2 List of Figures Figure 1.1 Front View of a RX1290 Multi-Format Receiver ................................... 1-3 Figure 1.2 Typical Satellite Compression System ................................................. 1-8 Figure 1.
Introduction 1.1 Scope of This Reference Guide 1.1.1 Who Should Use This Reference Guide This Reference Guide is written for operators/users of the RX1290 Multi-Format Receiver. It describes the unit’s functions and op eration. The Reference Guide is written to assist in the installation and day-to-day care and op eration of the unit.
Introduction T able 1.2 Hardware Options Marketing Code Price Object Number Supply Object Number Description RX1290/HWO/DVBS2 FAZ 101 0116/3 ROA 128 3800 DVBS2 I/P SAT DEMOD OPTION RX1290/HWO/DVBS2/IF.
Introduction Marketing Code Price Object Number Supply Object Number Description RX1290/SWO/LDELAY FAZ 101 0116/21 FAT 102 0223 LOW LATENCY DECODE MODE (4:2:0 ONLY) RX1290/SWO/HSETHER FAZ 101 0116/19 .
Introduction - Up to 40 preselected choices can be stored within the unit. • Multiple Inputs (Satellite Receivers): - L-band Satellite Receivers have four inputs. • Video Decoding: - MPEG 4:2:0 mode support. - MPEG 4:2:2 mode support (MPEG-2 Only).
Introduction - Front Panel User Interface. 1.2.2 Inputs 1.2.2.1 1.2.2.2 1.2.2.3 1.2.2.4 1.2.2.5 1.2.2.6 1.2.3.1 1.2.3.2 1.2.3.3 ASI Input (Decoder) One BNC connector sup porting both byte-mode a nd single packet burs t mode. Remote Control An RJ-45 Ethernet connector for connection to a PC or network switch to provide SNMP control.
Introduction • Four BNC connectors providing unbalanced audio output. Data Output 1.2.3.4 1.2.3.5 • RS-232 asynchronous low-speed data output carried on a 9-way, D-type, female connector.
Introduction 1.3.2 Input Connections The Satellite Receiver interfaces directly to Low-Noise Block (LNB) and accepts an intermediate frequency (IF) input in the band 950 - 2150 MHz (L-band) for operation in the specified symbol-rate range (see Annex B, Technical Specification ).
Introduction 1.4 The T elco Receiver/Decoder 1.4.1 Typical Decoder System The Decoder is a component of Ericsson’s range of equipment. It is designed for use by broadcasters and distributors of video and audio Services. It can be used as a Transport Stream monitor or to decode signals received over a telecommunications network.
Introduction Figure 1.5 Role of the Decoder 1.5 Control Modes 1.5.1 Introduction The Multi-Format Receiver is designed for unattended operation. Once set-up, the unit requires no further attention except to ensure the fans are working. There are up to three control modes associated with the Receiver (dependent upon options fitted).
Introduction 1.6 Guided T our 1.6.1 Construction The Multi-Format Receiver is constructed using a screened self-ventilat ed modular system. All operational inputs and outputs are via rear-panel connectors. The unit may be operated freestanding or mounted in a 19-inch rack.
Introduction 1.6.4 Rear Panel Inputs and outputs to the unit are taken via the rear panel. Connector descriptions are given in Chapter 2, Installing the Equipment and Chapter 6, Options.
Introduction EN/LZT 790 0003/2 R1A 1-14 BLANK.
2 Inst alling the Equipment Chapter 2 Contents 2.1 Read This First! .................................................................................... 2-3 2.1.1 Handling ...............................................................................
Installing the Equipment EN/LZT 790 0003/2 R1A 2-2 2.7.9 Alarm Connector and Relay ............................................................... 2-15 2.7.10 RS-232 Low-speed Asynchronous Data Output ................................ 2-15 2.7.11 Serial Remote Control .
Installing the Equipment 2.1 Read This First! 2.1.1 Handling The equipment must be handled and installed carefully and thoughtfully to prevent safety hazards and damage. 2.1.2 Installing the Equipment Ensure the personnel designated to fit the unit have the appropriate skills and knowledge.
Installing the Equipment Where appropriate, ensure this product has an adequate level of lightning protection. Alternatively, during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the supply outlet and disconnect the output equipment.
Installing the Equipment 2.3.2 Ventilation 2.3.3 Openings in the Covers Si de openings in the unit, as well as side-mount ed cooling fans, are pr ovided for ventilation. The y ensure reliable opera tion of the product and protect it fro m overheatin g.
Installing the Equipment 2.3.4 Installing Cables - Safety Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cables at plugs, convenience receptacles, and the point where they exit from the appliance.
Installing the Equipment Warning! The RX1290 should only be operated from the type of power source indicated on the marking label. If you are not sure of the type to your business, consult your appliance dealer or local power company. Do not overload wall outlets and extension cords as this can result in a risk of f ire or electric shock.
Installing the Equipment If the colors do not correspond with the colored markings identifying the terminals in a locally supplied plug, proceed as in Table 2.2 . The inclusio n of Table 2.2 is for reference. Table 2.2 Non Standard Supply Cord Wire Colors Wire Color (UK) Action green-and-yellow .
Installing the Equipment Figure 2.3 Location of the T echnica l Earth 2.7 Signal Connections 2.7.1 General Caution! It is strongly recommended that the terminal marked at the rear panel of the equipment is connected to a site Technical Earth before any external connections are made and the equipment is powered.
Installing the Equipment Power Supply AC Power Supply Option Cards ASI FRAME SYNC REMOTE CONTROL ETHERNET ASI In Frame Synchronization RS232/485 10 /100Base-T G.
Installing the Equipment 2.7.2 ASI/HD-SDI/SD-SDI OUT The unit has three ASI/SMPTE 292M video (HD-SDI)/656 video (SD-SDI) outputs in the standard configuration. The output standard must be selected from the user interface or remote control interface. The ASI/HD-SDI/SD-SDI output is coaxial via BNC connectors.
Installing the Equipment In addition, four unbalanced digital audio outputs are available via separate BNC connectors. Table 2.5 Analogue/Digital Audio Connectors AUD 1 Item Specification Connector ty.
Installing the Equipment Table 2.7 SVGA Connector Item Specification Connector type 15 -w a y D -t yp e Connecto r designation Video O ut Pin-outs 1 Red / Pr 75 Ω , 0,7Vt-t 2 Green / Y 75 Ω , 0,7Vt-t 3 Blue / Pb 75 Ω , 0,7Vt-t 4 NC 5 Video GND 6 Red GND 7 Green GND 8 Blue GND 9 NC 10 Sync GND 11 NC 12 NC 13 H-Sync 14 V-Sync 15 NC 2.
Installing the Equipment Table 2.8 Frame Sync Hi-Z Connector Item Specification Connecto r type BNC 75 Ω socket Connecto r designation FRAME SYNC Pin: Centre Analogue Black a nd Burst Input Shield Ground/Chassis Impedance Last unit must be terminated with 75 Ω 8 1 2.
Installing the Equipment 1 5 6 9 2.7.9 Alarm Connector and Relay The alarm relay connector has a summary relay. The summary relay is activated whenever the unit detects an alarm, or the power is switched off.
Installing the Equipment EN/LZT 790 0003/2 R1A 2-16 Item Specification Pin 5 - Ground (RS-232) Pin 6 - Reserved Pin 7 - No connection Pin 8 - Reserved Pin 9 - Reserved 5 1 6 9 2.
3 Operating the Equipment Locally Chapter 3 Contents 3.1 Powering the Equipment ...................................................................... 3-5 3.1.1 Switching On .............................................................................
Operating the Equipment Locally 3.7.12 Setting Up VITC ................................................................................. 3-19 3.7.13 Setting Up Closed Captions ............................................................... 3-20 3.7.14 Setting Up ITS Insertion .
Table 3.13 Setting Aspect Ratio ........................................................................... 3-16 Table 3.14 Setting Video Delay Mode .................................................................. 3-16 Table 3.15 Setting Video Ddelay Mode .
Operating the Equipment Locally EN/LZT 790 0003/2 R1A 3-4 BLANK.
Operating the Equipment Locally 3.1 Powering the Equipment 3.1.1 Switching On Caution! This equipment should not be operated unless the cooling fa n is working and there is free-air flow around the unit. Connect the signal inputs and AC power supply to the Multi-Format Receiver and power up the unit.
Operating the Equipment Locally 3.2 Front Panel Controls and Pushbuttons Front Panel items are described under Section 1.6, Guided Tour . Figure 3.2 Front Panel Controls and Pushbuttons 3.3 Front Panel Operating Modes 3.3.1 General Operating the Multi-Format Receiver from the Front Panel is via two operating modes: Navigate Mode ( see Section 3.
Operating the Equipment Locally Pushbutton LEDs will be updated to indicate which pushbutton presses are still valid as each navigation pushbutton press event is processed. For example, a lit Up pushbutton LED indicates there are pages above the current one.
Operating the Equipment Locally 3.4.2 Selecting a Menu Option Some items shown in the right display area of the front panel LCD display have a set number of options. An example of this is the VIDEO TEST PATTERN (Menu 3.1.6) which has a number of preset Video Test Patterns associated with it.
Operating the Equipment Locally 3.5 Setting Up Preset Services (Menu 1) 3.5.1 Using Preset Services This group allows up to 40 Services to be stored as presets. Selecting a Service from the preset list in Menu 1 automatically reconfigures the Multi-Format Receiver to receive that Service with its associated parameters set as stored.
Operating the Equipment Locally 3.6 Setting Up the Input (Menu 2) 3.6.1 DVB-S2 Satellite Receiver (TT1290/HWO/DVBS2 and TT1290/HWO/DVBS2/IF/CONST) Table 3.6 Setting Up the DVB-S2 Satellite Receiver Step Action Result 1 Go to Menu 2.3 and select SOURCE 1.
Operating the Equipment Locally 3.6.1.1 DVB-S2 Inp ut Option Card TT1290/HWO/DVBS2/IF/CONST The DVB-S2 demod option TT1290/HWO/DVBS2/IF/CONST offers three L-band inputs plus an IF input. If this input option card is fitted in the receiver then note that Menu 2.
Operating the Equipment Locally 3.6.3 10/100BaseT Input – RX1290/HWO/IP Table 3.8 steps through the set-up procedure of the Telco Receiver using Menu 2 Input, and the IP input. Table 3.8 Setting Up the IP Interface Step Action Result 1 Connect the Ethernet cable to the IP input connector.
Operating the Equipment Locally 3.6.4 100/1000BaseT Dual IP I nput – RX1290/HWO/GIGE Steps through the set-up procedure of the Receiver using Menu 2 Input, and the IP input. Table 3.9 Setting Up the Dual IP Interface Step Action Result 1 Connect the Ethernet cables to the IP input connectors.
Operating the Equipment Locally Step Action Result 12 Return to Input Menu 2, it should display the current status. If status is NOT LOCKED, verify that the cable is properly connected and that all values have been entered correctly. 3.7 Service Configuration (Menu 3) 3.
Operating the Equipment Locally Step Action Result 3 Scroll to Menu 3.1.7 and edit the video test pattern to be displayed. Press Save . Edits the video test pattern to be displayed. 4 Scroll to Menu 3.1.10 and edit the parameter for framesync enable (ENABLED or DISABLED).
Operating the Equipment Locally Table 3.13 Setting Aspect Ratio Step Action Result 1 Scroll to Menu 3.1.9 and edit the parameter for aspect ratio (4:3, or 16:9). Press Save . Edits the parameter for the output SD aspect ratio. 3.7.5 Setting Video Delay This menu allows the user to vary the output presentation delay.
Operating the Equipment Locally Table 3.16 Setting Low delay mode Step Action Result 1 Go to Menu 3.1.15 and edit the option displayed. (LOW DELAY MODE, NORMAL). Press Save Gains access to the low delay option. There is a choice between low d elay and normal mode.
Operating the Equipment Locally Step Action Result 3 Scroll to Menu 3.3.4 and edit the Audio 1 digital output format (AES3 or AC-3) and output routing (STEREO, MIXED TO BOTH, LEFT TO BOTH, or RIGHT TO BOTH). Press Save . Edits the Audio 1 digital output format and output routing.
Operating the Equipment Locally Step Action Result 2 Scroll to Menu 3.8.1 and edit the High speed data output (ENABLED or DISABLED). Press Save . The unit receives and displ ays the correct bit- rate. 3 Scroll to Menu 3.8.3 and edit the Forward to Gateway ON/OFF and the Gateway IP address menu.
Operating the Equipment Locally 3.7.13 Setting Up Closed Captions Table 3.22 Setting Up Closed Captions Step Action Result 1 Scroll to Menu 3.10.3 and edit the parameter for enabling Closed Captions pass-through (ENABLED or DISABLED). Press Save . Edits the parameter for enabling Closed Captions pass-through.
Operating the Equipment Locally 3.7.17 Setting Up Video Index Table 3.26 Setting Up Video Index Step Action Result 1 Scroll down to Menu 3.10.7 and edit the parameter for enabling Video Index insertion (ENABLED or DISABLED). Press Save . Edits the parameter for enabling Video Index pass-through.
Operating the Equipment Locally 3.7.21 Setting Up VANC Dat a Insertion Table 3.30 Setting Up VANC Data Insertion Step Action Result 1 Scroll down to Menu 3.11.1 and edit the parameter for enabling VANC Data insertion (ENABLED or DISABLED). Press Save .
Operating the Equipment Locally 3.7.25 Setting Up DVB Subt itles Table 3.34 Setting Up DVB Subtitles Step Action Result 1 Scroll down to Menu 3.15.1 and edit the parameter for enabling DVB Subtitles (ENABLED or DISABLED). Press Save . Edits the parameter for enabling DVB Subtitles.
Operating the Equipment Locally 3.8.2 Basic Interoperable Scrambling System (BISS) (Menu 4.4) BISS Mode 1 is similar to RAS in that it uses a fixed control word to encrypt the data in the transport stream.
Operating the Equipment Locally 3.9 Setting Up the T ransport S tream Output (Menu 5) 3.9.1 Set-Up Procedure Use Table 3.37 to step through the Transport Stream Output set-up procedure using Menu 5. This allows the Transport Stream for the current Service to be output on the ASI output connectors.
Operating the Equipment Locally 3.9.3 Transport Stream Output Bit-rates The Maximum input/output rates are described in Table 3.39 . Table 3.39 Maximum Descrambled Transport Stream Output Bit-rates Le.
Operating the Equipment Locally Step Action Result 6 Scroll to Menu 6.4 and edit the AUDIO 2 menu (NO ALARM, SET ALARM ONLY). Press Save . Edits the Audio 2 alarms menu. 7 Scroll to Menu 6.5 and edit the AUDIO 3 menu (NO ALARM, SET ALARM ONLY). Press Save .
Operating the Equipment Locally EN/LZT 790 0003/2 R1A 3-28 Step Action Result 6 Scroll to Menu 7.1.3.1 and edit the Subnet Mask. Press Save . Edits the Subnet Mask. 7 Scroll to Menu 7.1.3.2 and edit the Gateway address. Press Save . Edits the Gateway address.
4 Operating the Equipment Remotely Chapter 4 Contents 4.1 Remote Control .................................................................................... 4-3 4.1.1 Introduction ......................................................................
Operating the Equipment Remotely EN/LZT 790 0003/2 R1A 4-2 BLANK.
Operating the Equipment Remotely 4.1 Remote Control 4.1.1 Introduction The Multi-Format Receiver can be remotely controlled in a variety of ways. The basic control methods are: • nCompass Control .
Operating the Equipment Remotely Table 4.2 Configuring the Serial Remote Port and Activating Remote Protocol Step Action Result 1. Go to menu 7.1. Displays ‘OPERATING MODE’. 2. Press Edit . Displays ‘FRONT PANEL’. 3. Press the down pushbutto n and select ‘SERIAL REMOTE’.
Operating the Equipment Remotely However, if a situation occurs whereby the local user needs to regain control over the unit, without a local lockout relinquish command being sent from the OAC control PC, a four digit Personal Identification Number (PIN) may be entered through the keypad.
Operating the Equipment Remotely EN/LZT 790 0003/2 R1A 4-6 BLANK.
5 Alarms Chapter 5 Contents 5.1 Introduction ........................................................................................... 5-3 5.2 Location of the Alarm and Power LEDs ................................................ 5-3 5.3 Alarm LED ..
Alarms EN/LZT 790 0003/2 R1A 5-2 BLANK.
Alarms 5.1 Introduction There are two Front Panel LEDs that indicate the status of the Multi-Format Receiver. These are used to indicate abnormal performance of the unit. 5.2 Location of the Alarm and Power LEDs The red ALARM LED is used to indicate an equipment fault condition, for example a missing or faulty input signal.
Alarms EN/LZT 790 0003/2 R1A 5-4 • Audio 3 not running - This alarm is raised if the t hird audio is incorrect. • Audio 4 not running - This alarm is raised if the f orth audio is incorrect.
6 Options Chapter 6 Contents 6.1 Hardware Enabled Options .................................................................. 6-3 6.2 DVB-S2 Input Cards (RX1290/HWO/DVBS2 and RX1290/HWO/DVBS2/IF/CONST) ..................................................
Options EN/LZT 790 0003/2 R1A 6-2 List of Figures Figure 6.1 The Protocol Stack ............................................................................... 6-6 Figure 6.2 Building the Ethernet Frame.................................................
Options 6.1 Hardware Enabled Options These options require extra hardware to be fitted to the unit. Contact the Customer Services Helpdesk for details (see Preliminary Pages ). 6.2 DVB-S2 Input Cards (RX1290/HWO/DVBS2 and RX1290/HWO/DVBS2/IF/CONST) 6.
Options Table 6.1 DVB-S2 Satellite Receiver (L-band) Connector Input Specification Connector Type F-type, Female Connector designation IN 1, IN 2, IN 3, IN 4 3 x L-band inputs only on RX1290/HWO/DVBS2.
Options 6.2.4 Connector Details – Constellation Output (RX1290/HWO/DVBS2/IF/CONST) Connect the I and Q constellation output connectors to a suitable display device such as an oscilloscope set to X-Y mode. Constellation output is enabled using the Input Status Menu (Menu 2).
Options Figure 6.1 The Protocol S t ack The MPEG-2/DVB layer is specified in ISO/IEC IS 13818 – Generic Coding of Moving Pictures and Associated Audio. The UDP layer is compliant with RFC768 – User Datagram Protocol. A configurable number of 188 Byte MPEG-2 TS packets are mapped straight into an UDP frame with no additional overhead.
Options 6.5 100/1000BaseT Dual IP Input – RX1290/HWO/GIGE Dual IP NIC Input card provides a 100/1000BaseT Ethernet port, on which a transport stream can be received in UDP packets at up to 208 Mbps. The card can receive RTP encapsulated transport streams.
Options 6.5.1.2 Mode of Op eration when input port is set to Port 1 or Port 2 When the user sets the input port to either port 1 or port 2, a link down or TS lock drop does not cause any switch over to the other port. This mode of operation is the manual mode where the user decides what port is being used regardless of the status of the link.
Options 6.11 MPEG-2 HD 4:2:2 Decode (RX1290/SWO/MPEG- 2/HD/422) This option enables MPEG-2 HD 4:2:2 decode functionality. 6.12 MPEG-4 SD Decode (RX1290/S WO/MPEG4/SD) This option enables MPEG-2 HD decode functionality. 6.13 MPEG-4 HD, SD MPEG-2, HD 4:2:2 Decode (RX1290/SWO/MPEG-4/HD) This option enables H.
Options EN/LZT 790 0003/2 R1A 6-10 6.19 AAC Audio Support (RX1290/SWO/AAC) This option enables AAC audio decode support on the receiver. 6.20 Down Conversion (RX1290/SWO/DCONV) This option enables down conversion of HD to SD video on the receiver.
7 Preventive Maintenance and Fault-finding Chapter 7 Contents 7.1 Introduction ........................................................................................... 7-3 7.2 Routine Checks .........................................................
Preventive Maintenance and Fault-finding EN/LZT 790 0003/2 R1A 7-2 BLANK.
Preventive Maintenance and Fault-finding 7.1 Introduction This chapter provides the schedules and instructions, where applicable, for routine inspection, cleaning and maintenance which should be performed by an operator.
Preventive Maintenance and Fault-finding 7.3 Servicing 7.3.1 Conditions Requiring Servicing Warning! Removing the covers of this equipment may invalidate any warranties, cause a safety hazard or/and affect the EMC performance. The following is a list of conditions that may indicate the need for servicing: 1.
Preventive Maintenance and Fault-finding 7.4 Maintenance and Support Services 7.4.1 Introduction Our primary objective is to provide first clas s customer care that is tailored to your specific business and operational requirements.
Preventive Maintenance and Fault-finding 7.5 Fault-finding 7.5.1 General The information contained in this chapter is intended to isolate the unit as the faulty equipment if a system failure occurs.
Preventive Maintenance and Fault-finding 7.6 AC User Accessible Fuse Replacement Caution! This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home or business, consult your appliance dealer or local power company.
Preventive Maintenance and Fault-finding EN/LZT 790 0003/2 R1A 7-8 Caution! When replacing the power input fuse, always ensure that a fuse of the correct type and rating is fitted. Failure to do so results in inadequate protection. 3. Replace the fuse in the carrier.
A Glossary Annex A The following list covers most of the abbreviations, acronyms and terms as used in Ericsson Manuals, User and Reference Guides. All terms may not be included in this Reference Guide. μ m Micrometer (former nam e - micron): a unit of length equal to one millionth (10-6) of a meter.
Glossary AMOL I and II Automatic Measure of Line-ups I and II: Used by automated equipment to measure programme-view ing ratings. ARP Address Resolution Protocol. A protocol used to "resolve" IP addresses into underlying Ethernet MAC addresses.
Glossary Bouquet A collection of services (TV, radio, and data, or any combination of the three) grouped and sold together, and identified i n the SI as a group.
Glossary Chrominance The color part of a TV picture signal, relating to the hue and saturation but not to the luminance (brightness) of the signal. In a composite-coded color system, the color informa.
Glossary DCE Data Communications Equipment: Typically a modem. It establishes, maintains an d terminates a session on a network but in itself is not the source (originator) or destination (end receiving unit) of signals (e.g. a computer, see DTE ). A DCE device may also convert signals to comply with the tran smission path (network) format.
Glossary DSNG Digital Satellite News-Gathering. DSP Digital Signal Processor. DTE Data circuit Terminating Equipment: A communicatio ns device that originates (is the source) o r is the end receiving unit (destination) o f signals on a network. It is typically a terminal or com puter.
Glossary Encryption Encoding of a transmission to prevent access without the appropriate decryption equipment and authori zation. EPG Electronic Programme Guide: On -screen program me listing using thumbnail pictures and/or text. Ethernet The most widely used local area net work (LAN) defined by the IEEE as the 802.
Glossary GUI Graphical User Interface: The use of pictures rather than just words to represent the input and output of a program. A program with a GUI runs under a windo wing system and has a screen interface capable of displaying grap hics in the form of icons, drop-down menus and a movable poin ter.
Glossary IP Internet Protocol: The IP part of TCP/IP. IP implements the network layer (layer 3) of the protocol, which contains a network add ress and is used to route a message to a different network or sub-net work.
Glossary JPEG Joint Photographic Experts Gr oup: ISO/ITU standard for compressing still images. It has a hig h compression capability. Using discrete co sine transform, it provides use r specified compression ratios up to around 1 00:1 (there is a trade-off betwe en image quality and file size).
Glossary MEM Multiplex Element Manager: A GUI-based control system, part of the range of Ericsson AB compressi on sy stem control element produ cts. The evolution 5 000 MEM holds a model of the system hardware. Using this model, it controls the individual system ele ments to configure the output multiplexes from the incomin g elementary streams.
Glossary Multicast An IP mechanism that allows tran smission of data to multiple receivers. A multica st can also have sev eral transmit sourc es simultaneously. In video applications , mu lticast is typically used to distribute a video signal from a central source to multiple destinations.
Glossary OFDM Orthogonal Frequency Division Multiplex: A modulation techni que used for digital TV transmissi on in Europe, Japan and Australia; more spectrally efficient than FDM. In OFDM, data is di stributed over a large number of carriers spaced apart at pre cise frequencies.
Glossary PES Packetized Elementary Stream: A sequential stream of data bytes that has been converted from origin al elementary streams of audio and video access units and transpo rted as packets. Each PES packet consists of a header and a payload of variable length and subject to a maximum of 64 kbytes.
Glossary P R P B Analogue Color difference sign als. Refer to C R C B for an explanation. PROM Programmabl e Read-Only Memory: A device, which may be written once with data for permanent st orage, and then re ad whenever required.
Glossary ROM Read Only Memory: A non-volatile storage device for digital data. Data has been stored permanently in this devi ce. No further information may be stored (written) there and the data i t holds cannot be erased. Data may be read as often as required.
Glossary STB Set-Top Box: A box that sits on top of a television set and is the interface between the home television and the cable TV company. New technologies evolving for set-to p boxes are video-on-dem and, video games, educational service s, database searches, and home shopping.
Glossary SNTP Simple Network Time Protocol is an Internet protocol used to synchronize the clocks of computers to some time reference. It is a simplified version of the protoc ol NTP protocol which i s too complicated for many systems.
Glossary UART Universal Asynch ronous Receive r Transmitter: A device providing a serial interface for transmitting and recei ving data. UDP User Datagram Protocol. A protocol above the IP layer that provides port multiplexing in addition. In essence, you can transmit IP data packets to several receiving pro cesses in the same unit/device.
Glossary EN/LZT 790 0003/2 R1A A-20 Y (Luminance) Defines the brightness of a particular poi nt on a TV line. The only signal required for black and white pi ctures. Y/C Broadcast video with separate color, Y (luminance) and C (Chroma) (sometimes calle d S-Video).
B T echnical S pecification Annex B Contents B.1 Output ................................................................................................... B-3 B.1.1 Supported Video Resolutions .........................................................
Technical Specification EN/LZT 790 0003/2 R1A B-2 B.5.4 SNMP Remote Control Connector ..................................................... B-21 B.5.5 Alarm Connector ................................................................................ B-21 B.
Technical Specification B.1 Output B.1.1 Supported Video Resolutions The Multi-Format Receiver supports H.264, 4:2:0 and 4:2:2. Table B.1 Supported Video Resolut ions Input Resolutions (H x V) Frame Rates Output Format (H x V) Specification 1920 x 1080 1440 x 1080 1280 x 1080 960 x 1080 25 29.
Technical Specification Table B.3 625 Line Description Test Signal Limit Bar Level VITS17 700mV +/- 7mV Bar Tilt VITS17 <0.5% Sync Level VITS17 300mV +/- 3mV DC Offset VITS17 +/- 100mV Chrominance .
Technical Specification Description Test Signal Limit K factor K 2T NTC-7 comp <1% Pulse X bar K rating 100 +/- 1% Frequency Response (MultiBurst) FCC Multi-burst 0.5 MHz 1.25 MHz 2 MHz 3 MHz 3.58 MHz 4.1 MHz 0dB +/- 0.2 dB 0dB +/- 0.2 dB 0dB +/- 0.
Technical Specification Parameter Value for Y, R, G, B Value for Pb, Pr Condition Notes Inter-channel delay < 10 nS < 10 nS 100% color bar Interchannel crosstalk < -40 dB < -40 dB Multibur.
Technical Specification B.2 Audio Decoding and Output S tage B.2.1 General • The Multi-Format Receiver is capable of simultaneously decoding four PES streams of audio from the transport stream. Each of the decoders is identical in operation, but act completely independently of the other.
Technical Specification The Multi-Format Receiver is not able to decode and output all 5.1 channels individually as separate channels. It is possible to output the compressed Dolby Digital stream from the digital audio output, allowing it to be decoded to 5.
Technical Specification Table B.7 Analogue Audio Performance Specification s Parameter Specification Output connector Male 9 pin D-sub Output format Balanced Bit-rates 32 kbps to 38 4 kbps Sampling rates 48 KHz Nominal Output Level 0dBu +/- 0.
Technical Specification • RIGHT TO BOTH (Channel 2 on left and right) When the input signal is STEREO, the Audio digital output for mat will always be STEREO. Where a dual mono service is available, it is possible to configure the output as MIXED TO BOTH, LEFT TO BOT H and RIGHT TO BOTH.
Technical Specification Mono kbps Stereo kbps 112 224 128 256 160 320 192 384 B.3.7 Digital Audio Outputs Digital audio outputs comply with E1A-422 1 and have a maximum data rate of 3.072 Mbps. Digital audio is output on two 9-way, D-type and four BNC connectors.
Technical Specification Parameter Specification range Receive spectrum sense Normal and inverted L-band Power Input power level per carrier -65 to –25 dBm Total L-band input power < -10 dBm Oscil.
Technical Specification Parameter Specification Symbol rate step 1 Symbol/s Symbol rate lock range ± 100 ppm Maximum Channel bit-rate 90 Mbps Maximum user bit-rate 81 Mbps Es/No (C/No) ratio See Table B.
Technical Specification Table B.11 DVB-S2 Satellite Receiver Input – DVB-S Eb/No Ratio Convolutional FEC Rate Eb/No Ratio (dB) in IF Loop for correct MPEG-2 system operation 1/2 4.5 2/3 5.0 3/4 5.5 5/6 6.0 7/8 6.4 Eb/No ratio is referred to user bit-rate Ru188.
Technical Specification B.4.2 LNB Power and Control The Multi-Format Receiver provides LNB power and control signals through the active RF input connector. LNB power and controls are enabled through t he Satellite Input Menu, see Annex C, Menus . The Multi-Format Receiver supports voltage controlled LNBs only.
Technical Specification Input Specification De-Interleaver On/Off, Not available in 188-packet mode Status LED Gree n: Lock, Red: No Lock Output Connector Not in use B.4.4 DVB-ASI Input Table B.15 DVB-ASI Copper Input Specification Safety status SELV Connector type BNC, Female Input impedance 75 Ω Data rate range 0.
Technical Specification Input Specification Duplex mode Data Rate 1.5 – 208 Mbps TS CBR MPTS/SPTS feeds Error correction Pro MPEG FEC B.4.7 Frame Sync Connector The Decoder can frame lock to an external video source. The frame information is input as a composite synchronous signal, with or without active video.
Technical Specification B.5.1.2 Digital Video Table B.20 Digital Video Output Connectors Item Specification Safety status SE LV Connecto r type BNC, Fem ale, 75 Ω Connector designation HD SDI 1 HD SD.
Technical Specification Description Test Signal Limit Weighted Luminance Noise Luminance Ramp <60 dB Weighted Luminance Noise Flat Grey Field <63 dB Chrominance PM Noise Flat Red Field <55 dB Table B.22 525 Line Description Test Signal Limit Bar Level NTC-7 comp 100 IRE +/- 1 IRE Bar Tilt NTC-7 comp <0.
Technical Specification B.5.2 Audio Outputs Table B.23 Digital (Unbalanced) Audio Connectors Item Specification Connecto r type BNC 75 Ω socket Connector designation AUD 1, AUD 2, AUD 3 and AUD 4 Pin-outs Centre Shield Digital Audio output (AES/EBU) Ground/Chassis Table B.
Technical Specification B.5.3.2 High Speed Data over Ethernet This connector is located at the back of the unit using the RJ-45 Ethernet port and is enabled through the license key (RX1290/SWO/HSETHER).
Technical Specification Item Specification Maximum Switching Power 24 W / 60 VA Minimum Switching Load 0.1 mA, 100 mV DC B.6 Environment al B.6.1 Conditions Table B.
Technical Specification B.8.1 EMC 9 The equipment has been designed and tested to meet the following: EN 55022 and CISPR22 European International Emission Standard Limits and methods of measurement of radio frequency interference characteristics of information technology equipment - Class A.
Technical Specification COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.
Technical Specification The packaging is reusable per GB 18455-2001. This symbol guarantees that packagi ng with this symbol is recyclable and will be accepted by cardboard recyclers. Recyclable per GB 18455-2001. B.8.7 Materials Declarations Ericsson’s products are designed and manufactured in keeping with good environmental practice.
Technical Specification It is assumed that while the product is in normal use, any batteries associated with real-time clocks or battery-backed RAM will be replaced at the regular in tervals. The EFUP relates only to the environmental impact of the product in normal use, it does not imply that the product will continue to be supported for 50 years.
Technical Specification • Company • Work Area (select one of the below) - Executive Management - Marketing and Sales - Planning/Engineering - Procurement/Supply - Project & Programme - Impleme.
Technical Specification EN/LZT 790 0003/2 R1A B-28 BLANK.
C Menus Annex C Contents C.1 LCD Menus .......................................................................................... C-5 C.1.1 Using the Menus .................................................................................. C-5 C.1.2 Menu Descriptions .
Menus C.9.1 Overview ............................................................................................ C-20 C.9.2 Transport Stream Alarm Setup Menu................................................. C-21 C.9.3 Video Alarm Setup Menu .........
Menus Table C.34 MER Alarm Setup Menu .................................................................... C-23 Table C.35 C/N Alarm Setup Menu ...................................................................... C-23 Table C.36 Temperature Alarm Setup Menu .
Menus EN/LZT 790 0003/2 R1A C-4 BLANK.
Menus C.1 LCD Menus C.1.1 Using the Menus Detailed description of the use of menus is given in Chapter 3, Operating the Equipment Locally . C.1.2 Menu Descriptions This annex describes the front panel LCD menus. When the unit is first powered up, it progresses through a se ries of start-up pages on the LCD display.
Menus C.3 The Menu S tructure Figure C.1 Menu S tructure Switch ON Boot Screen 1 Preset Menu 2 Input Menu 3 Service Menu 4 Conditional Access Menu 5 TS Output Menu 6 Alarms Menu 7 System Menu 7 Date/Time 7.1 Setup Operating Mode 7.1.1 LCD Contrast 7.1.
Menus C.4 Presets Menu Items (Menu 1) The Presets menu contains up to 40 editable preset numbers in the range 01 – 40. Selecting a Service via the Presets menu automatically reconfigures the input of the Multi-Format Receiver. Each preset can have a selected language, network name and service provider associated with it.
Menus Table C.4 Input Selection Menu Display Title: Input Description Select XXXX XXXX is the editable input source selection (ASI, SMPTE 310, any option cards). C.5.3 DVB-S2 Option DVB-S2 Input Option (RX1290/HWO/DVBS2 or RX1290/HWO/DVBS2/IF/CONST) When a DVB-S2 interface is used, the Input menu allows the user to edit the parameters.
Menus T able C.6 TTV G .703 Menu Display Title: Input Description STATUS PDH Rate XXXXX XXXXX is the framing mode of the TTV G.703 input module (None, C-Bit, M13) RANDOMISATION XXXX STUFFING PKTS YYYY XXXX (ACTIVE, NOT ACTIVE) YYYY (PRESENT, NOT PRESENT) SETUP REED-SOLOMON DECO DER XXXXX XXXXX is the EDITABLE Reed-Solom on option.
Menus C.5.6 100/1000BaseT Dual IP NIC Input Option Menu When a 100/1000BaseT input interface is used, the Input menu allows the user to edit the set-up parameters.
Menus Menus EN/LZT 790 0003/2 R1A C-11 EN/LZT 790 0003/2 R1A C-11.
Menus C.6 Conditional Access Menu C.6.1 Overview The CA Menu allows the user to enter the various keys required for the different scrambling modes. C.6.2 RAS Mode Allows the user to select between DSNG KEY MODE and FIXED KEY MODE Table C.8 RAS Mode Menu Display Description CA RAS DSNG KEY MODE KEY XXXXXXX XXXXXXX is the DSNG Key C.
Menus Director 5 Display Description NCP Lock Override PIN XXXX XXXX is PIN code RESET Lock Override PIN XXXXXXXXXXXXX XXXXXXXXXXXXX is PIN code NCP EXTENDED TIMEOUT XXXX XXXX enabled/disabled POWER UP CARRIER XXXX XXXX is clear carrier slot EMERGENCY HOME CARRIER XXXX XXXX is clear carrier slot C.
Menus After making a selection (in EDIT mode using page 1), and selecting the required component data streams (using the other pages), pressing SAVE makes it the current service. The audio and data modules will decode according to the default parameters set in other pages.
Menus T able C.14 Video Menu Display Title: Video Description XX Stream PID ZZZZ YYYY XX is the number of video streams ZZZZ is the currently selected video stream PID YYYY is the currently selected video st ream status (OK, STOP, FAIL) Resolution XXXXXXXXX Frame Rate YY.
Menus Display Title: Video Description Embedded Audio ID Group Group 1,2,3 or 4 525 Line Output NTSC-M, PAL-M, NTSC-MNP 625 Line Output PAL-B/G/I, PAL-N,PAL-N CMB C.7.3 Audio 1 Menu The Audio 1 signal status submenu contains inf ormation about the audio format and status of the currently decoded audio stream on the primary audio output.
Menus Display Title: Audio 02 Description WWWWWWW is the audio language Sampling Rate XX.X kHz Bit-rate YYY kbit/s XX.X is the Audio 2 sample rate YY is the Audio 2 bit-rate Rate Buffer Level Audio 2 percentage rate buffer level Delay Adjustment XXX.X ms XXX.
Menus T able C.18 Audio 4 Menu Display Title: Audio 02 Description XX Streams PID YYYY WWWW WWWW W VVV ZZZZ XX is the number of Audio streams present YYYY is the currently selected audio4 PID ZZZZ is the stream status (OK, STOP, FAIL) VVV is the audio layer (MUS, LIN, DD) WWWWWWW is the audio language Sampling Rate XX.
Menus T able C.20 High Speed Data Over Ethernet Menu Display Title: Ethernet Data Description User PID XXXX YYY PIPE ZZZZ XXXX is the currently selected HSD PID YYY is the stream status (PRESENT, NOT PRESENT) ZZZZ is the status of the service (OK, STOP, FAILED) Bit-rate X.
Menus T able C.23 Network ID Menu Display Title: Network ID Description Network ID XXXXX Original Network ID YYYYY XXXXX is the network ID from the cu rrent SDT (or - ---- when SDT not available) YYYYY is the original network ID fr om the current SDT (or ----- when SDT not available) C.
Menus T able C.26 Alarms Menu Display Title: Alarms Description Section Transport Stream Alarm Setup Transport Stream alarm and relay settings. C.9.2 Video Alarm Setup Video alarm and relay settings. C.9.3 Audio 1 Alarm Setup Audio 1 ala rm and relay settings.
Menus C.9.5 Audio 2 Alarm Setup Menu T able C.30 Audio 2 Alarm Setup Menu Display Title: Description IF AUDIO 02 NOT RUNNI NG YYYYYYYYYYYYYY YYYYYYYYYYYYYY is editable: NO ALARM SET ALARM ONLY C.
Menus C.9.9 MER Alarm Setup Menu Table C.34 MER Alarm Setup Menu Display Title: Description IF MER LESS THAN XX.X YYYYYYYYYYYYYY YYYYYYYYYYYYYY is editable 0 to 69.9: NO ALARM SET ALARM ONLY C.9.10 C/N Alarm Setup Menu Table C.35 C/N Alarm Setup Menu Display Title: Description IF C/N LESS THAN XX.
Menus Display Title: Setup Description XXXXXXXXXXXXX FRONT PANEL SERIAL REMOTE (not supported in software version 1.0.0) NETWORK (SNMP) LCD Contrast XXXXXX XXXXXX is ed itable in the range: LOW MEDIUM.
Menus Display Title: CR Details Description XX.XX.XX Firmware Versions XX.XX XX.XX is the firmware 1 version number XX.XX is the firmware 2 version number Hardware Version XXXX XXXX is the hardware version number PLD Versions XXXX XXXX is the PLD 1 version number XXXX is the PLD 2 version number Tempera ture XX.
Menus EN/LZT 790 0003/2 R1A C-26 BLANK.
D Language Abbreviations Annex D Contents D.1 ISO Language Abbreviations ............................................................... D-3 D.2 Non-ISO Languages ............................................................................ D-3 List of Tables Table D.
Language Abbreviations EN/LZT 790 0003/2 R1A D-2 BLANK.
Language Abbreviations D.1 ISO Language Abbreviations Languages are shown in alphabetical order. T able D.1 ISO Language Abbreviation T able No Language Abbreviation No Language Abbreviation 5 ARABIC .
Language Abbreviations EN/LZT 790 0003/2 R1A D-4 Table D.2 Non-ISO Language Abbreviation Table Language Abbreviation MAIN ONE AUX TWO INTERNATIONAL SOUND INT AUDIO 1 AAA AUDIO 2 AAB AUDIO 3 AAC AUDIO .
Factory Defaults E Factory Defaults Annex E Units are shipped with the following factory default parameters. These can be restored at any time using the System Menu. All other parameters ar e unaffected by restoring the factory defaults. Menu Description Default #2 Input SELECT INPUT ASI SOURCE 1 LNB FREQUENCY 10750.
Factory Defaults Menu Description Default ARP On SNMP Off FEC On if licensed UDP Upgrade port 61111 IP de-jitter Buffer Level 60ms Redundancy mode Use Input Port 1 Auto Revert Delay 0 Mcast IP Address.
Factory Defaults Menu Description Default ASYNC DATA ENABLED SYNC DATA (High Speed Ethernet Data Not Fitted) ENABLED ETH.NET DATA (High Speed Ethernet Data Fitted) ENABLED VITC INSERTION ENABLED CLOSE.
Factory Defaults EN/LZT 790 0003/2 R1A E-4 Menu Description Default SW VERSION/ FW VERSION/ HW VERSION/ PLD VERSION/ ELECTRONIC SERIAL NUMBER UNAFFECTED.
An important point after buying a device Ericsson RX1290 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ericsson RX1290 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ericsson RX1290 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ericsson RX1290 you will learn all the available features of the product, as well as information on its operation. The information that you get Ericsson RX1290 will certainly help you make a decision on the purchase.
If you already are a holder of Ericsson RX1290, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ericsson RX1290.
However, one of the most important roles played by the user manual is to help in solving problems with Ericsson RX1290. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ericsson RX1290 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
