Instruction/ maintenance manual of the product Dishwasher Alliance Laundry Systems
Go to page of 24
Para bajar una copia de estas instrucci ones en español, visite www.comlaundry.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Inst allation Instructions for S t acked W ashers and Dryers Dimensions .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 2 802715 IMPOR T ANT : Purchaser must consu lt the local gas supplie r for suggested instructions to be followed if the unit user smells gas.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 3 Dimensions SWD897N * With leveli ng legs turned into base. NOTE: Exhaust op enings are 4 inch (10.2 c m) metal ducting. SWD898N *With leveling legs turned into base. NOTE: Exhaust op enings are 4 inch (10.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 4 802715 Before Y ou St art Supplies For most installations, the basic supplies you will need are: Figure 1 NOTE: If the unit i.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 5 Inst allation Step 1: Position Unit Near Inst allation Area Move unit as close to the desired area of installation as possible. NOTE: For best performance and to minimize vibration or movement, install washer on a solid, sturdy and level floor .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 6 802715 NOTE: Use of the dispenser drawer or unit doors as a handle in the transportation of the unit may cause damage to the dispenser or doors. Place unit in position on a soli d, sturdy and level floor .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 7 Step 3: Connect Fill Hoses Wat e r Su p p l y W ater supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 8 802715 IMPOR T ANT : Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperatur e and constant high pressur e they are subject to.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 9 Step 4: Connect Drain Hose to Drain Recept acle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose f rom the retainer clamp and by removing th e shipping tape.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 10 802715 Step 5: (Gas Dryer Only) Connect Gas Supply Pipe 1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 inch NPT gas connectio n.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 11 4. T ighten all connections securely . T urn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection fluid.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 12 802715 Grounding Information • This dryer must be con nected to a grounded metal, permanent wiring system; or an equipment-grounding cond uctor must be run with the circuit conducto rs and connected to the equipment-grounding term inal or lead on the dryer .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 13 Connecting Power Cord with Three-Wire Plug NOTE: Four -wire cord is requir ed for mobile homes or where codes do not permit grounding through neutral. Figure 12 1. Disconnect power to dryer .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 14 802715 4. Use the three screws from the accessories bag to attach the power cord wir es to the terminal block.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 15 3. Remove ground screw and save for use in S tep 5. Remove wire and use in Step 6. Figure 18 4. Use a strain relief and insert end of power cord through power suppl y hole.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 16 802715 Step 7: Connect Dryer Exhaust System • DO NOT use plastic or thin foil ducting. Rigid metal duct is recommended. Refer to Figur e 21 . • Locate dryer so exhaust duct is as short as possible.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 17 Exhaust Direction The dryer can be exhausted to the ou tdoors through the back, left, right or bottom of the dryer . EXCEPT ION: Gas dryers cannot be vented out the left side because of the burner housing.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 18 802715 Step 8: (W asher On ly) Remove th e Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws at the bottom of the panel. Remove the five bolts an d lockwashers from shipping brace with 9/16 inch wrench and remove brace.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 19 Step 10: Plug In the W asher and Dryer Electric Dryer Connect the dryer to an electrical pow er source.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 20 802715 Washer - All Models Except L TSA7A*N2989 W asher requires 120 V olt, 60 Hertz e lectrical supply and comes equipped with a 3-prong grou nding plug. Refer to serial plate for specific electrical requirements.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 21 When plugging in the washer: • DO NOT overload circuits. • DO NOT use an extension cord. • DO NOT use an adapter . • DO NOT operate both a washer and gas dryer on the same circuit.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 22 802715 After the dryer has operated fo r approximately five minutes, observe burn er flame through lower front panel. Adjust the air shutte r to obtain a soft, uniform blue flame.
.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT Inst aller Checklist Fast T rack for Inst alling the Unit (Refer to the manual for mor e detailed information) • Position Unit Near Installation Are a. 1 CHECK • Position and Level the Unit.
An important point after buying a device Alliance Laundry Systems Dishwasher (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alliance Laundry Systems Dishwasher yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alliance Laundry Systems Dishwasher - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alliance Laundry Systems Dishwasher you will learn all the available features of the product, as well as information on its operation. The information that you get Alliance Laundry Systems Dishwasher will certainly help you make a decision on the purchase.
If you already are a holder of Alliance Laundry Systems Dishwasher, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alliance Laundry Systems Dishwasher.
However, one of the most important roles played by the user manual is to help in solving problems with Alliance Laundry Systems Dishwasher. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alliance Laundry Systems Dishwasher along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
