Instruction/ maintenance manual of the product MLC 104 IP Plus Epson
Go to page of 26
© 2006 Extron Electronics. All rights reserved. Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Extron Electronics, E urope Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.
Pr ecautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压，有触电危险。 .
i MLC 104 IP Plus • T able of Contents T able of Contents Chapter One • Introduction ................................................... 1-1 About this Manual .................................................................... 1-2 About the MLC 104 IP Plus Medialink ™ Controllers .
ii MLC 104 IP Plus • T able of Contents T able of Contents, cont’d MLC 104 IP Plus 1 Chapter One Intr oduction About this Manual About the MLC 104 IP Plus MediaLink Controllers About Global Configurator System Requirements Installing the Software Updating Firmware Step 11 : Build and Upload a Configuration .
MLC 104 IP Plus • Introduction Intr oduction MLC 104 IP Plus • Introduction 1-2 1-3 A typical application for an MLC 104 IP Plus Medialink Controller About Global Configurator The Extron Global C.
MLC 104 IP Plus • Introduction Introduction, cont’d 1-4 MLC 104 IP Plus • Introduction 1-5 Global Configurator provides the following featur es for the MLC 104 IP Plus: Offline configuration .
MLC 104 IP Plus • Introduction Introduction, cont’d 1-6 MLC 104 IP Plus 2 Chapter T wo MLC 104 IP Plus Har dware Setup Right Side Panel Features and Connections Left Side/T op Panel Features and C.
MLC 104 IP Plus • Hardwar e Setup Har dware Setup MLC 104 IP Plus • Hardwar e Setup 2-3 2-2 This chapter describes right, left, and front panel featur es; basic front panel operation; and how to connect cables to the MLC 104 IP Plus contr oller .
MLC 104 IP Plus • Hardwar e Setup Hardwar e Setup, cont’d 2-4 MLC 104 IP Plus • Hardwar e Setup 2-5 MLC 104 IP Plus Right Side Panel COMM LINK A B C D E +V OUT GROUND CM IR IN SCP E C B A SCP co.
MLC 104 IP Plus • Hardwar e Setup Hardwar e Setup, cont’d 2-6 MLC 104 IP Plus • Hardwar e Setup 2-7 Both digital input and output modes of the digital I/O ports have the ability to turn on an internal pull-up resistor to + 5 VDC (equivalent to SW2 on the previous illustration).
MLC 104 IP Plus • Hardwar e Setup Hardwar e Setup, cont’d 2-8 MLC 104 IP Plus • Hardwar e Setup 2-9 Left Side/T op Panel Features and Connections RESET MLC 104 IP Plus Left Side 1 a Reset button and LED — Pressing this r ecessed button causes various IP functions and Ethernet connection settings to be r eset to their factory defaults.
MLC 104 IP Plus • Hardwar e Setup Hardwar e Setup, cont’d 2-10 MLC 104 IP Plus • Hardwar e Setup 2-11 Front Panel Featur es and Basic Operation There ar e several features that must be set up prior to using the MLC. Refer to chapter 4 in the MLC 104 IP Plus User's Manual for details.
MLC 104 IP Plus • Hardwar e Setup Har dware Setup MLC 104 IP Plus 2-12 3 Chapter Thr ee MLC 104 IP Plus Softwar e Setup Step 1: Download Device Drivers Step 2: Create a New Project Step 3: Add an ML.
MLC 104 IP Plus • Software Setup Softwar e Setup MLC 104 IP Plus • Software Setup 3-2 3-3 This chapter provides the steps for setting up your MLC 104 IP Plus contr oller using the Global Configurator (GC) software. By means of example, you will learn how to • Add drivers that allow control of A/V devices.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-4 MLC 104 IP Plus • Software Setup 3-5 Step 2 : Create a New Pr oject 1. If the GC 2 Start Options dialog is displayed, select the "Create a New Pr oject" option and click the O K button.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-6 MLC 104 IP Plus • Software Setup 3-7 Add Device dialog box (Advanced) 5. Select the Auto Configure IP Address check box. The MAC Address text box becomes active and the first three octets of the MAC address appear .
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-8 MLC 104 IP Plus • Software Setup 3-9 4. Complete each of the fields with your mail server IP address , mail server domain , and, if necessary , your user name and password . 5. Click the OK button.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-10 MLC 104 IP Plus • Software Setup 3-11 Step 5 : Add a Serial and an IR Device Adding an A/V device (projector displays, VCRs, DVDs, etc.) for an MLC to control r equires that you first add the device’s driver to the GC configuration.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-12 MLC 104 IP Plus • Software Setup 3-13 Adding an IR driver T o add an IR driver to a port: 1. From the IP Link tab (left pane), select the IR port labeled Port A beneath the MLC 104 IP Plus tr ee.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-14 MLC 104 IP Plus • Software Setup 3-15 4. Drag the On icon to the right-side window field labeled Release . This sets the command to activate on the release of the button. N Failure to configur e the On or Off buttons on Release may cause problems with the PIN Mode featur e.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-16 MLC 104 IP Plus • Software Setup 3-17 Control module main window 4 . Select the Address #1 tab. The Address 1 IRCM-DV+ [DVD] window appears. 5. In the upper left corner drop-down menu (under DVD & VCR Control ), select Input 2 , as illustrated below .
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-18 MLC 104 IP Plus • Software Setup 3-19 Step 8 : Create a Display Shutdown Schedule Global Configurator ’s (GC) scheduling featur e enables you to schedule actions and events for a selected device.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-20 MLC 104 IP Plus • Software Setup 3-21 Step 9 : Create a Display Lamp Hour W ar ning E-mail Global Configurator ’s monitoring featur e enables you to configure an MLC 104 IP Plus controller to monitor many parameters of the connected display devices.
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-22 MLC 104 IP Plus • Software Setup 3-23 Step 10 : Create a Display Disconnection E-mail T o set a display disconnected e-mail alert, do the following: 1 . Click the Monitor tab in the Global Configurator window .
MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-24 T o begin the upload, do the following: 1 . Click Begin . The Upload Manager monitors the progr ess of the upload. 2 . When the upload is finished, click Close . The configuration should now be successfully uploaded to the appropriate pr oduct(s).
An important point after buying a device Epson MLC 104 IP Plus (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson MLC 104 IP Plus yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson MLC 104 IP Plus - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson MLC 104 IP Plus you will learn all the available features of the product, as well as information on its operation. The information that you get Epson MLC 104 IP Plus will certainly help you make a decision on the purchase.
If you already are a holder of Epson MLC 104 IP Plus, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson MLC 104 IP Plus.
However, one of the most important roles played by the user manual is to help in solving problems with Epson MLC 104 IP Plus. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson MLC 104 IP Plus along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
