Instruction/ maintenance manual of the product 7600 Epson
Go to page of 11
EPSON Stylus ® Pro 7600/9600 Quick Refer ence Guide EPSON Stylus ® Pro 7600/9600 Printed in USA CPD-14020.
1 Slide the remo vable paper stop off the left end of the spindle. T o use a 3-inch roll paper core, attach the gray adapters to the paper stops at each end. See your Printer Guide for details. 2 P osition the r oll paper as shown, then slide it onto the spindle.
2 4 F eed the sheet into the paper slot. Make sure the right edge of the paper is straight and aligned with the scale on the roll paper co ver . F or a large sheet of paper , feed it so that it comes out below . Then align the edges of the sheet with the rows of holes as sho wn.
3 6 Align the board with the scale on the roll paper cover . 4 Open the front co ver . (The cover has special tabs that act as paper supports when the cover is open.) 5 F eed the posterboard into the paper slot until it meets resistance. If you ’ re using stock more than 39 inches long, load it long edge first (in landscape orientation).
4 If you notice banding or missing colors in your printouts, the print head may need cleaning. F irst print a nozzle check pattern to find out the condition of the print head. Then run a cleaning cycle, if neccessary , and print another check pattern to test the results.
5 5 Continue ▲ Before you begin a large print job , you should check your ink levels. If one of your cartridges is lo w , you can replace it before y ou start. Or you can wait until the ink runs out, replace the cartridge, and then continue the job without any loss of print quality .
6 When one of the Ink Out lights stays on and INK OUT is displayed on the control panel, the cartridge is empty . T o replace the cartridge, first make sure the printer is on. 1 Open the ink compartment cov er . 2 Raise the ink lever to the unlocked position.
7 Replacing the Cutter Blade If you notice that the paper isn ’ t cut cleanly , you may need to replace the cutter blade. Y ou can check its status as described below: 1 P ress the SelecT ype button on the control panel, then press until you see PRINTER ST A TUS .
Message Light Explanation or response READY Operate light on Printer is ready to print. PRINTING Operate light flashing Printer is receiving data. RESET All lights flash briefly Printer is resetting. PRESS P AUSE BUTTON Pause light on Press the Pause button to continue.
Where T o Get Help Where T o Get Help 9 Message Light Explanation Response P APER JAM Paper Out light Paper has jammed in the Raise the paper lever and open flashing printer . the lower cover if necessary . Then remove the jammed paper , close the lower cover , and lower the lever .
E P S O N S t y l u s ® P r o 7 6 0 0 / 9 6 0 0 Quick Reference Guide CPD14020R1_Baf_QRG.qx 9/17/03 5:31 PM Page 1.
An important point after buying a device Epson 7600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson 7600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson 7600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson 7600 you will learn all the available features of the product, as well as information on its operation. The information that you get Epson 7600 will certainly help you make a decision on the purchase.
If you already are a holder of Epson 7600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson 7600.
However, one of the most important roles played by the user manual is to help in solving problems with Epson 7600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson 7600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
