Instruction/ maintenance manual of the product Matrix DFE-Gold Series Enterasys
Go to page of 944
P/N 9033933-15 Enterasys Matrix ® DFE-Gold Configuration Guide Firmware V ersion 6.11.xx.
.
i Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web si te without prior notice.
ii Enterasys Networks, Inc. Software Li cense Agreement This document is an agreement (“ Agreement”) betw een Yo u , the end user , and Enterasys Networks, Inc.
iii 5. PROTECTION AND SECURITY .I n the performance of this Agreement or in contemplation thereof, You and your employees and agents.
iv 9. UNITED STATES GOVERNMENT RESTRICTED RIGHTS .T h e Licensed Mate rials (i) were de veloped solely at private expense; (ii) contains “restricted computer software” submitted with restri cted rights in accordance with section 52 .
v Contents About This Guide Using This Guide ................ ............. ................ ............. ................ ............. ................ ....... ......................... ...xxxiii Structure of This Guide ....... ................ ...
vi clear ip gratuitous-arp ................ ............. ................ ................ ............. ................ ............. . ............... 2-33 show system ....... ................. ............. ............ ............. ............
vii set inlinepower psetra p ................. ............. ............. ................ ............. ............. ............. ...... ............. 2-69 clear inlinepower psetrap ........................ ............. ................ .........
viii Purpose ........... ............. ............. ............. ............ ................. ............. ............ ............. .. ..................... .... 2-101 Commands ............... ............. ................. ............ ......
ix clear lldp port trap ......... ............. ............. ................ ............. ................ ............. ............. . .................. 3-35 clear lldp port med-trap ..................... ............ ................. .........
x Purpose ........... ............. ............. ............. ............ ................. ............. ............ ............. .. ..................... ...... 4-27 Commands ............... ............. ................. ............ ........
xi show lacp ... ............. ................ ............. ............. ............. ................ ............. ............. ..... .................... 4-58 set lacp ................... ............. ............. ............ ..............
xii show snmp context ....... ................ ............. ............. ................ ............. ................ ............. ... ............. 5-23 set snmp view ............ ................ ............. ................ ............. ..
xiii show spantree vlanlist . ........ ............. ............ ................. ............. ............ ............. ................ .......... ... 6-16 show spantree mstcfgid ....... ............. ................ ............. .............
xiv clear spantree newroottrapenable .......... ............. ................ ............. ................ ................ ........... ..... 6-45 clear spantree default ...... ................. ............ ................. ............. ........
xv show spantree nonforwardingreas on ........ ............. ............. ................ ............. ............. ............. ..... .6 - 7 7 Chapter 7: 802.1Q VLAN Configuration VLAN Configuration Summary ........................... ..........
xvi Purpose ........... ............. ............. ............. ............ ................. ............. ............ ............. .. ..................... ........ 8-2 Commands ............... ............. ................. ............ .....
xvii show route-map ............ ............. ............. ................ ............. ............. ................ ............. .... ............... 8-42 route-map ............... ............. ............. ................ ............. ...
xviii set logging application ..... ............. ................ ............. ................. ............ ............. ............... ..... ......... 10-9 clear logging application ...... ................ ............. ............. ..........
xix set rmon matrix properties ...... ................ ............. ................ ............. ................ ............. ........ ......... 11-34 set rmon matrix status ............ ................ ............. ................ ...........
xx Chapter 14: Node Alias Configuration Configuring Node Aliases ... ... ...... ................. ............ ............. ............. ................ ............. ...... .................... ... 14-1 Purpose ........... ............. ..........
xxi Reviewing and Configuring the ARP Table ........... ............. ................ ............. ............. ............. ........ ......... 16-12 Purpose ........... ............. ............. ............. ............ ................. ....
xxii Chapter 18: Network Address Tran slation (NAT) Configuration Configuring Network Address Transl ation (NAT) ...................... ............. ................ ............. ................ . ........ 18-1 NAT Configuration Task List and C ommands .
xxiii show ip slb conns ............ ............. ................ ............. ................. ............ ............. .............. ......... .... 19-29 show ip slb stats ........ ................ ............. ............. ................
xxiv accept-lifetime ........ ............. ............. ................ ............. ............. ............ ................. ....... ............... . 21-10 send-lifetime ....... ............. ............. ................ ............. ....
xxv Configuring IRDP ... ................ ............. ................ ............. ............. ................ ............. ....... ............... ........... 21-55 Purpose ........... ............. ............. ............. ............ ..
xxvi cache ............... ............. ............. ................ ............. ............. ................ ............. .......... ................ ...... 23-5 faildetect type ......................... ................ ............. .......
xxvii show access-lists ....................... ............. ............. ................ ............. ................ ............. ... .............. 24-15 access-list (standard) ................ ................ ............. ............. ...
xxviii set pwa enhancedmode ...................... ............. ................ ............. ................ ............. .............. ...... 25-20 set pwa guestname ...................... ............. ............. ................ ..........
xxix set authentication login .............. ............. ................ ............. ................ ............. ................ .. ............ 2 5-51 clear authentication login ........... ................ ............. ................ ...
xxx clear multiauth mode .............. ............. ................ ............. ................ ................ ............. ...... ............. 27-3 show multiauth ..................... ............. ................ ............. ..........
xxxi 4-3 show port advertise Output Details ............... ................. ............. ................ ............. ............ .... ......... 4-34 4-4 show port flow cont rol Output Details .................. ............. ............. .....
xxxii 19-1 LSNAT Configuration Task List and Commands . ................ ................ ................ ................ ............. 19- 5 19-2 show ip slb reals Output Details ....... ......... ... ................. ............. ............ ..
Enterasys Matrix DFE-Gold Series Configuratio n Guide xxxiii About This Guide This manual explains how to access the device’ s Command Line Interface (CLI) and how to use it to configure Enterasys Matrix ® DFE ‐ Gold Series switch/router devices.
Structure of This Guide xxxiv About This Guide Protocol, the Cisco Discov ery Protocol, and the IEEE 802.1AB Link Lay er Discov ery Protocol (LLDP) and LLDP Media Endpoint Discov ery Protcol (LLDP ‐ MED).
Related Documents Enterasys Matrix DFE-Gold Series Configuration Gu ide xxxv Chapter 20 , DHCP Configuration , describes how to configure and display statistics for Dynamic Host Configuration Protocol.
Conventions Used in This Guide xxxvi About This Guide Conventions Used in This Guide The following conventions are used in the text of this document: The fo.
Getting Help Enterasys Matrix DFE-Gold Series Configuration Guide xxxvii Getting Help For additional support re lated to the product or this document, contact .
Getting Help xxxviii About This Guide.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 1-1 1 Introduction This chapter provides an overview of the Enterasys Matrix Series’ unique features.
Device Management Methods 1-2 Introduction • Configure the device to operate as a Generic Attribute Registration Protocol (GARP) de vice to dynamically create VLANs across a switched network.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 2-1 2 S tartup and General Configuration This chapter descri bes factory default settings and the Startup and General Configuration set of commands.
Startup and General Configuration Summary 2-2 Startup an d General Configuration T able 2-1 Default Device Settings f or Basic Switch Operation Device Feature Default Setting CDP discovery protocol Auto enabled on all ports. CDP authentication code Set to 00-00-00-00 -00-00-00-00 CDP hold time Set to 180 seconds.
Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuration Gu ide 2-3 MAC aging time Set to 300 seconds. MAC locking Disabled (globall y and on all ports). Management Authentication Notifi cation Enabled MTU discovery protocol Enabled.
Startup and General Configuration Summary 2-4 Startup an d General Configuration S panning Tree edge port delay Enabled. S panning Tree forward delay Set to 15 seconds. S panning Tree hello interval Set to 2 sec onds. S panning Tree ID (SID) Set to 0 .
Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuration Gu ide 2-5 VLAN ID All ports use a VLAN id entifier of 1 . WebV iew (HTTP) Enabled on TCP port 80. T able 2-2 Default Device Settings f or Router Mode Operation Device Feature Default Setting Access groups (IP security) None confi gured.
Startup and General Configuration Summary 2-6 Startup an d General Configuration CLI “Default s” Descriptions Each command description in this guide includes a sect.
Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuration Gu ide 2-7 Using W ebV iew By default We b V i e w (Enterasys Networks’ embedded web .
Startup and General Configuration Summary 2-8 Startup an d General Configuration 3. Leave this string blank and press ENTER. The device information and Matrix prompt displays as shown in Figure 2 ‐ 1 .
Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuration Gu ide 2-9 (c) Copyright Enterasys Networks, In c. 2005 ModuleChassis Serial Number: 1234567 ModuleChassis Firmware Revision: 05.
Startup and General Configuration Summary 2-10 Startup a nd General Configuration remote Show users with r emote SNMP engine ID volatile Show temporary en tries nonvolatile Show permanent en tries rea.
Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-11 Abbreviating and Completing Co mmands The Matrix Ser ies device allows you .
Startup and General Configuration Summary 2-12 Startup a nd General Configuration Ctrl+E Move cursor to end of line. Ctrl+F Move cursor forward one character . Ctrl+H Del ete character to left of cursor . Ctrl+I or T AB Complete word. Ctrl+K Delete all characters after cursor .
show line-editor Startup and General Configuration Summary Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-13 Commands show line-editor Use this command to show current and default line ‐ editor mode and Delete character mode.
Startup and General Configuration Summary set line-editor 2-14 Startup a nd General Configuration set line-editor Use thi s command to set the current and def ault line editing mode or the wa y the Delete character is treated by the line editor .
show system login Setting Use r Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-15 Setting User Account s and Passwords Purpose To change the device’ s default user login and passw ord settings, and to add new user accounts and passwords.
Setting User Accounts and Passwords set system logi n 2-16 Startup a nd General Configuration admin super-user enabled no ***access always allowed*** bar read-only enabled yes 00:00 24:00 Sun Sat foo .
clear system login Setting User Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-17 Default s allowed ‐ interv al: 00:00 ‐ 24:00 (all hours allowed) allowed ‐ days: Sun, Mo n, Tu e , We d , Thu, Fri, Sat (all days allow ed) local ‐ only: no.
Setting User Accounts and Passwords set password 2-18 Startup a nd General Configuration Default s The account is removed if no optional parameters are entered.
show system password Setting User Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-19 The admin passw ord can be reset by toggling dip switch 8 on the device as des cribed in your Matrix Series Installation Gu ide .
Setting User Accounts and Passwords set system password 2-20 Startup a nd General Configuration Numeric: 0 Special: 0 Password assignment required at acco unt creation : no Allow multiple accounts to .
set system password Setting User Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-21 Default s aging = disable history = 0 passw ords length = 8 characters min ‐ requir ed ‐ chars = 0 characters for all cases require ‐ at ‐ creation = No .
Setting User Accounts and Passwords clear system password 2-22 Startup a nd General Configuration If the require ‐ at ‐ creation option is enabled, the set system .
show system lockout Setting User Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-23 Default s If no options are specified, options are rese t to default va l u e s . Mode Switch comman, Super User .
Setting User Accounts and Passwords set system lockout 2-24 Startup a nd General Configuration Ta b l e 2 ‐ 4 provides an explanation of the command output.
set system lockout Setting User Accounts and Passwords Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-25 Example This example shows how to set login attempts t.
Managing the Management Authentication Notification MIB show mgmt-auth-notify 2-26 Startup a nd General Configuration Managing the Management Authentication Notification MIB Purpose This MIB p.
set mgmt-auth-notify Managing the Management Authentication Notification MIB Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-27 ssh enabled telnet enabled web enabled set mgmt-auth-notify Use this command to either enable or disable the Management Authentication Notification MIB.
Managing the Management Authentication Notification MIB clear mgmt-auth-notify 2-28 Startup a nd General Configuration This example shows how to set only the console .
clear mgmt-auth-notify Managing the Managem ent Authentication Notification MIB Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-29 Matrix(su)->clear mgmt-auth-notify Matrix(su)->show mgm.
Setting Basic Device Properties clear mgmt-auth-notify 2-30 Startup a nd General Configuration Setting Basic Device Properties Purpose To display and set the system IP addr.
show ip address Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-31 show ip address Use this command to display the system IP address and subnet mask. Synt ax show ip address Parameters None.
Setting Basic Device Properties clear ip address 2-32 Startup a nd General Configuration Parameters Default s If not specified, ip ‐ mask will be set to the natural mask of the ip ‐ addr ess and ip ‐ gateway wil l be set to the ip ‐ address .
set ip gratuitous-arp Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-33 Parameters None. Default s None. Mode Switch command, Read ‐ Only .
Setting Basic Device Properties show system 2-34 Startup a nd General Configuration Parameters None. Default s None. Mode Switch command, Read ‐ Wr i t e .
show system hardware Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-35 Temp-Alarm Uptime d,h:m:s Logou t ------------- -------------- ----- -------- off 0,19:4.
Setting Basic Device Properties show system hardware 2-36 Startup a nd General Configuration Example The following example shows a portion of the information display ed with the show system hardware command.
show system utilization Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-37 Lookup DDR: 8 MB 8 MB 8 MB Transmit DDR: 8 MB 8 MB 8 MB Receive DDR: 8 MB 8 MB 8 MB R.
Setting Basic Device Properties show system utilization 2-38 Startup a nd General Configuration Name ProcI D 5 sec 1 min 5 min ------------------------------------ ------------------------ CLI 1 0.0% 0.0% 0.0% Chassis Data Synchronization 2 0.0% 0.0% 0.
set system utilization threshold Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-39 Router OSPF 40 0.0% 0.0% 0.0% Router RIP 41 0.0% 0.0% 0.0% Router VRRP 42 0.0% 0.0% 0.0% Router DVMRP 43 0.0% 0.0% 0.0% Router PIM 44 0.
Setting Basic Device Properties clear system utilization 2-40 Startup a nd General Configuration clear system utilization Use this command to clear the threshold for sending CPU utilization notification messages.
set time Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-41 set time Use this command to change the time of day on the system clock. Synt ax set time [ mm/dd/yyyy ] [ hh:mm:ss ] Parameters Default s None.
Setting Basic Device Properties set summertime 2-42 Startup a nd General Configuration End : SUN NOV 04 02:00:00 2007 Offset: 60 minutes (1 hours 0 minute s) Recurring: yes, starting at 2:00 of the se.
set summertim e recurring Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-43 Default s If an offset is not spe cified, none will be applied. Mode Switch command, Read ‐ Wr i t e .
Setting Basic Device Properties clear summertime 2-44 Startup a nd General Configuration Mode Switch command, Read ‐ Wr i t e . Usage These se ttings will start and stop .
set cli compl etion Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-45 Default s None. Mode Switch command, Read ‐ Wr i t e .
Setting Basic Device Properties show banner 2-46 Startup a nd General Configuration Parameters Default s •I f a delay is not specified , none will be set. •I f not specified, the cursor wi ll not refresh .
set banner Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-47 set banner Use this command to set the banner message for pre and post session login. Synt ax set banner { login message | motd message } Parameters Default s None.
Setting Basic Device Properties clear banner 2-48 Startup a nd General Configuration clear banner Use this command to clear the banner message display ed at pre and post session login to a blank string.
show version Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-49 Bp: 01.00.10 Fw: 05.01.56 2 7G4202-30 GR-A13 Hw: 0 Bp: 01.00.05 Fw: 05.01.56 3 7G4202-30 gr-a5 Hw: 0 Bp: 01.00.10 Fw: 05.01.56 4 7G4202-30 GR-R18 Hw: 0 Bp: 01.
Setting Basic Device Properties set system name 2-50 Startup a nd General Configuration set system name Use this command to configure a name for the system. Synt ax set system name [ string ] Parameters Default s If string is not specif ied, the system name will be cleared.
set system con tact Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-51 set system cont act Use this command to identify a contact person for the system.
Setting Basic Device Properties set length 2-52 Startup a nd General Configuration set length Use this command to set the number of lines the CLI will display . Synt ax set length screenlength Parameters Default s None.
set logout Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-53 set logout Use this command to set the time (in minutes) an idle console or Te l n e t CLI session will remain connected before timing out.
Setting Basic Device Properties set physical alias 2-54 Startup a nd General Configuration Default s If no parameters are specified, all ph ysical alias information will be displayed. Mode Switch command, Read ‐ Only .
clear physical alias Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-55 Mode Switch command, Read ‐ Wr i t e .
Setting Basic Device Properties set physical assetid 2-56 Startup a nd General Configuration Parameters Default s None. Mode Switch command, Read ‐ Only . Example This example shows how to display asset ID information for modul e 1.
clear physical assetid Setting Basic Device Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-57 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
Activating Licensed Features set license 2-58 Startup a nd General Configuration Activating Licensed Features In order to enable adv anced features, such as redundant .
show license Activating Licensed Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-59 Parameters Default s If not specified, the license will be bound to all modules. Mode Switch command, Read ‐ Wr i t e .
Activating Licensed Features clear license 2-60 Startup a nd General Configuration clear license Use this command to clear license key settings.
show inlinepower Configu ring Power over Ethernet (PoE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-61 Configuring Power over Ethernet (PoE) Purpose To review and set PoE .
Configuring Power over Ethernet (PoE) set inlinepower mode 2-62 Startup a nd General Configuration Parameters None. Default s None. Mode Switch command, Read ‐ Only . Example This example shows how to display device PoE properties.
clear inlinepower mode Configu ring Power over Ethernet (P oE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-63 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring Power over Ethernet (PoE) clear inlinepower available 2-64 Startup a nd General Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set inlinepower powertrap Configuring Power over Ethernet (PoE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-65 set inlinepower powertrap Use this command to disable or .
Configuring Power over Ethernet (PoE) set inlinepower assigned 2-66 Startup a nd General Configuration set inlinepower assigned Use this command to manually assign Po we r Sourcing Equipment (PSE) powe r to a modul e in the chassis.
set inlinepower threshold Configuring Power over Ethernet (PoE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-67 Example This example shows how to clear power ass.
Configuring Power over Ethernet (PoE) set inlinepower management 2-68 Startup a nd General Configuration Example This example shows how to reset the Po E threshold .
set inlinepower psetrap Configuring Power over Ethernet (PoE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-69 Example This example shows how to reset the Po E .
Configuring Power over Ethernet (PoE) show port inlinepower 2-70 Startup a nd General Configuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to .
clear port inlinepower Configuring Power over Ethernet (PoE) Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-71 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to enable Po E on port fe.
Reviewing and Selecting a Boot Firmware Image clear port inlinepower 2-72 Startup a nd General Configuration Reviewing and Selecting a Boot Firmware Image Downloading a New Firmware Image Yo u can.
clear port inlinepower Reviewing and Selecting a Boot Firmware Image Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-73 Testing SDRAM.... PASSED. Loading Boot Image: 01.00.02... DONE. Uncompressing Boot Image... DONE. Press any key to enter System Image Loader menu 2.
Reviewing and Selecting a Boot Firmware Image show boot system 2-74 Startup a nd General Configuration 9. Set the terminal baud rate back to 9600 and press ENTER. 10. T ype setboot filename to set the device to boot to the new firmware image.
set boot system Reviewing and Selecting a Boot Firmware Image Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-75 Usage The system must be reset by software for the ne w boot image to take effect at sta rtup.
Starting and Configuring Telnet show telnet 2-76 Startup a nd General Configuration S t arting and Configuring T elnet Purpose To enable or di sable Te l n e t , and to start a Te l n e t session to a remote host.
set telnet Starting and Configuring Telnet Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-77 set telnet Use this command to enable or disable Te l n e t on the device. Synt ax set telnet { enable | disable }{ inboun d | outbound | all } Parameters Default s None.
Starting and Configuring Telnet show router telnet 2-78 Startup a nd General Configuration Example This example shows how to start a Te l n e t session to a host at 10.21.42.13: Matrix(rw)->telnet 10.
clear router telnet Starting and Configuring Telnet Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-79 clear router telnet Use this command to reset Te l n e t service to the router to the default st ate of disabled.
Managing Configuration and Image Files clear router telnet 2-80 Startup a nd General Configuration Managing Configuration and Image Files Matrix Series devices provide a single .
dir Managing Configuration and Image Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-81 dir Use this command to list files stored in the file system.
Managing Configuration and Image Files dir 2-82 Startup a nd General Configuration slot6: Filename: 04.21.03 (Active) (Bo ot) Version: 04.21.03 Size: 5494579 (bytes) Date: FRI JUL 30 08:50:40 2 004 Ch.
show file Managing Configuration and Image Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-83 show file Use this command to display the contents of an image or configuration file. Synt ax show file filename Parameters Default s None.
Managing Configuration and Image Files show file 2-84 Startup a nd General Configuration config t write file exit disable exit end router # arp ! # cdp ! # console ! begin ! # ***** NON-DEFAULT CONFIG.
show config Managing Configuration and Ima ge Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-85 ! # cdp ! # console ! show config Use this command to display the system configuration or write the configuration to a file .
Managing Configuration and Image Files configure 2-86 Startup a nd General Configuration interface loopback 1 ip address 2.2.2.2 255.255.255.255 no shutdown . . . end configure Use this command to execute a previously downloaded configuration file stored on the device.
delete Managing Configuration and Image Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-87 Parameters Default s None. Mode Switch, Read ‐ Wr i t e .
Managing Configuration and Image Files script 2-88 Startup a nd General Configuration Default s None. Mode Switch, Read ‐ Wr i t e . Usage Use the show config command as described in “ show config ” (page 2 ‐ 85)to display current image and configuration file names.
script Managing Configuration and Ima ge Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-89 script file requ ires two argu ments, a por t string (%1) and a VLAN id (%2). Finally , the scri pt is executed, by specifying fe.
Enabling or Disabling the Path MTU Discovery Protocol sh ow mtu 2-90 Startup a nd General Configuration Enabling or Disabling the Path MTU Discovery Protocol Purpose To enable or disable the path MTU (Maximum T ransmission Unit) discovery protocol on the device.
set mtu Enabling or Disabling the Path MTU Discovery Protocol Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-91 set mtu Use this command to disable or re ‐ enable path MTU discov ery protocol on the device.
Pausing, Clearing and Closing the CLI cls (clear screen) 2-92 Startup a nd General Configuration Pausing, Clearing and Closing the CLI Purpose To clear the CLI screen or to close you r CLI session.
exit | quit Pausing, Clearing and Closing the CLI Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-93 Default s None. Mode Switch command, Read ‐ Only . Usage By default, device ti meout occurs after 15 minutes of user inactivity , automatically closing you r CLI session.
Resetting the Device show reset 2-94 Startup a nd General Configuration Resetting the Device Purpose To reset one or mor e device modules, to clear the user ‐.
reset Resetting the Device Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-95 reset Use this command to reset the device without losing any user ‐ defined configuration settings Synt ax reset {[ mod | system | nemcpu { mod .
Resetting the Device reset at 2-96 Startup a nd General Configuration reset at Use this command to schedule a system reset at a specific futu re time. This feature is useful for loading a new boot image.
clear config Resetting the Device Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-97 Parameters Default s If a reason is not specified, none will be applied.
Gathering Technical Support Inform ation show support 2-98 Startup a nd General Configuration Gathering T echnical Support Information Purpose To gather common technical support information. Command show support Use this command to display output for technical support ‐ related commands.
show support Gathering Technical Support Information Enterasys Matrix DFE-Gold Series Configuratio n Guide 2-99 Example This example shows how to execute the show support command and save the results to slot 1 as a support3.
Preparing the Device for Router Mode show support 2-100 Startup and General Configuration Prep aring the Device for Router Mode Pre-Routing Configuration T asks The following pre ‐ routing .
show support Reviewing and Configuring Routing Enterasys Matrix DFE-Gold Series Configur ation Guide 2-101 The example in Figure 2 ‐ 8 shows how to: •E n a b l e routing for this router . • Configure VLAN 1 on IP address 182.
Reviewing and Configuring Routing show router 2-102 Startup and General Configuration show router Use thi s command to display which module that is currently running routing services.
router Reviewing and Configuring Routing Enterasys Matrix DFE-Gold Series Configur ation Guide 2-103 router Use this command to enter router CLI mode. Synt ax router Parameters None. Default s None. Mode Switch command, Read ‐ Wr i t e .
Reviewing and Configuring Routing router 2-104 Startup and General Configuration Router Configuration Mode Set IP prot ocol parameters. Ty p e router and the protoc ol name (and, for OSPF , the instance ID ) from Global or Interface Configuration mode.
router Reviewing and Configuring Routing Enterasys Matrix DFE-Gold Series Configur ation Guide 2-105 DHCP Host Configuration Mode Configure DHCP host parameters. Ty p e clie nt-identifier and the iden tifier , or hardware-addr ess and an address from any DHCP configuration mode.
Reviewing and Configuring Routing router 2-106 Startup and General Configuration.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 3-1 3 Discovery Protocols Configuration This chapter describes how to configure the discov ery protocols supported by the firmw are using CLI commands.
Displaying Neighbors show neighbors 3-2 Discove ry Protocols Configuration Default s If port ‐ string is not specif ied, all Netw ork Neighbor Discov ery information will be display ed. Mode Switch command, Read ‐ Only .
show cdp Enterasys Discov ery Protocol Enterasys Matrix DFE-Gold Series Configuration Gu ide 3-3 Enterasys Discovery Protocol Purpose To enable and configure the Enterasys Discovery Protocol (CDP), used to discover netw ork topology .
Enterasys Discovery Protocol set cdp state 3-4 Discove ry Protocols Configuration CDP Authentication Code : 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 CDP Transmit Frequency : 60 Port Status ----------------- fe.1.1 auto-enable fe.
set cdp auth Enterasys Discov ery Protocol Enterasys Matrix DFE-Gold Series Configuration Gu ide 3-5 Parameters Default s If port ‐ string is not specif ied, the CDP state will be globally set. Mode Switch command, Read ‐ Wr i t e .
Enterasys Discovery Protocol set cdp interval 3-6 Discove ry Protocols Configuration A device with the default authentication code (16 null characters) will .
clear cdp Enterasys Discov ery Protocol Enterasys Matrix DFE-Gold Series Configuration Gu ide 3-7 Example This example shows how to set CDP hold time to 60 .
Cisco Discovery Protocol show ciscodp 3-8 Discove ry Protocols Configuration Cisco Discovery Protocol Purpose To enable and configure the Cisco Discovery Protocol, use d to discover network topology .
show ciscodp port info Cisco Discovery Protocol Enterasys Matrix DFE-Gold Series Configuration Gu ide 3-9 Device ID : 00E06314BD57 Last Change : WED FEB 08 01:07:45 20 06 Ta b l e 3 ‐ 2 provides an explanation of the command output.
Cisco Discovery Protocol set ciscodp status 3-10 Discovery Protocols Con figuration fe.1.1 enabled none untrus ted 0 fe.1.2 enabled none untrus ted 0 fe.1.3 enabled none untrus ted 0 fe.1.4 enabled none untrus ted 0 fe.1.5 enabled none untrus ted 1 Ta b l e 3 ‐ 3 provides an explanation of the command output.
set ciscodp timer Cisco Discovery Protocol Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-11 set ciscod p timer Use this command to set the number of seconds between Cisco Di scovery Pr otocol PDU transmissions.
Cisco Discovery Protocol set ciscodp port 3-12 Discovery Protocols Con figuration set ciscod p port Use this command to set the status, vo i ce VLAN, extended t.
clear ciscodp Cisco Discovery Protocol Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-13 •A Cisco DP port trust status of trusted or untrusted is .
Cisco Discovery Protocol clear ciscodp 3-14 Discovery Protocols Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e . Examples This example shows how to c.
clear ciscodp Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-15 Link Layer Discovery Protocol and LLDP-MED The IEEE 802.
Link Layer Discovery Protocol and LLDP-MED clear ciscodp 3-16 Discovery Protocols Con figuration Commands Ste p Ta s k Command(s) 1. Configure global system LLDP p arameters set lldp tx-interval set lldp hold-multiplier set lldp trap-interval set lldp med-fast-repeat clear lldp 2.
show lldp Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-17 show lld p Use this command to display LLDP configuration information. Synt ax show lldp Parameters None. Default s None.
Link Layer Discovery Protocol and LLDP-MED show lldp port status 3-18 Discovery Protocols Con figuration show lld p port st atus Use this command to display the LLDP status of one or more ports.
show lldp port tx-tlv Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-19 Mode Switch command, Read ‐ Only .
Link Layer Discovery Protocol and LLDP-MED show lldp port location-info 3-20 Discovery Protocols Con figuration Desc Name Desc Cap Addr Id Id PHY Aggr Frame Cap Pol Loc PoE ------- ---- ---- ---- --- ---- --- - ---- --- --- ---- ---- --- --- --- --- ge.
show lldp port local-info Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-21 Parameters Default s If port ‐ string is not specif ied, local system information will be displayed for all po rts.
Link Layer Discovery Protocol and LLDP-MED show lldp port lo cal-info 3-22 Discovery Protocols Con figuration Sys Name Optional basic LLD P TL V . V alue is the administrative ly assigned name for the system. Sys Desc Optional basic LLDP TL V . V a lue is sysDescr object defined in RFC 3418.
show lldp port remote-info Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-23 show lld p port remote-info Use this command to display the remote sy stem information stored for a remote device connected to a local port.
Link Layer Discovery Protocol and LLDP-MED show lldp port network-policy 3-24 Discovery Protocols Con figuration Mgmt Addr : 0.0.0.0 Chassis ID : 0.0.0.
show lldp port network-policy Link Lay er Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-25 Parameters Default s If port ‐ string is not spec.
Link Layer Discovery Protocol and LLDP-MED set lldp tx-interva l 3-26 Discovery Protocols Con figuration set lld p tx-interval Use this command to set the time, in seco.
set lldp trap-interval Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-27 Example This example sets the transmit inte rval to.
Link Layer Discovery Protocol and LLDP-MED set lldp port status 3-28 Discovery Protocols Con figuration Mode Switch command, Read ‐ Wr i t e .
set lldp port trap Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-29 set lld p port trap Use this command to enable or disable sending LLDP notifications (traps) when a remote system change is dete cted.
Link Layer Discovery Protocol and LLDP-MED set lldp port location-info 3-30 Discovery Protocols Con figuration Example This example enables transmitting LLDP ‐ MED traps on ports ge.1.1 through ge.1.6 . Matrix(rw)->set lldp port med-trap e nable ge.
set lldp port tx-tlv Link Layer Discovery Prot ocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-31 Parameters all Add all optional TL Vs to transmitted LLDPDUs. port ‐ desc Po r t Description optional basic LLDP TL V .
Link Layer Discovery Protocol and LLDP-MED set lldp port network-policy 3-32 Discovery Protocols Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e .
set lldp port network-policy Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-33 Default s None. Mode Switch command, Read ‐ Wr i t e .
Link Layer Discovery Protocol and LLDP-MED clear lldp 3-34 Discovery Protocols Con figuration clear lld p Use this command to return LLDP parameters to their defaul t va l ue s . Synt ax clear lldp { all | tx-interval | hold-multipler | trap-interval | med-f ast-repeat } Parameters Default s None.
clear lldp port trap Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-35 Example This example returns port ge.1.1 to the default state of enabled for both transmitting and processing received LLDPDUs.
Link Layer Discovery Protocol and LLDP-MED clear lldp por t location-info 3-36 Discovery Protocols Con figuration clear lld p port location-info Use this command to return the port ECS ELIN location setting to the def ault va l u e of null.
clear lldp port tx-tlv Link Layer Discovery Protocol and LLDP-MED Enterasys Matrix DFE-Gold Series Configuratio n Guide 3-37 Default s At least one application (or all ) and one policy parameter must be speci fied.
Link Layer Discovery Protocol and LLDP-MED clear lldp port tx-tlv 3-38 Discovery Protocols Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e .
Enterasys Matrix DFE-Gold Series Configuration Gu ide 4-1 4 Port Configuration This chapter descri bes the Po r t Configuration set of commands and how to use them.
Port Configuration Summary 4-2 Port Conf iguration Switch Port s The Matrix Ser ies modules and standalone devices have fixed front panel switch ports and, depending on the model, optional expansion module slots.
Setting Console Port Properties Enterasys Matrix DFE-Gold Series Configuration Gu ide 4-3 fe.1.1-10 This example shows the port ‐ string syntax for specifying the 1 ‐ Gigabit Ethernet port 14 in the module in chassis sl ot 3.
Setting Console Port Properties show console 4-4 Port Conf iguration show console Use this command to display properties set for one or more console ports.
show console baud Setting Console Port Properties Enterasys Matrix DFE-Gold Series Configuration Gu ide 4-5 Parameters Default s If port ‐ string is not specif ied, properties for all console ports will be cleared.
Setting Console Port Properties clear console baud 4-6 Port Conf iguration Parameters Default s If port ‐ string is not specif ied, baud rate will be set for all console ports. Mode Switch command, Read ‐ Wr i t e .
set console flowcontrol Setting Console Port Properties Enterasys Matrix DFE-Gold Series Configuration Gu ide 4-7 Default s If port ‐ string is not specif ied, the flow con trol setting for all console port s will be displa yed.
Setting Console Port Properties show console bits 4-8 Port Conf iguration Parameters Default s If port ‐ string is not specif ied, flow control will be clea red for all console ports. Mode Switch command, Read ‐ Wr i t e .
clear console bits Setting Console Port Properties Enterasys Matrix DFE-Gold Series Configuration Gu ide 4-9 Parameters Default s If port ‐ string is not specif ied, bits per character will be set for all console ports.
Setting Console Port Properties set console stopbits 4-10 Port Con figuration Default s If port ‐ string is not specif ied, stop bits per character will be displayed for all console ports. Mode Switch command, Read ‐ Wr i t e .
show console parity Setting Console Por t Properties Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-11 Default s If port ‐ string is not specif ied, stop bits per character will be cleared for all console ports.
Setting Console Port Properties clear console parity 4-12 Port Con figuration Default s If port ‐ string is not specif ied, parit y type will be set for all console ports. Mode Switch command, Read ‐ Wr i t e .
show port Reviewing Port Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-13 Reviewing Port St atus Purpose To display operating status, duplex mode, speed, p.
Reviewing Port Status show port status 4-14 Port Con figuration show port st atus Use this command to display operating and admin status, speed, duplex mode and port type for one or more ports on the device.
show port counters Reviewing Port Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-15 show port counters Use this command to display port counter statistics detailing traffic through the device and through all MIB2 network devi ces.
Reviewing Port Status show port counters 4-16 Port Con figuration No counter discontinuity time ------------------------------------ ----------------------------- MIB2 Interface Counters -------------.
show port operstatuscause Reviewing Port Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-17 show port operst a tuscause Use this command to display the causes configured to place operating status to a down or dormant state for one or more ports.
Reviewing Port Status clear port operstatuscause 4-18 Port Con figuration Mode Switch command, Read ‐ Only . Example This example shows how to display operation status causes for ports ge.1.1 through 6.
clear port operstatuscause Reviewing Port Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-19 Mode Switch command, Read ‐ Wr i t e .
Disabling / Enabling and Naming Ports set port disable 4-20 Port Con figuration Disabling / Enabling and Naming Port s Purpose To disable and re ‐ enable one or more ports, and to as sign an alias to a port.
set port enable Disabling / Enabling and Naming Ports Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-21 set port enable Use this command to administratively enable one or more ports. Synt ax set port enable port-string Parameters Default s None.
Disabling / Enabling and Naming Ports set port alias 4-22 Port Con figuration set port alias Use this command to assign an alias name to a port.
set forcelinkdown Disabling / Enabling and Naming Ports Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-23 set forcelinkdown Use this command to enable or disable the force link down function.
Setting Speed and Duplex Mode show port speed 4-24 Port Con figuration Setting S peed and Duplex Mode Purpose To review and set the operational speed in Mbps and .
set port speed Setting Speed and Duplex Mode Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-25 set port speed Use this command to set the default speed of one or more ports.
Setting Speed and Duplex Mode set port duplex 4-26 Port Con figuration Example This example shows how to display the default duplex setting for 1 ‐ Gigabit Ethe rnet port 14 in module 3: Matrix(rw)->show port duplex ge.
show port jumbo Enabling / Disabling Jumbo Frame Support Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-27 Enabling / Disabling Jumbo Frame Support Purpose To review , enable, and disable jumbo frame support on one or more ports.
Enabling / Disabling Jumbo Frame Support set port jumbo 4-28 Port Con figuration set port jumbo Use this command to enable or disable jumbo frame support on one or more ports.
clear port jumbo Enabling / Disabling Jumbo Frame Support Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-29 Mode Switch command, Read ‐ Wr i t e .
Setting Auto-Negotiation and Advertised Ability show port negotiation 4-30 Port Con figuration Setting Auto-Negotiation and Advertised Ability Purpose To review , disable or enable auto ‐ negotiation, and to review or set a port’ s advertised mode of operation.
set port negotiation Setting Auto-Negotiation and Advertised Ability Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-31 Mode Switch command, Read ‐ Only .
Setting Auto-Negotiation and Advertised Ability set port mdix 4-32 Port Con figuration Default s If port ‐ string is not specif ied, the mode for al l ports will be displayed. Mode Switch command, Read ‐ Only .
clear port mdix Setting Auto- Negotiation and Advertised Ability Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-33 clear port mdix Use this command to reset MDIX mode to the default setting of auto on one or more ports.
Setting Auto-Negotiation and Advertised Ability set port advertise 4-34 Port Con figuration 10BASE-T yes yes no 10BASE-TFD yes yes no 100BASE-TX yes yes no 100BASE-TXFD yes yes no 1000BASE-X no no no .
clear port advertise Setting Auto-Negotiation and Advertised Ability Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-35 Parameters Default s At least one optional parameter must be specified. Mode Switch command, Read ‐ Wr i t e .
Setting Auto-Negotiation and Advertised Ability clear port advertise 4-36 Port Con figuration Default s If not specified, all modes of advertised ability will be cleared. Mode Switch command, Read ‐ Wr i t e .
show port flowcontrol Setting Flow Contro l Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-37 Setting Flow Control Purpose To review , enable or disable por t flow control.
Setting Flow Control set port flowcontrol 4-38 Port Con figuration Ta b l e 4 ‐ 4 provides an explanation of the command output. set port flowcontrol Use this command to enable or disable flow control settings for one or more ports.
show port trap Configuring Link Traps and Link Flap Detection Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-39 Configuring Link T rap s and Link Flap Detection Purpose To disable or re ‐ enable link traps and to configure the link flapping detection function.
Configuring Link Traps and Link Flap D etection set port trap 4-40 Port Con figuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to display link trap status for fe.3.1 through 4: Matrix(rw)->show port trap fe.
show linkflap Configuring Link Traps and Link Flap Detection Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-41 Parameters Default s •I f not specified, information about all link flap detection settings will be display ed.
Configuring Link Traps and Link Flap D etection show linkflap 4-42 Port Con figuration Linkflap Port Settable Parameter Tab le (X means error occurred) Port LF Status Actions Thresh old Interval Downtime -------- --------- ------- ------ ---- ---------- ---------- ge.
set linkflap globalstate Configuring Link Traps and Link Flap Detection Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-43 set linkflap globalst ate Use this command to globally enable or disable the link flap detection function.
Configuring Link Traps and Link Flap D etection set linkflap interval 4-44 Port Con figuration set linkflap interval Use this command to set the time interval (in seconds) for accumulating link down transitions.
clear linkflap action Configuring Link Traps and Link Flap Detection Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-45 Mode Switch command, Read ‐ Wr i t e . Examples This example shows how to set the link flap violation action on port fe.
Configuring Link Traps and Link Flap D etection set linkflap downtime 4-46 Port Con figuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Examples This example shows how to set the link flap threshold on port fe.
clear linkflap down Configuring Link Traps and Link Flap Detection Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-47 clear linkflap down Use this command to toggle link fl ap disabled ports to operational.
Configuring Link Traps and Link Flap D etection clear link flap 4-48 Port Con figuration Examples This example shows how to clear all link flap options on port fe.1 .4: Matrix(rw)->clear linkflap all fe.
show port broadcast Configuring Broadcast Supp ression Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-49 Configuring Broadcast Suppression Purpose To review , disable or set the broadcas t thresholds on one or mo re ports.
Configuring Broadcast Suppression set port broadcast 4-50 Port Con figuration set port broadcast Use this command to set the broadcast suppression limit, in pac kets per second, on one or more ports.
clear port broadcast Configuring Broadcast Suppression Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-51 Parameters Default s If not specified, both threshold and peak settings will be cleared. Mode Read ‐ Wr i t e .
Configuring Port Mirroring show port mirroring 4-52 Port Con figuration Configuring Port Mirroring The Matrix device allows you to mirror (or redirec t) the tra.
set port mirroring Configuring Port Mirroring Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-53 Parameters None. Default s None. Mode Switch command, Read ‐ Only . Example This example shows how to display port mirroring information.
Configuring Port Mirroring clear port mirroring 4-54 Port Con figuration Default s If not specified, both receiv ed and transmitted frames will be mirrore d.
clear port mirroring Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-55 Configuring LACP Using multiple links simultaneously to increase bandwidth .
Configuring LACP clear port mirroring 4-56 Port Con figuration •A means of identifying the set of capabi lities associated with each port and with each aggregator , as understood by a given device.
clear port mirroring Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-57 by comparing operational keys. Aggregator ports allow only underlying ports with keys matching theirs to join their LAG.
Configuring LACP show lacp 4-58 Port Con figuration show lacp Use this command to display the global LACP enable state, or to display information about one or more aggregator ports.
set lacp Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-59 Actor Partner System Identifier: 00:e0:63:9d:b5:8 7 00:00:00:00:00:00 System Priority: 3276 8 32768 Admin Key: 3276 8 Oper Key: 3276 8 32768 Attached Ports: None. Ta b l e 4 ‐ 9 provides an explanation of the command output.
Configuring LACP clear lacp state 4-60 Port Con figuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to disable LACP: Matrix(rw)->set lacp disable clear lacp st ate Use this command to reset LACP to the defa ult state of enabled.
set lacp aadminkey Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-61 Usage Only one LACP system priority can be set on a Matrix Se.
Configuring LACP set lacp static 4-62 Port Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear the actor admin key for LAG port 4: Matrix(rw)->clear lacp aadminkey lag .
clear lacp static Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-63 Example This example shows how to add port fe. 1.6 to the LAG of aggregator port 4: Matrix(rw)->set lacp static lag.
Configuring LACP set singleportlag 4-64 Port Con figuration Example This example shows how to display the status of the single port LAG function: Ma.
show port lacp Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-65 show port lacp Use this command to display link aggregation informatio n for one or more underlying physical ports.
Configuring LACP set port lacp 4-66 Port Con figuration Matrix(rw)->show port lacp port fe.1 .12 status summary Port AggrActor System Partner System Pri: Sys tem ID: Key: Pri: System ID : Key: fe.
set port lacp Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-67 Default s •A t least one parameter must be entered per port ‐ string.
Configuring LACP clear port lacp 4-68 Port Con figuration partners maintain current status of the other via LACPDUs containing information about their ports’ LACP status and operational state.
show lacp flowRegeneration Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-69 Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear all link aggregation parameters for port ge.
Configuring LACP clear lacp flowRegeneration 4-70 Port Con figuration Usage When enabled and a new port joins a link aggregation group (LAG), LACP will redistri bute all existing flows over the LAG.
set lacp outportAlgorithm Configuring LACP Enterasys Matrix DFE-Gold Series Configuratio n Guide 4-71 Example This example shows how to display the current LACP: Matrix.
Configuring LACP clear lacp outportAlgorithm 4-72 Port Con figuration Example This example shows how to reset the LACP outport algorithm to DIP ‐ SIP: Mat.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 5-1 5 SNMP Configuration This chapter descri bes the Simple Network Management Protocol (SNMP) set of commands and how to use them.
SNMP Configuration Summary 5-2 SNMP Configuration SNMPv1 and SNMPv2c The components of SNMPv1 and SNMPv2c network management fall into thr ee categories: .
SNMP Configuration Summary Enterasys Matrix DFE-Gold Series Configuration Gu ide 5-3 Using SNMP Context s to Access S pecific MIBs By default, when operating from the switch CLI, Matrix Series devices allow access to all SNMP MIBs or contexts.
SNMP Configuration Summary 5-4 SNMP Configuration Complete an SNMPv2 trap configuration on a Matrix Series device as follows: 1. Create a commun ity name that will act as an SNMP user password.
show snmp engineid Reviewing SNMP Statistics Enterasys Matrix DFE-Gold Series Configuration Gu ide 5-5 How SNMP Will Use This Configuration In order to send a trap/notification .
Reviewing SNMP Statistics show snmp counters 5-6 SNMP Configuration Default s None. Mode Switch command, Read ‐ Only . Example This example shows how to display SNMP .
show snmp counters Reviewing SNMP Statistics Enterasys Matrix DFE-Gold Series Configuration Gu ide 5-7 snmpOutPkts = 396601 snmpInBadVersions = 0 snmpInBadCommunityNames = 0 snmpInBadCommunityUses = 0.
Reviewing SNMP Statistics show snmp counters 5-8 SNMP Configuration snmpInGe nErrs Number of SNMP PDUs delivered to the SNMP protocol entit y with the value of t he error-stat us field as “gen Err .
show snmp counters Reviewing SNMP Statistics Enterasys Matrix DFE-Gold Series Configuration Gu ide 5-9 usmS tats NotInTimeWindows Number of packets received by the SN MP engine that were dropped because they appeared outside of the authori tative SNMP engine's window .
Configuring SNMP Users, Groups and Communities show snmp user 5-10 SNMP Configurat ion Configuring SNMP Users, Group s and Communities Purpose To review and configure SNMP users, groups and v1 and v2 communities.
show snmp user Configuring SNMP Users, Groups and Communities Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-11 •I f user is not specified, information about all SNMP users will be displayed.
Configuring SNMP Users, Groups and Communities set snmp user 5-12 SNMP Configurat ion set snmp user Use this command to create a new SNMPv3 user .
show snmp group Configuring SNMP Users, Groups and Communities Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-13 Default s If remote is not specified , the user will be remov ed from the local SNMP eng ine.
Configuring SNMP Users, Groups and Communities set snmp group 5-14 SNMP Configurat ion Storage type = nonVolatil e Row status = active Security model = SNMPv1 Security/user name = public.
clear snmp group Configuring SNMP Users, Groups and Communities Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-15 Example This example shows how to create an SNMP .
Configuring SNMP Users, Groups and Communities set snmp community 5-16 SNMP Configurat ion Example This example shows how to displ ay information about the SNMP “public” community name.
clear snmp community Configuring SN MP Users, Groups and Communities Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-17 Examples This example shows how to set an SN.
Configuring SNMP Access Rights show snmp access 5-18 SNMP Configurat ion Configuring SNMP Access Right s Purpose To review and configure SNMP access rights and assign viewing privileges and security levels to SNMP user groups.
show snmp access Configuring SNMP Access Rights Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-19 •I f volatile , nonvolatile or read ‐ only are not specif ied, all entries of all storage types wil l be display ed.
Configuring SNMP Access Rights set snmp access 5-20 SNMP Configurat ion set snmp access Use this command to set an SNMP access configuration.
clear snmp access Configuring SNMP Access Rights Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-21 •I f write view is not specified, none will be applied. •I f notify view is not specified, none will be applied.
Configuring SNMP MIB Views show snmp view 5-22 SNMP Configurat ion Configuring SNMP MIB V iews Purpose To review and configure SNMP MIB views.
show snmp cont ext Configuring SNMP MIB Views Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-23 View Type = included Storage type = nonVolatile Row status = active View Name = All Subtree OID = 0.0 Subtree mask = View Type = included Storage type = nonVolatile Row status = active View Name = Network Subtree OID = 1.
Configuring SNMP MIB Views set snmp view 5-24 SNMP Configurat ion Mode Switch command, Read ‐ Only . Usage An SNMP context is a collection of management information that can be accessed by an SNMP agent or entity .
clear snmp view Configuring SNMP MIB Views Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-25 Example This example shows how to set an SNMP MI B view to “public” with a subtree name of 1.
Configuring SNMP Target Parameters show snmp targetparams 5-26 SNMP Configurat ion Configuring SNMP T arget Parameters Purpose To review and configure SNMP target parameters. This controls where and under what circumstances SNMP notifications will be se nt.
set snmp targetparams Configuring SNMP Target Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-27 Storage type = nonVolatil e Row status = active Target Parameter Name = v2cExample Params Security Name = public Message Proc.
Configuring SNMP Target Parameters clear snmp tar getparams 5-28 SNMP Configurat ion Default s None. •I f not specified, security lev el will be set to noa uthenticatio n. •I f not specified, storage type will be set to nonvolatile .
show snmp targetaddr Configuring SNMP Target Addresses Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-29 Configuring SNMP T arget Addresses Purpose To review and configure SNMP target addresses which will receive SNMP notifica tion messages.
Configuring SNMP Target Addresses set snmp targetaddr 5-30 SNMP Configurat ion Retry count = 4 Parameters = v2cParams Storage type = nonVolatil e Row status = active Ta b l e 5 ‐ 10 shows a detailed explanation of the command output.
clear snmp targetaddr Configuring SNMP Target Addresses Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-31 Default s •I f not specified, udpport will be set to 162 . •I f not specified, mask wi ll be set to 255.
Configuring SNMP Target Addresses clear snmp targetaddr 5-32 SNMP Configurat ion Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear SNMP .
show snmp notify Configuring SNMP Notification Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-33 Configuring SNMP Notification Parameters Purpose To configure SNMP notification parameters and optional filters.
Configuring SNMP Notification Parameters show snmp notify 5-34 SNMP Configurat ion Parameters Default s •I f a notify name is not specified, all entries will be displayed.
set snmp notify Configuring SNMP Notification Par ameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-35 set snmp notify Use this command to set the SNMP notify configuration.
Configuring SNMP Notification Parameters show snmp notifyfilter 5-36 SNMP Configurat ion Default s None. Mode Switch command, Read ‐ Wr i t e .
set snmp notifyfilter Configuring SNMP Notifica tion Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-37 set snmp notifyfilter Use this command to create an SN MP notify filter configuration.
Configuring SNMP Notification Parameters show snmp notifyprofile 5-38 SNMP Configurat ion Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to delete the SNMP notify filter “pilot1”: Matrix(rw)->clear snmp notifyfilter pilot1 subtree 1.
set snmp notifyprofile Configuring SNMP Notification Para meters Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-39 set snmp notifyprofile Use this command to create an SN MP notify filter profile configuration.
Configuring SNMP Notification Parameters clear snmp notifyprofile 5-40 SNMP Configurat ion Example This example shows how to delete SNMP notify profile “area51”.
set snmp timefilter break Configuring SNMP Walk Behavior Enterasys Matrix DFE-Gold Series Configuratio n Guide 5-41 Configuring SNMP W alk Behavior Purpose To configure SNMP wa l k behavior .
Configuring SNMP Walk Behavior set snmp timefilter break 5-42 SNMP Configurat ion.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 6-1 6 Spanning T ree Configuration This chapter descri bes the Spanning Tr e e Configuratio n set of command s and how to use them. Overview: Single, Rapid and Multiple S p anning T ree Protocols The IEEE 802.
Overview: Single, Rapid and Mult iple Spanning T ree Protocols 6-2 Spannin g Tree Configuration For details on creating Spanning Tr e e instances, refe r to “ set spantree msti ” on page 6 ‐ 14.
Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuration Gu ide 6-3 •D i s a b l i n g a port based on frequency of failure events P.
Configuring Spanning Tree Bridge Parameters 6-4 Spannin g Tree Configuration clear spantree version 6-10 show spantree stpmode 6-10 set spantree stpmode 6-1 1 clear spantree stpmode 6-1 1 show spantre.
Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuration Gu ide 6-5 set spantree autoedge 6-29 clear spantree autoedge 6-29 show spantree legacypathcost 6-30 set span.
Configuring Spanning Tree Bridge Parameters show spantree stats 6-6 Spannin g Tree Configuration show sp antree st at s Use this command to display Spanning Tr e e information for one or more ports.
show spantree stats Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuration Gu ide 6-7 Bridge Max Age - 20 se c Bridge Hello Time - 2 se c Bridge Forward Delay - 15 .
Configuring Spanning Tree Bridge Parameters show spantree stats 6-8 Spannin g Tree Configuration This example shows how to display port ‐ specif ic Spanning Tr e e information for port ge.1.1. Ta b l e 6 ‐ 2 describes the port ‐ specific information displayed .
show spantree version Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuration Gu ide 6-9 show sp antree version Use this command to display the current version of the Spanning Tree protocol running on the device.
Configuring Spanning Tree Bridge Parameters clea r spantree version 6-10 Spanning Tr ee Configuration mode will cause the bridge to transmit only 802.1D BPDUs, and will prevent non ‐ edge ports fr om rapidly transitioning to forw arding state.
set spantree stpmode Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-11 Example This example shows how to display the ST.
Configuring Spanning Tree Bridge Paramete rs show spantree maxconfigurablestps 6-12 Spanning Tr ee Configuration Example This example shows how to reset the STP mode to IEEE 802.
clear spantree maxconfigurablestps Conf iguring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-13 Example This example shows how to set .
Configuring Spanning Tree Bridge Parameters set spantree msti 6-14 Spanning Tr ee Configuration set sp antree msti Use this command to create or delete a Mult iple Spanning Tr e e instance. Synt ax set spantree msti sid sid { create | delete } Parameters Default s None.
show spantree mstmap Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-15 show sp antree mstmap Use this command to display the mapping of a filteri ng database ID (FID) to a Spanning Tr e e s .
Configuring Spanning Tree Bridge Parameters clear spantree mstmap 6-16 Spanning Tr ee Configuration Example This example shows how to map FID 3 to SID 2: Matrix(rw)->set spantree mstmap 3 si d 2 clear sp antree mstmap Use this command to map a FID back to SID 0.
show spantree mstcfgid Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-17 Example This example shows how to display assignme.
Configuring Spanning Tree Bridge Parameters clear spantr ee mstcfgid 6-18 Spanning Tr ee Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set spantree bridgeprioritymod e Conf iguring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-19 Default s None.
Configuring Spanning Tree Bridge Parameters show spantree priority 6-20 Spanning Tr ee Configuration Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to reset the bridge priority mode to 802.
set spantree priority Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-21 Parameters Default s If sid is not specifie d, priority will be set on Spanning Tr e e 0.
Configuring Spanning Tree Bridge Parameters clear spantree priority 6-22 Spanning Tr ee Configuration clear sp antree priority Use this command to reset the Spanning Tr e e priority to the default va l u e of 32768.
set spantree bridgehellomode Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-23 Example This example shows how to display the Spanning Tr e e bridge hello mode.
Configuring Spanning Tree Bridge Parameters show spantree hello 6-24 Spanning Tr ee Configuration Example This example shows how to reset the Spanning Tr e e bridge.
clear spantree hello Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-25 Example This example shows how to globally set t.
Configuring Spanning Tree Bridge Parameters set spantree maxage 6-26 Spanning Tr ee Configuration set sp antree maxage Use this command to set the bridge maxim um aging time. Synt ax set spantree maxage agingtime Parameters Default s None Mode Switch command, Read ‐ Wr i t e .
show spantree fwddelay Configuri ng Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-27 Example This example shows how to globally reset .
Configuring Spanning Tree Bridge Parameters clear spantree fwddelay 6-28 Spanning Tr ee Configuration addition, each port needs ti me to listen for conflicting info.
set spantree autoedge Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-29 Example This example shows how to display the status of the automatic edge port detection function: Matrix(rw)->show spantree autoedge autoEdge is currently enabled.
Configuring Spanning Tree Bridge Parame ters show spantree legacypathcost 6-30 Spanning Tr ee Configuration show sp antree legacyp athcost Use this command to display the default Spanning Tr e e path cost setting.
clear spantree legacypathcost Confi guring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-31 clear sp antree legacyp athcost Use this command to set the Spanning Tr e e default va l u e for legacy path cost to 802.
Configuring Spanning Tree Bridge Para meters set spantree tctrapsuppress 6-32 Spanning Tr ee Configuration set sp antree tctrap suppress Use this command to disable or enable topology change trap suppression on Rapid Spanning Tree edge por ts.
show spantree txholdcount Configur ing Spanning T ree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-33 Example This example shows how to clear topol.
Configuring Spanning Tree Bridge Pa rameters clear spantree txholdcount 6-34 Spanning Tr ee Configuration Example This example shows how to globally set the transmit .
set spantree maxhops Configuring Spanning T ree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-35 set sp antree maxhop s Use this command to set the Spanning Tr e e maximum hop count. Synt ax set spantree maxhops max_hop_count Parameters Default s None.
Configuring Spanning Tree Bridge Parameters show spantree spanguard 6-36 Spanning Tr ee Configuration show sp antree sp anguard Use this command to display the status of the Spanning Tr e e span guard function.
clear spantree spanguard Configuri ng Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-37 Example This example shows how to enable the .
Configuring Spanning Tree Bridge Parameters set spantree spanguardtimeout 6-38 Spanning Tr ee Configuration set sp antree sp anguard timeout Use this command to set the amount of time (in seconds) an edge port will remain locked by the span guard function.
show spantree spanguardlock Configur ing Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-39 show sp antree sp anguardlock Use this command to display the span guard lock status of one or more ports.
Configuring Spanning Tree Bridge Parameters show spantree spanguardtrapenable 6-40 Spanning Tr ee Configuration Example This example shows how to unlock port fe.
clear spantree spanguardtrap enable Confi guring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-41 clear sp antree sp anguard trap enable Use this comm.
Configuring Spanning Tree Bridge Parameters set spantree backuproot 6-42 Spanning Tr ee Configuration set sp antree backuproot Use this command to enable or disable the Spanning Tr e e backup root function.
show spantree backuproottrapen dable Confi guring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-43 Example This example shows how to reset.
Configuring Spanning Tree Bridge Parameters clear spantree backuproottrapenable 6-44 Spanning Tr ee Configuration Example This example shows how to enable the backup ro.
set spantree newroottrapenable Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-45 set sp antree newroottrapenable Use this command to enable or disable the Spanning Tr e e new root trap function.
Configuring Spanning Tree Bridge Parameters clear spantree default 6-46 Spanning Tr ee Configuration clear sp antree default Use this command to restore default val u e s to a Spanning T ree.
show spantree debug Configuring Spanning Tree Bridge Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-47 Example This example shows how to display Spanning Tr e e debug counter s for link aggregation port 3, SID 0: Matrix(rw)->show spantree debug port lag.
Configuring Spanning Tree Bridge Parameters cle ar spantree debug 6-48 Spanning Tr ee Configuration clear sp antree debug Use this command to clear Spanning Tr e e debug counters. Synt ax clear spantree debug Parameters None.
clear spantree debug Configu ring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-49 Configuring S p anning T ree Port Parameters Purpose To display and .
Configuring Spanning Tree Port Parameters show spantree portenable 6-50 Spanning Tr ee Configuration show sp antree portenable Use this command to display the port status on one or more Spanning Tr e e ports.
clear spantree portenable Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-51 clear sp antree portenable Use this command to reset the default val u e for one or more Spanning Tr e e ports to enabled.
Configuring Spanning Tree Port Parameters set spantree portadmin 6-52 Spanning Tr ee Configuration set sp antree port admin Use this command to disable or enable the Spanning Tr e e algorit hm on one or more ports.
set spantree protomigration Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-53 set sp antree protomigration Use this command to reset the protocol state migration machine for one or more Spanning Tr e e ports.
Configuring Spanning Tree Port Para meters show spantree blockedports 6-54 Spanning Tr ee Configuration Example This example shows how to display the Spanning Tr e e state for fe.1.7: Matrix(rw)->show spantree portstate port fe.
set spantree portpri Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-55 Parameters Default s •I f port ‐ string is not specif ied, port priority will be display ed for all Spanning Tr e e ports.
Configuring Spanning Tree Port Parameters clear spantree p ortpri 6-56 Spanning Tr ee Configuration clear sp antree portpri Use this command to reset the bridge priority of a Spanning Tr e e port to a def ault va l u e of 128.
clear spantree porthello Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-57 Usage This command can be executed only if bridge hello mode is disable d.
Configuring Spanning Tree Port Parameters show spantree a dminpathcost 6-58 Spanning Tr ee Configuration •I f sid is not specif ied, port cost will be display ed for all Spanning T rees. Mode Switch command, Read ‐ Only .
clear spantree adminpathcost Configur ing Spanning Tree Port Par ameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-59 Parameters Default s If sid is not specifie d, admin path cost will be set for Spanning Tr e e 0.
Configuring Spanning Tree Port Pa rameters show spantree adminedge 6-60 Spanning Tr ee Configuration Example This example shows how to reset the admin path cost to 0 for fe.3.2 on SID 1: Matrix(rw)->clear spantree adminpath cost fe.
clear spantree adminedge Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-61 Mode Switch command, Read ‐ Wr i t e . Example This example shows how to set fe.1.11 as an edge port: Matrix(rw)->set spantree adminedge f e.
Configuring Spanning Tree Port Parameters show spantree adm inpoint 6-62 Spanning Tr ee Configuration Mode Switch command, Read ‐ Only . Example This example shows how to display the edge port status for fe.
set spantree adminpoint Configuring Spanning Tree Port Parameters Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-63 Default s If not specified, status will be disp layed for all ports. Mode Switch command, Read ‐ Only .
Configuring Spanning Tree Port Parameters clear spantree adminpoint 6-64 Spanning Tr ee Configuration clear sp antree adminpoint Use this command to reset the administrative .
set spantree lp Configuring Spanning Tree Loop Protect Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-65 Configuring S p anning T ree Loop Protect Features Purpose To display .
Configuring Spanning Tree Loop Protect Features show spantree lp 6-66 Spanning Tr ee Configuration Parameters Default s If no SID is specified, SID 0 is assumed. Mode Switch command, Read ‐ Wr i t e . Usage The Loop Protect feature is disabled by default.
clear spantree lp Configuring Spa nning Tree Loop Protect Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-67 If no SID is specified, SID 0 is assumed.
Configuring Spanning Tree Loop Protect Features clear spantree lplock 6-68 Spanning Tr ee Configuration Parameters Default s If no port ‐ string is specified, status is displayed for all ports. If no SID is specified, SID 0 is assumed.
set spantree lpcapablepartner Configuri ng Spanning Tree Loop Protect F eatures Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-69 Usage The default state is unlocked. Example This example shows how to clear Loop Protect lock from ge.
Configuring Spanning Tree Loop Protect Features show spantree lpcapablepartner 6-70 Spanning Tr ee Configuration show sp antree lpcap ablep artner Use this command to the Loop Protect capability of a link partner for one or more ports.
set spantree lpthreshold Configuring Spa nning Tree Loop Protect Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-71 set sp antree lpthreshold Use this command to set the Loop Protect event threshold.
Configuring Spanning Tree Loop Protect Features clear spantree lpthreshold 6-72 Spanning Tr ee Configuration Example This example shows how to display the current Loop .
show spantree lpwindow Configuring Spanning Tree Loop Prote ct Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-73 counter is not reset until the Loop Protect ev ent threshold is reached.
Configuring Spanning Tree Loop Protect Features set spantr ee lptrapenable 6-74 Spanning Tr ee Configuration Example This example shows how to reset the Loop Protect .
clear spantree lptrapenable Configuring Spanning Tree Loop Prote ct Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-75 Example This example shows how to display .
Configuring Spanning Tree Loop Protect Features show spantree disputedbpduthreshold 6-76 Spanning Tr ee Configuration Usage A disputed BPDU is one in which the flag s .
show spantree nonforwardingreason Confi guring Spanning Tree Loop Protect Features Enterasys Matrix DFE-Gold Series Configuratio n Guide 6-77 Parameters None.
Configuring Spanning Tree Loop Protect Feat ures show spantree nonforwar dingreason 6-78 Spanning Tr ee Configuration.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 7-1 7 802.1Q VLAN Configuration This chapter descri bes the Enterasys Matrix syste m’ s capabilities to implement 802.
VLAN Configuration Summary 7-2 802.1Q VLAN Configuration Port Assignment Scheme For information on this device’ s port as signment scheme, refer to “ Por t String Syntax Used in the CLI ” on page 4 ‐ 2.
show vlan Reviewing Existing VLANs Enterasys Matrix DFE-Gold Series Configuration Gu ide 7-3 3. Add the host port and the desired switch port to the egress list for the VLAN created in Step 1.
Reviewing Existing VLANs show vlan 7-4 802.1Q VLAN Configuration Parameters Default s If no options ar e specified, all information related to static and dynamic VLANs will be displayed. Mode Switch command, Read ‐ Only .
show vlan Reviewing Existing VLANs Enterasys Matrix DFE-Gold Series Configuration Gu ide 7-5 Forbidden Egress Ports Ports prevented fr om transmitted frames for this VLAN. Untagged Ports Port s configured to transmit untagged frames for this VLAN. T able 7-2 show vlan Output Det ails (continued) Output.
Creating and Naming Static VLANs set vlan 7-6 802.1Q VLAN Configuration Creating and Naming St atic VLANs Purpose To create a new static VLAN, or to enable or disable exist ing VLAN(s). Commands set vlan Use this command to create a new static IEEE 802.
set vlan name Creating and Naming Static VLANs Enterasys Matrix DFE-Gold Series Configuration Gu ide 7-7 Examples This example shows how to create VLAN 3: Matrix(rw)->se.
Creating and Naming Static VLANs clear vlan name 7-8 802.1Q VLAN Configuration Example This example shows how to remove a stati c VLAN 9 from the device.
show port vlan Assigning Port VLAN IDs (PVIDs) and Ingr ess Filtering Enterasys Matrix DFE-Gold Series Configuration Gu ide 7-9 Assigning Port VLAN IDs (PVIDs) and Ingress Filtering Purpose To ass.
Assigning Port VLAN IDs ( PVIDs) and Ingress Filtering set port vlan 7-10 802.1Q VLAN Configuration Usage PVID determines the VLAN to which all untagged frames re ceived on one or more ports wil l be classified.
clear port vlan Assigning Port VLAN ID s (PVIDs) and Ingress Filtering Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-11 Example This example shows how to add fe.1.1 0 to the port VLAN list of VLAN 4 (PVID 4).
Assigning Port VLAN IDs (PVIDs) and Ingress Filtering set vlan interface 7-12 802.1Q VLAN Configuration Mode Switch command, Read ‐ Only . Example This example shows how to .
clear vlan interface Assigning Port VLAN IDs (PVIDs) and Ingr ess Filtering Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-13 clear vlan interface Use this command to clear the MIB ‐ II interface entry mapped to a VLAN.
Assigning Port VLAN IDs (PVIDs) and Ingr ess Filtering set port ingress filter 7-14 802.1Q VLAN Configuration Example This example shows how to di splay the port ingress filter status for Fast Ethernet ports 10 through 15 in module 1.
show port discard Assigning Port VLAN IDs (PVIDs) and Ingress F iltering Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-15 show port discard Use this command to display the frame discard mode for one or more ports.
Assigning Port VLAN IDs (PVIDs) and Ingress Filtering clear port discard 7-16 802.1Q VLAN Configuration Mode Switch command, Read ‐ Wr i t e .
show port egress Configuring the VLAN Egress List Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-17 Configuring the VLAN Egress List Purpose To assign or remove ports on the egress li st of a particular VLAN.
Configuring the VLAN Egress List set vlan egress 7-18 802.1Q VLAN Configuration Example This example shows you how to show VLAN egress information for Fast Ethernet ports 1 through 3 in module 1.
clear vlan egress Configuring the VLAN Egress List Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-19 Examples This example shows how to add Fast Ethernet ports 5 through 10 in module 1 to the egress list of VLAN 7.
Configuring the VLAN Egress List show vlan dynamic egress 7-20 802.1Q VLAN Configuration show vlan dynamic egress Use this command to display which VLANs are currently enabled for VLAN dynamic egress.
set vlan dynamicegress Configuring the VLAN Egress List Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-21 Example This example shows how to enable the dynamic .
Enabling/Disabling GVRP set vlan dynamicegress 7-22 802.1Q VLAN Configuration Enabling/Disabling GVRP Purpose To dynamically create VLANs acr oss a switched netw ork.
set vlan dynamicegress Enabling/Disabling GVRP Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-23 Figure 7-1 Example of VLAN Propaga tion via GVRP Configuring a VLAN on an 802.1Q switch creates a static VLAN entry .
Enabling/Disabling GVRP show gvrp 7-24 802.1Q VLAN Configuration show gvrp Use this command to display GVRP configuration information.
show garp timer Enabling/Disabling GVRP Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-25 Parameters Default s If port ‐ string is not specif ied, GARP timer inform ation will be displayed for all ports.
Enabling/Disabling GVRP set gvrp 7-26 802.1Q VLAN Configuration set gvrp Use this command to enable or disable GVRP globally on the device or on one or more ports.
set garp timer Enabling/Disabling GVRP Enterasys Matrix DFE-Gold Series Configuratio n Guide 7-27 Example This example shows how to clear GVRP status globally on .
Enabling/Disabling GVRP clear garp timer 7-28 802.1Q VLAN Configuration Parameters Default s At least one optional parameter must be enter ed.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 8-1 8 Policy Classification Configuration This chapter descri bes the Po l ic y Classification set of commands and how to use them.
Configuring Policy Profiles show policy profile 8-2 Policy Classification Conf iguration Configuring Policy Profiles Purpose To review , create, change and remove policy pr ofiles for managing netw ork resources.
set policy profile Configuring Policy Profiles Enterasys Matrix DFE-Gold Series Configuration Gu ide 8-3 Row Status :active Port VID Status :enabled Port VID Override :11 CoS Status :disabled CoS :0 T.
Configuring Policy Profiles set policy profile 8-4 Policy Classification Conf iguration Parameters Default s If optional parameters are not specified, none will be applied. Mode Switch command, Read ‐ Wr i t e .
clear policy profile Configuring Policy Profiles Enterasys Matrix DFE-Gold Series Configuration Gu ide 8-5 clear policy profile Use this command to delete a policy profile ent ry . Synt ax clear policy profile profile-index Parameters Default s None.
Configuring Policy Profiles set policy invali d action 8-6 Policy Classification Conf iguration set policy invalid action Use this command to assign the action the device will apply to an inv alid or unknown policy .
show policy rule Assigning Classification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuration Gu ide 8-7 Assigning Classification Rules to Policy Profiles Purpose To review , assign and unassign classification and admin rules.
Assigning Classifi cation Rules to Policy Profiles show policy rule 8-8 Policy Classification Conf iguration Default s •I f port ‐ string , rule status, storage type, Syslo.
show policy rule Assigning Classification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuration Gu ide 8-9 |PID |Rule Type |Rule Data |Mk|PortStr |RS|ST|S|T|D|VLAN|CoS |U| | 1 |Ether.
Assigning Classifi cation Rules to Policy Profiles show policy capa bility 8-10 Policy Classification Con figuration show policy cap ability Use this command to display all policy classification capabilities supported by you r Enterasys Matrix Series device.
set policy classify Assigning Classifica tion Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-11 |MAC source address | X | X | X | X | X | X | X | X | X | |MAC destina.
Assigning Classifi cation Rules to Policy Profiles set poli cy classify 8-12 Policy Classification Con figuration Parameters Default s If mask is not s pecified, all data bits will be considered relevant. Mode Switch command, Read ‐ Wr i t e .
set policy ru le Assigning Classification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-13 Examples This example shows how to use Ta b l e 8 .
Assigning Classifi cation Rules to Policy Profiles set policy rule 8-14 Policy Classification Con figuration Default s •I f mask is not sp ecified, all data bits will be considered relevant.
clear policy rule Assigning Classification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-15 clear policy rule Use this command to delete one or all policy classification rule entries.
Assigning Classifi cation Rules to Policy Profiles clear policy all-rules 8-16 Policy Classification Con figuration Default s When applicable, data , mask , and port ‐ string must be speci fied for individual rule s to be cleared.
set policy port Assigning Classification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-17 set policy port Use this command to assign an administra tive rule to a port. Synt ax set policy port port-name admin-id Parameters Default s None.
Assigning Classifi cation Rules to Policy Profiles set policy allowed-type 8-18 Policy Classification Con figuration Example This example shows how to show information about policies allow ed on port ge.
clear policy allowed-type Assigning Cl assification Rules to Policy Profiles Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-19 Mode Switch command, Read ‐ Wr i t e .
Assigning Classifi cation Rules to Policy Profiles clear policy port-hit 8-20 Policy Classification Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e .
clear policy port-hit Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-21 Configuring Policy Class of Service (CoS) Using Port-Based or Po licy-Based C.
Configuring Policy Clas s of Service (CoS) clear policy port-hit 8-22 Policy Classification Con figuration Purpose To configure policy ‐ based Class of Service. Commands Define IRL or TXQ resources (data rates or transmit priorities).
show cos state C onfiguring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-23 show cos st ate Use this command to display the Class of Service enable state. Synt ax show cos state Parameters None.
Configuring Policy Clas s of Service (CoS) show cos port-type 8-24 Policy Classification Con figuration show cos port-type Use this command to display Class of Service port type configurations.
show cos port-type Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-25 Gbps 1 DFE-P 4Q 32/4 perc ge.2.1-30; ge.2.1-30; Kbps ge.3.1-30; ge.3.1-30; Mbps ge.4.1-30; ge.4.1-30; Gbps fe.6.1-48; fe.6.1-48; ge.
Configuring Policy Clas s of Service (CoS) show cos unit 8-26 Policy Classification Con figuration show cos unit Use this command to display Class of Service uni ts .
show cos port-config C onfiguring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-27 show cos port-config Use this command to display Class of Service port gr oup configurations.
Configuring Policy Clas s of Service (CoS) set cos port-config irl 8-28 Policy Classification Con figuration Port Group :0 Port Type :1 Assigned Ports :ge.
clear cos port-config irl Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-29 Mode Switch command, Read ‐ Wr i t e .
Configuring Policy Clas s of Service (CoS) clear cos port-config txq 8-30 Policy Classification Con figuration Parameters Default s •I f a name is not specifie d, default names described in Ta b l e 8 ‐ 5 will be applied.
show cos port-resou rce Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-31 Mode Switch command, Read ‐ Wr i t e .
Configuring Policy Clas s of Service (CoS) set cos port-re source irl 8-32 Policy Classification Con figuration set cos port-resource irl Use this command to configure a Class of Service inbound rate limit ing port resource entry .
clear cos port-resource irl Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-33 clear cos port-resource irl Use this command to clear .
Configuring Policy Clas s of Service (CoS) clear cos port-resource txq 8-34 Policy Classification Con figuration Parameters Default s •I f a rate is not specified, port defaults will be applied. •I f not specified, no algorithm wi ll be assigned.
show cos reference Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-35 Mode Switch command, Read ‐ Wr i t e .
Configuring Policy Clas s of Service (CoS) set cos referenc e irl 8-36 Policy Classification Con figuration 0.1 12 txq 3 0.1 13 txq 3 0.1 14 txq 3 0.1 15 txq 3 set cos reference irl Use this command to set a Class of Service inbound rate limiting reference configuration.
set cos reference txq C onfiguring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-37 Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring Policy Clas s of Service (CoS) show cos settings 8-38 Policy Classification Con figuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set cos settings Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-39 6 6 * 12 * 7 7 * 14 * set cos settings Use this command to configure a Class of Service entry .
Configuring Policy Clas s of Service (CoS) show cos violation irl 8-40 Policy Classification Con figuration Default s None. Mode Switch command, Read ‐ Wr i t e .
clear cos all-entries Configuring Policy Class of Service (CoS) Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-41 Parameters Default s If no options are specified, all information for all types of CoS violations will be displayed .
Configuring Policy-Based Routing show route- map 8-42 Policy Classification Con figuration Configuring Policy-Based Routing About Policy-Based Routing Normally , IP packets are forward.
route-map Configuring Policy-Based Routing Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-43 Parameters Default s None. Mode Router command, Glob al configuration: Matrix>Ro uter(config)# Example This example shows how to display route map list 101.
Configuring Policy-Based Routing match ip address 8-44 Policy Classification Con figuration Default s •I f permit or deny is not s pecified, this command will enable route map or policy based routing configuration mode.
set next hop Configuring Policy-Based Routing Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-45 set next hop Use this command to set one or mor e next hop IP address for packets matching an extended access list in a configured route map.
Configuring Policy-Based Routing ip policy route-map 8-46 Policy Classification Con figuration Example This example shows how to display policy information: Matrix>Route.
ip policy priority Configuring Policy-Based Routing Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-47 Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan <vlan_id>))# Usage The “no” form of un ‐ assigns a route map list.
Configuring Policy-Based Routing ip policy load-policy 8-48 Policy Classification Con figuration ip policy load-policy Use this command to configure PBR next hop behavior .
ip policy pinger Configuring Policy-Based Routing Enterasys Matrix DFE-Gold Series Configuratio n Guide 8-49 Default s •I f not specified, interval will be set to 3 seconds. •I f not specified, retries wil l be set to 3.
Configuring Policy-Based Routing ip policy pinger 8-50 Policy Classification Con figuration.
Enterasys Matrix DFE-Gold Series Configuration Gu ide 9-1 9 IGMP Configuration This chapter descri bes the IGMP Configuration set of commands and how to use them.
IGMP Configuration Summary show igmp enable 9-2 IGMP C onfiguration Howeve r , note that IGMP neither alters nor routes any IP multicast packets.
set igmp enable Enabling / Disabling IGMP Enterasys Matrix DFE-Gold Series Configuration Gu ide 9-3 Mode Switch command, Read ‐ Only . Example This example shows how to d.
Enabling / Disabling IGMP set igmp disable 9-4 IGMP C onfiguration Example This example shows how to disable IGMP on VLAN 104: Matrix(rw)->set igmp disable 104.
show igmp query Configuring IGMP Enterasys Matrix DFE-Gold Series Configuration Gu ide 9-5 Configuring IGMP Purpose To display and set IGMP configuration parameters, includ.
Configuring IGMP set igmp query-enable 9-6 IGMP C onfiguration Default s None. Mode Switch command, Read ‐ Only . Example This example shows how to display the .
show igmp grp-full-action Conf iguring IGMP Enterasys Matrix DFE-Gold Series Configuration Gu ide 9-7 Mode Switch command, Read ‐ Wr i t e . Example This example shows how to.
Configuring IGMP show igmp config 9-8 IGMP C onfiguration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to flood multicast frames to .
set igmp config Configuring IGMP Enterasys Matrix DFE-Gold Series Configuration Gu ide 9-9 set igmp config Use this command to configure IGMP settings on one or more VLANs.
Configuring IGMP set igmp delete 9-10 IGMP C onfiguration Example This example shows how to set the IGMP query interv al time to 250 seconds on .
show igmp stat ic Configuring IGMP Enterasys Matrix DFE-Gold Series Configuratio n Guide 9-11 Example This example shows how to display IGMP group information for VLAN 105.
Configuring IGMP set igmp remove-static 9-12 IGMP C onfiguration Default s If not specified, the static entry will be created and not modified. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to add port fe.
show igmp protocols Configuring IGMP Enterasys Matrix DFE-Gold Series Configuratio n Guide 9-13 show igmp protocols Use this command to display the binding of IP protocol id to IGM P classification. Synt ax show igmp protocols Default s None.
Configuring IGMP clear igmp protocols 9-14 IGMP C onfiguration Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to change IGM.
show igmp reporters Configuring IGMP Enterasys Matrix DFE-Gold Series Configuratio n Guide 9-15 Example This example shows how to display igmp information for vlan 12: Matrix(rw)->show igmp vlan 12 IGMP Vlan 12 Info IGMP query state : Enable d QueryInterval(sec.
Configuring IGMP show igmp flows 9-16 IGMP C onfiguration lag.0.2 239.255.12.43 1 Any 253 DYNAMIC lag.0.2 239.255.255.250 1 Any 255 DYNAMIC lag.0.2 239.
show igmp number-grou ps Configuring IGMP Enterasys Matrix DFE-Gold Series Configuratio n Guide 9-17 Default s None. Mode Switch command, Read ‐ Only .
Configuring IGMP show igmp number-groups 9-18 IGMP C onfiguration Example This example shows how to display the number of multicast groups supported by the device.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 10-1 10 System Logging Configuration This chapter descri bes system logging commands and how to use them.
Configuring System Logging show logging all 10-2 System Logging Co nfiguration show logging all Use this command to display all configuration information for system logging. Synt ax show logging all Parameters None.
show logging ser ver Configuring System Logging Enterasys Matrix DFE-Gold Series Configuratio n Guide 10-3 1 80.80.80.252 local7 debugging( 8) N-Series 514 enabled Defaults: local4 debugging( 8) 514 S.
Configuring System Logging set logging server 10-4 System Logging Co nfiguration Default s If index is not specif ied, all Syslo g server inf ormation will be displayed. Mode Switch command, Read ‐ Only .
clear logging server Configuring System Logging Enterasys Matrix DFE-Gold Series Configuratio n Guide 10-5 Default s •I f ip ‐ addr is not specifie d, an entry in t.
Configuring System Logging set logging default 10-6 System Logging Co nfiguration Default s None. Mode Switch command, Read ‐ Only . Example This command shows how to display the Syslog serv er default va l u e s .
clear logging default Configuring System Logging Enterasys Matrix DFE-Gold Series Configuratio n Guide 10-7 Example This example shows how to set the Syslog default .
Configuring System Logging show logging application 10-8 System Logging Co nfiguration Mode Switch command, Read ‐ Only . Usage Mnemonics will var y depe nding on the number and types of applications running on your system.
set logging application Configuring System Logging Enterasys Matrix DFE-Gold Series Configuratio n Guide 10-9 90 SNMP 6 1-8 1(emergencies) 2(alerts) 3(cr itical) 4(errors) 5(warnings) 6(no tifications) 7(information) 8(debugging) Ta b l e 1 0 ‐ 2 provides an explanation of the command output.
Configuring System Logging set logging application 10-10 System Logg ing Configuration Default s •I f level is not specified, none will be applied. •I f server is not specified, messages will be sent to all Syslog serv ers.
clear logging application Con figuring System Logging Enterasys Matrix DFE-Gold Series Configur ation Guide 10-11 clear logging application Use this command to reset the loggin.
Configuring System Logging set logging local 10-12 System Logg ing Configuration set logging local Use this command to configure log messages to the console and a persistent file. Synt ax set logging local console { enable | disable } file { enable | disable } Parameters Default s None.
set logging here Configuring System Logging Enterasys Matrix DFE-Gold Series Configur ation Guide 10-13 set logging here Use this command to enable or disable the current CLI session as a Sy slog destinat ion.
Configuring System Logging show logging buffer 10-14 System Logg ing Configuration show logging buffer Use this command to display the last 256 messages logge d on all blades. Synt ax show logging buffer Parameters None.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 11-1 11 Network Monitoring Configuration This chapter descri bes Network Monitoring comm ands and how to use them.
Monitoring Network Events and Status show history 11-2 Network Mo nitoring Configuration Parameters None. Default s None. Mode Switch command, Read ‐ Only .
set history Monitoring Network Events and Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 11-3 set history Use this command to set the size of the history buffer .
Monitoring Network Events and Status ping 11-4 Network Mo nitoring Configuration Example This example shows how to display statistics for all the current ac.
ping Monitoring Network Events and Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 11-5 Mode Switch command, Read ‐ Wr i t e . Examples Matrix(rw) ‐ >ping 134.141.89.29This example shows how to ping IP address 134.
Monitoring Network Events and Status show users 11-6 Network Mo nitoring Configuration show users Use this command to display information about the active console port or Te l n e t session(s) logged in to the switch.
disconnect Monitoring Network Events and Status Enterasys Matrix DFE-Gold Series Configuratio n Guide 11-7 Example This example shows how to tell all users about a system reset: Matrix(rw)->tell all system reset sc heduled for 1 p.
Configuring SMON show smon priority 11-8 Network Mo nitoring Configuration Configuring SMON Purpose To configure SMON (Switched Network Monitoring) on the device. Commands show smon priority Use this command to display SMON user priority stati stics.
set smon priority Configuring SMON Enterasys Matrix DFE-Gold Series Configuratio n Guide 11-9 ------------------------ Interface = ge.3.14 Owner = none Creation = 0 days 0 hours 6 minutes 39 seconds S.
Configuring SMON show smon vlan 11-10 Networ k Monitoring Configuration Parameters Default s If port ‐ string is not specif ied, priorit y statistics will be cleared on all ports. Mode Switch command, Read ‐ Wr i t e .
set smon vlan Configuring SMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-11 Status = enabled -------------------- VLAN 1 Packets Octets Total 8011072 2070785503 Overflow 0 0 NonUnicast .
Configuring SMON clear smon vlan 11-12 Networ k Monitoring Configuration Parameters Default s If port ‐ string is not specif ied, VLAN statistics counting configurations will be cleared for all ports.
clear smon vlan Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-13 Configuring RMON RMON Monitoring Group Functions and Commands RMON (Remote Network Monitoring) .
Configuring RMON clear smon vlan 11-14 Networ k Monitoring Configuration Host Records statistics assoc iated with each host discovered on the network. Host address, packets and bytes received and transmitted, and broadcast, multicast and error packet s.
show rmon stats Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-15 show rmon st ats Use this command to display RMON statistics measured for one or more ports.
Configuring RMON show rmon stats 11-16 Networ k Monitoring Configuration T able 1 1-3 show rmon st at s Output Det ails Output... W hat it displays... Port Port designatio n. Owner Name of the entity that configured thi s entry . Mon itor is default. Data Source Data source of t he statistics being displayed.
set rmon stats Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-17 set rmon st at s Use this command to configure an RMON statistics entry .
Configuring RMON show rmon history 11-18 Networ k Monitoring Configuration Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to delete.
set rmon history Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-19 Sample 2304 Interval Start: 0 d ays 19 hours 11 minutes 35 seconds Drop Events = 0 Undersize Pkts = 0 Octe.
Configuring RMON show rmon alarm 11-20 Networ k Monitoring Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to .
set rmon alarm properties Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-21 Sample Type = delta Startup Alarm = rising Interval = 30 Value = 0 Rising Threshold = 1 Falling T.
Configuring RMON set rmon alarm status 11-22 Networ k Monitoring Configuration Default s •i n t e r v a l ‐ 3600 seconds •t y p e ‐ absolute •s t a r t u p ‐ risin .
clear rmon alarm Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-23 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring RMON show rmon event 11-24 Networ k Monitoring Configuration show rmon event Use this command to display RMON event entry properties.
set rmon event properties Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-25 set rmon event properties Use this command to configure an RMON event entry , or to create a new event entry with an unused event index number .
Configuring RMON clear rmon event 11-26 Networ k Monitoring Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Usage An RMON event entry can .
show rmon host Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-27 show rmon host Use this command to display RMON properties and statistics associated with each host discovere d on the network.
Configuring RMON set rmon host properties 11-28 Networ k Monitoring Configuration Out Octets 136 Broadcast Pkts 0 Multicast Pkts 0 set rmon host properties Use this command to configure an RMON host entry .
clear rmon host Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-29 Example This example shows how to enable RMON host entry 1: Matrix(rw)->set rmon host status 1 e nable clear rmon host Use this command to delete an RMON host entry .
Configuring RMON show rmon topN 11-30 Networ k Monitoring Configuration Example This example shows how to display all RMON To p N properties and statistics.
set rmon topN properties Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-31 set rmon topN properties Use this command to configure an RMON topN entry (report).
Configuring RMON clear rmon topN 11-32 Networ k Monitoring Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to .
show rmon matrix Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-33 Parameters Default s •I f port ‐ string is not specif ied, information about all ports wi ll be display ed.
Configuring RMON set rmon matrix properties 11-34 Networ k Monitoring Configuration set rmon matrix properties Use this command to configure an RMON matrix entry .
clear rmon matrix Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-35 Mode Switch command, Read ‐ Wr i t e . Example This example shows how to en.
Configuring RMON set rmon channel 11-36 Networ k Monitoring Configuration Example This example shows how to display RMON channel information for fe .
clear rmon channel Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-37 Default s •I f an action is not specif ied, packets will be accepted on filter matches. •I f not specified, contr ol will be set to off .
Configuring RMON set rmon filter 11-38 Networ k Monitoring Configuration Parameters Default s If no options are specified, information for all filter entries will be display ed. Mode Switch command, Read ‐ Only .
clear rmon filter Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-39 Default s •I f owner is not specif ied, it will be set to monitor . •I f no other options are specifie d, none (0) will be applied.
Configuring RMON show rmo n capture 11-40 Networ k Monitoring Configuration show rmon capture Use this command to display RMON capture entries and associated buffer control entries.
set rmon capture Configuring RMON Enterasys Matrix DFE-Gold Series Configur ation Guide 11-41 set rmon capture Use this command to configure an RMON capture entry , or to enable or disable an existing ent ry .
Configuring RMON clear rmon capture 11-42 Networ k Monitoring Configuration clear rmon capture Use this command to clears an RMON capture entry . Synt ax clear rmon capture index Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
Enterasys Matrix DFE-Gold Series Configuratio n Guide 12-1 12 Network Address and Route Management Configuration This chapter descri bes switch ‐ related netw ork address and route management commands and how to use them.
Managing Switch Network Addresses and Routes show arp 12-2 Network Add ress and Route Management Configuration show arp Use this command to display the switch’ s ARP table. Synt ax show arp Parameters None. Default s None.
set arp Managing Switch Network Addresses and Routes Enterasys Matrix DFE-Gold Series Configuratio n Guide 12-3 set arp Use this command to add mapping entries to the switch’ s ARP table.
Managing Switch Network Addresses and Routes show rad 12-4 Network Add ress and Route Management Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to delete entry 10.
show ip route Managing Switch Network Addresses and Routes Enterasys Matrix DFE-Gold Series Configuratio n Guide 12-5 Default s None. Mode Switch command, Read ‐ Wr i t e .
Managing Switch Network Addresses and Routes traceroute 12-6 Network Add ress and Route Management Configuration traceroute Use this command to display a hop ‐ by ‐ hop path through an IP network from the device to a specific destination host.
traceroute Managing Switch Network Addresses and Routes Enterasys Matrix DFE-Gold Series Configuratio n Guide 12-7 Default s •I f not specified, waittime will be set to 5 seconds. •I f not specified, first ‐ tt l will be set to 1 second.
Managing Switch Network Addresses and Routes set ip route 12-8 Network Add ress and Route Management Configuration Example This example shows how to use traceroute to display a round trip path to host 192.
show port mac Managing Switch Network Addresses and Routes Enterasys Matrix DFE-Gold Series Configuratio n Guide 12-9 Default s None. Mode Switch command, Read ‐ Wr i t e .
Managing Switch Network Addresses and Routes show mac 12-10 Networ k Address and Route Management Con figuration show mac Use this command to display the timeout period .
set mac Managing Switch Network Addresses and Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 12-11 Matrix(rw)->show mac port-string fe. 1.3 MAC Address FID Port Type Status ----------------- ---- ------------- ------- ------- 00-01-F4-32-88-C5 0 fe.
Managing Switch Network Addresses and Routes clear mac 12-12 Networ k Address and Route Management Con figuration Default s If port ‐ string is not defined with the set mac multicast command, then it will apply to all ports.
show newaddrtraps Managing Switch Ne twork Addresses and Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 12-13 Parameters None. Default s None, except those noted abov e.
Managing Switch Network Addresses and Routes set newaddrtraps 12-14 Networ k Address and Route Management Con figuration Example This example shows how to display the status of MAC address traps on ge.
set movedaddrtrap Managing Switch Network Addre sses and Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 12-15 Parameters Default s If port ‐ string is not specif ied, MAC addres s traps for all ports will be display ed.
Managing Switch Network Addresses and Routes set movedaddrtrap 12-16 Networ k Address and Route Management Con figuration Example This example shows how to globally enable .
Enterasys Matrix DFE-Gold Series Configuratio n Guide 13-1 13 SNTP Configuration This chapter descri bes Simple Netw ork Time Protocol (SNTP) commands and how to use them.
Configuring Simple Network Time Protocol (SNTP) show sntp 13-2 SNTP Con figuration show sntp Use this command to display SNTP client settings. Synt ax show sntp Parameters None. Default s None. Mode Switch command, Read ‐ Only .
set sntp clien t Configuring Simple Network Time Protocol (SNTP) Enterasys Matrix DFE-Gold Series Configuratio n Guide 13-3 set sntp client Use this command to set the SNTP operation mode. Synt ax set sntp client { broadcast | unicast | disab le } Parameters Default s None.
Configuring Simple Network Time Protocol (SNTP) clear sntp client 13-4 SNTP Con figuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to enable.
clear sntp server C onfiguring Simple Network Time Protocol (SNTP) Enterasys Matrix DFE-Gold Series Configuratio n Guide 13-5 Example This example shows how to set the serv er at IP address 10.21.1.100 as an SNTP serv er: Matrix(rw)->set sntp server 10.
Configuring Simple Network Time Protocol (SNTP) clear sntp broadcast delay 13-6 SNTP Con figuration Example This example shows how to set the SNTP broadcast delay .
clear sntp poll-interval Configuring Simple Net work Time Protocol (SNTP) Enterasys Matrix DFE-Gold Series Configuratio n Guide 13-7 clear sntp poll-interval Use this command to clear the poll interval betw een unicast SNTP requests.
Configuring Simple Network Time Protocol (SNTP) set sntp poll-timeout 13-8 SNTP Con figuration Parameters None. Default s None. Mode Switch command, Read ‐ Wr i t e .
show timezone Config uring Simple Network Time Protocol (SNTP) Enterasys Matrix DFE-Gold Series Configuratio n Guide 13-9 Mode Switch command, Read ‐ Wr i t e .
Configuring Simple Network Time Protocol (SNTP) clear timezone 13-10 SNTP Co nfiguration Default s If offset hours or minutes are not specified, none will be applied. Mode Switch command, Read ‐ Wr i t e .
Enterasys Matrix DFE-Gold Series Configuratio n Guide 14-1 14 Node Alias Configuration This chapter descri bes node alias commands and how to use them.
Configuring Node Aliases show nodealias mac 14-2 Node Alias Con figuration Default s If port ‐ string is not specif ied, node alias properties will be dis played for all ports. Mode Switch command, Read ‐ Only .
show nodealias mac Configuring Node Aliases Enterasys Matrix DFE-Gold Series Configuratio n Guide 14-3 Parameters Default s •I f protocol is not specified , node alias entri es for all protocols will be displayed.
Configuring Node Aliases show nodealias protocol 14-4 Node Alias Con figuration Example This example shows how to display node alias entries for BPDU traffic on MAC address es beginning with 00 ‐ e0.
show nodealias config Configuring Node Aliases Enterasys Matrix DFE-Gold Series Configuratio n Guide 14-5 Parameters Default s •I f ip ‐ address is not specified for the IP protocol, IP ‐ related entries will be displayed from all source addresses.
Configuring Node Aliases set nodealias 14-6 Node Alias Con figuration Default s If port ‐ string is not specif ied, node alias configurations will be displ ayed for all ports. Mode Switch command, Read ‐ Only .
set nodealias maxentries Configuring Node Aliases Enterasys Matrix DFE-Gold Series Configuratio n Guide 14-7 Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring Node Aliases clear nodealias config 14-8 Node Alias Con figuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear all node alias entries on fe.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 15-1 15 NetFlow Configuration This chapter descri bes NetFlow commands and how to use them. Configuring NetFlow NetFlow is a protocol developed for collecting IP traffic information.
Configuring NetFlow 15-2 NetF low Configuration •I t has accumulated the maximum number of NetFlow records per packet, which is 30, or •.
show netflow Configuring NetFlow Enterasys Matrix DFE-Gold Series Configuratio n Guide 15-3 show net flow Use this command to display NetFlow configuration information and/or statistics.
Configuring NetFlow set netflow cache 15-4 NetF low Configuration Export Interval: 30 (min) Number of Entries: 196607 Inactive Timer: 40 (sec) Template Refresh-rate: 20 (packets) Template Timeout: 30 (min) Enabled Ports: ----------------- ge.
set netflow export-destination Configuring N etFlow Enterasys Matrix DFE-Gold Series Configuratio n Guide 15-5 Default s None. Mode Switch command, Read ‐ Wr i t e . Usage When this command is executed, NetFlow is effectiv ely disabled on the system.
Configuring NetFlow se t netflow export-interval 15-6 NetF low Configuration Parameters Default s Since only one collector address per Enterasys Matrix system is supported, entering the IP address and UDP port information is not required.
clear netflow export-interval Configuring N etFlow Enterasys Matrix DFE-Gold Series Configuratio n Guide 15-7 clear net flow export-interval Use this command to clear NetFlow export interv al to its def ault of 30 minutes.
Configuring NetFlow clear netflow port 15-8 NetF low Configuration clear net flow port Use this command to return a port to the default NetFlow collection state of disabled. Synt ax clear netflow port port-string Parameters Default s None.
clear netflow export-version Configuring NetFlow Enterasys Matrix DFE-Gold Series Configuratio n Guide 15-9 Example This example shows how to set the flow record fo.
Configuring NetFlow set netflow template 15-10 NetF low Configuration Parameters Default s At least one of the ref resh ‐ rate or ti meout parameters must be specified, although both can be specified on one command line.
clear netflow template Configuring NetFlow Enterasys Matrix DFE-Gold Series Configur ation Guide 15-11 clear net flow template Use this command to reset the Ve r s i o n 9 template refresh rate and/or timeout va l u es to their default val u e s.
Configuring NetFlow clear netflow template 15-12 NetF low Configuration.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 16-1 16 IP Configuration This chapter descri bes the Internet Protocol (IP) configuration set of commands and how to use them.
Configuring Routing Interface Settings show interface 16-2 IP Configuration For details on how to enable all router CLI configuration modes, refer back to Ta b l e 2 ‐ 9 . For details on configur ing routing protocols, refer to Chapter 21 .
interface Configuring Routing Inter face Settings Enterasys Matrix DFE-Gold Series Configuratio n Guide 16-3 Mode Router command, Any router mode. Example This example shows how to display information for all interfaces configured on the router .
Configuring Routing Interface Settings ip ecm-forwarding-algorithm 16-4 IP Configuration details on configur ation modes supported by the Enterasys Matr ix Series .
show ip interfac e Configuring Routing Interface Settings Enterasys Matrix DFE-Gold Series Configuratio n Guide 16-5 show ip interface Use this command to display information, .
Configuring Routing Interface Settings ip address 16-6 IP Configuration ip address Use this command to set, remove, or disable a primary or secondary IP address for an interface.
no shutdown C onfiguring Routing Interface Settings Enterasys Matrix DFE-Gold Series Configuratio n Guide 16-7 Usage Each Enterasys Mat rix Series routing module or standal.
Managing Router Configuration Files show running-config 16-8 IP Configuration Managing Router Configuration Files Each Enterasys Matrix Series de vice provides a single .
write Managing Router Configuration Files Enterasys Matrix DFE-Gold Series Configuratio n Guide 16-9 ip address 192.168.100.1 255.255.2 55.255 no shutdown ! interface vlan 10 ip address 99.99.2.10 255.255.255. 0 no shutdown ! router ospf 1 network 99.
Managing Router Configuration Files no ip routing 16-10 IP Configura tion interface vlan 2 iP Address 182.127.62.1 255.255.255 .0 no shutdown exit router rip network 182.
no ip routing Performing a Basic Router Configuration Enterasys Matrix DFE-Gold Series Configur ation Guide 16-11 Performing a Basic Router Configuration Using Router-Only Config Files Although th.
Reviewing and Configuring the ARP Table show ip arp 16-12 IP Configura tion 2. Copy the config file to a place where it can be edited with a file editing program.
show ip arp Reviewing and Configuring the ARP Table Enterasys Matrix DFE-Gold Series Configur ation Guide 16-13 Parameters Default s If no parameters are specified, all entries in the ARP cache will be displayed.
Reviewing and Configuring the ARP Table arp 16-14 IP Configura tion arp Use this command to add or remove perman ent (static) ARP table entries. Synt ax arp ip-address mac-address arpa no arp ip-address Parameters Default s None.
ip gratuitous-arp Reviewin g and Configuring the ARP Table Enterasys Matrix DFE-Gold Series Configur ation Guide 16-15 ip gratuitous-arp Use this command to override the normal ARP updating process, that occurs by default.
Reviewing and Configuring the ARP Table ip proxy-arp 16-16 IP Configura tion Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage This .
ip mac-address Reviewin g and Configuring the ARP Table Enterasys Matrix DFE-Gold Series Configur ation Guide 16-17 Example This example shows how to enable pro xy ARPMatri.
Reviewing and Configuring the ARP Table clear arp-cache 16-18 IP Configura tion Parameters Default s None. Mode Router command, Glob al configuration: Matrix>Ro uter(config)# Usage The device can support up to 2000 outstanding unresolved ARP en tries.
ip directed-broadcast Configuring Broadcast Settings Enterasys Matrix DFE-Gold Series Configur ation Guide 16-19 Configuring Broadcast Settings Applying DHCP/BOOTP Relay DHCP/BOOTP relay functionality is applied with the help of IP broadcast forw arding.
Configuring Broadcast Settings ip forward-pr otocol 16-20 IP Configura tion Usage The “no” form of this command disables IP directed broadcast globally .
ip helper-address Configuring Broadcast Settings Enterasys Matrix DFE-Gold Series Configur ation Guide 16-21 Example This example shows how to enable forw arding of Dom.
Reviewing IP Traffic and Configuring Routes show ip protocols 16-22 IP Configura tion Reviewing IP T raffic and Configuring Routes Purpose To review IP protocol information about .
show ip traffic Reviewing IP Tr affic and Configuring Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 16-23 Example This example shows how to display IP protocol information. In this case, the routing protocol is RIP (Routing Information Protocol).
Reviewing IP Traffic and Configuring Routes clear ip stats 16-24 IP Configura tion Frags: 0 reassembled, 0 timeouts 0 couldn't reassemble 0 fragmented, 0 c ouldn't fragment Bcast: 1 received.
show ip route Reviewing IP Traffic and Configuring Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 16-25 Example This example shows how to clear all IP tra.
Reviewing IP Traffic and Configuring Routes ip route 16-26 IP Configura tion Example This example shows how to display all IP route information.
ip icmp Reviewing IP Traffic and Configuring Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 16-27 Examples This example shows how to set IP address 10.1.2.3 as the next hop gateway to de stination address 10.
Reviewing IP Traffic and Configuring Routes ping 16-28 IP Configura tion ping Use this command to test routing network connectivity by sending IP ping requests. Synt ax ping ip-address Parameters Default s None.
traceroute Reviewing IP Traffic and Configuring Routes Enterasys Matrix DFE-Gold Series Configur ation Guide 16-29 Parameters Default s None. Mode Router command, Privileged EXEC: Matr.
Configuring Debug IP Packet debug ip packet access-group 16-30 IP Configura tion Configuring Debug IP Packet Purpose Debug IP packet is an IP based packet monitor t.
debug ip packet restart Configuring Debug IP Packet Enterasys Matrix DFE-Gold Series Configur ation Guide 16-31 Mode Router command, Router configuration: Matrix>Router(config)# Rou.
Configuring Debug IP Packet show debugging 16-32 IP Configura tion Parameters None. Default s None. Mode Router command, Router configuration: Matrix>Router(config)# Router Exec.
no debug ip packet Configuring Debug IP Packet Enterasys Matrix DFE-Gold Series Configur ation Guide 16-33 Parameters None. Default s None. Mode Router command, Router configuration: M.
Configuring Debug IP Packet no debug ip packet 16-34 IP Configura tion.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 17-1 17 PIM Configuration This chapter descri bes the Protocol Independent Multicast (PIM) configura tion set of commands and how to use them.
Configuring PIM ip pim sparse mode 17-2 PIM Configuration ip pim sp arse mode Use this command to enable Protocol Independent Multicast (PIM) Sparse Mode (SM) on a routing interface. Synt ax ip pim sparse-mode no ip pim sparse-mode Parameters None.
ip pim dr-priority Configuring PIM Enterasys Matrix DFE-Gold Series Configuratio n Guide 17-3 Parameters Default s •A hash ‐ mask ‐ length va l ue of 30 will be automatically applied. •I f priority is not specified, 1 wil l be applied.
Configuring PIM ip pim rp-address 17-4 PIM Configuration Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage The “no” form of this command disables the DR functionality .
ip pim rp-candidate Configuring PIM Enterasys Matrix DFE-Gold Series Configuratio n Guide 17-5 ip pim rp-candidate Use this command to enable the router to advertise itself as a PIM candidate rendezvous point (RP) to the BSR.
Configuring PIM show ip pim interface 17-6 PIM Configuration Mode Router command, Privileged EXEC: Matrix>Router# Example This example shows how to display BootStrap Router (BSR) information: Matrix>Router#show ip pim bsr PIMv2 Elected Bootstrap Router Infor mation: BSR Address: 10.
show ip pim neighbo r Configuring PIM Enterasys Matrix DFE-Gold Series Configuratio n Guide 17-7 Parameters Default s If not specified, informatio n about all PIM interfaces will be displayed.
Configuring PIM show ip pim rp 17-8 PIM Configuration Parameters Default s If not specified, informatio n about all PIM interfaces will be displayed.
show ip pim rp Configuring PIM Enterasys Matrix DFE-Gold Series Configuratio n Guide 17-9 Parameters Default s If no optional parameters are spe cified, all active RP s will be di splayed.
Configuring PIM show ip pim rp-hash 17-10 PIM Configura tion show ip pim rp-hash Use this command to display the rendezvous point (RP) that is being selected for a specified group. Synt ax show ip pim rp-hash group-address Parameters Default s None.
show ip mforward Configuring PIM Enterasys Matrix DFE-Gold Series Configur ation Guide 17-11 Example This example shows a portion of the IP multicast routing table display .
Configuring PIM show ip rpf 17-12 PIM Configura tion Example This example shows a porti on of the IP multicast forw arding table display: Matrix>Router#show ip mforward IP Multicast Forwarding Table 1 of 8: (63.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 18-1 18 Network Address T ranslation (NA T) Configuration This chapter descri bes the Network Address T ranslation (NA T) conf iguration set of commands and how to use them.
Configuring Network Address Translation (NAT) 18-2 Network Add ress Translation (NAT) Configuration NA T wor k s with DNS by having the DNS Application Specific .
ip nat Configuring Network Address Translation (NAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 18-3 ip nat Use this command to enable NA T on this interf ace. Synt ax ip nat { inside | outside } no ip nat { inside | outside } Parameters Default s None.
Configuring Network Address Translation (NAT) ip nat inside source list 18-4 Network Add ress Translation (NAT) Configuration Parameters Default s If no netmask or prefix ‐ length is specif ied, all addresses in the range are used.
ip nat inside source static (NAT) Confi guring Network Address Tra nslation (NAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 18-5 Mode Router command, Glob al configuration: .
Configuring Network Address Translation (NAT) ip nat inside source st atic (NAPT) 18-6 Network Add ress Translation (NAT) Configuration ip nat inside source st atic (NAPT) Use this command to enable static NAPT translation of inside source addresses.
ip nat secure-plus Configuring Network Address Translation (NAT ) Enterasys Matrix DFE-Gold Series Configuratio n Guide 18-7 Default s None. Mode Router command, Glob al configuration: .
Configuring Network Address Translation (NAT) ip nat translation max-entries 18-8 Network Add ress Translation (NAT) Configuration ip nat translation max- entries Use this command to configure the maximum number of translation entries.
show ip nat translatio ns Configuri ng Network Address Translation (NAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 18-9 Default s If seconds is not specif ied, see the parameter ta ble above fo r the default va l u e .
Configuring Network Address Translation (NAT) show ip nat statistics 18-10 Networ k Address Translation (NAT) Configur ation tcp 81.1.1.1:1030 172. 111.1.4:50025 DynOver 3 tcp 81.1.1.1:1031 172. 111.1.4:50026 DynOver 3 tcp 81.1.1.1:1032 172. 111.1.4:50027 DynOver 1 tcp 81.
show ip nat statistics Configuring Network Address Translation (NAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 18-11 Examples This example displays the NA T statistics .
Configuring Network Address Translation (NAT) clear ip nat translation 18-12 Networ k Address Translation (NAT) Configur ation access-list 35 refcount 28 pool vlan 3000: netmask 0.
clear ip nat translation inside (NAPT) Confi guring Netw ork Address Translation (NAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 18-13 Usage This command clears an active translation.
Configuring Network Address Translation (NAT) set router lim its (NAT) 18-14 Networ k Address Translation (NAT) Configur ation set router limit s (NA T) Use this command to set NA T configuration limits.
show router limits (NAT) Configuri ng Network Address Tra nslation (NAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 18-15 Example This example sets the maximum NA T .
Configuring Network Address Translati on (NAT) clear router limits (NAT) 18-16 Networ k Address Translation (NAT) Configur ation Route Table Limit - 12000 (default) TWCB maximum Bindings - 32000 (defa.
clear router limits (NAT) Configuri ng Network Address Translation (NAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 18-17 Example This example resets the NA T cache .
Configuring Network Address Translati on (NAT) clear router limits (NAT) 18-18 Networ k Address Translation (NAT) Configur ation.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 19-1 19 LSNA T Configuration This chapter describes the Load Sharing Network Addres s T ranslation (LSNA T) configuration set of commands and how to us e them.
Configuring Load Sharing Networ k Address Translatio n (LSNAT) 19-2 LSNAT Co nfiguration •W h e n different virtual serv er IPs (VIPs) share the sa me real serv er in different server farms, the persistence level must be set the same.
Configuring Load Sharing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 19-3 wou ld only require the use of one binding hardw are resource (instead of one per service per client).
Configuring Load Sharing Networ k Address Translatio n (LSNAT) 19-4 LSNAT Co nfiguration the UDP port. If the server responds with an ICMP “P ort Unreacha.
Configuring Load Sharing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 19-5 Purpose To review and configure Load Sharing Network Addr ess T ranslation (LSNA T).
Configuring Load Sharing Network Address Tr anslatio n (LSNAT) show ip slb serverfarms 19-6 LSNAT Co nfiguration show ip slb serverfarms Use this command to display server load balancing se rver farm information.
ip slb ftpctrlport Configuring Load Shari ng Network Address Translation (LSNAT ) Enterasys Matrix DFE-Gold Series Configuratio n Guide 19-7 Parameters Default s If no parameter is specified, summary information for all configured server farms will be display ed.
Configuring Load Sharing Network Addres s Tran slation (LSNAT) ip slb serverfarm 19-8 LSNAT Co nfiguration Example This example shows how to specify port 46 as the .
predictor Configuring Load Sharing Ne twork Address Tra nslation (LSNAT) Enterasys Matrix DFE-Gold Series Configuratio n Guide 19-9 Default s None. Mode Router command, SLB Serv er Far.
Configuring Load Sharing Network A ddress Translatio n (LSNAT) sticky 19-10 LSNAT C onfiguration Example This example shows how to specify Least Connections as the .
show ip slb reals Configuring Load Shari ng Netw ork Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-11 Parameters Default s If no parameter is specified, summary information ab out all configured server farms wil l be display ed.
Configuring Load Sharing Network Address Tran slation (LSNAT) show ip slb reals 19-12 LSNAT C onfiguration Current Connections on this real server: 0 Current state of thi s real server: UP Maximum Con.
inservice (real server) Configuring Load Shar ing Network Address Translation (LSNAT ) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-13 inservice (real server) Use this command to enable a real LSNA T serv er .
Configuring Load Sharing Network Address Tr an slation (LSNAT) faildetect (real server) 19-14 LSNAT C onfiguration Parameters Default s If not specified, ping will be chosen as the fail detection type. Unless the UDP option is specified, app defaults to TCP .
faildetect acv-command Configuring Load Shar ing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-15 Matrix>Router(config-slb-real)#faild etect type app .
Configuring Load Sharing Network Address Tran slation (LSNAT) faildetect acv-reply 19-16 LSNAT C onfiguration faildetect acv-reply Use this command to set the expected va l id at i o n ACV reply string from the server application port.
faildetect read-till-index Configuring Load Shar ing Network Address Translation (LSNAT ) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-17 Usage A Carriage Return / Line .
Configuring Load Sharing Network A ddress Translation (LSNAT) maxconns 19-18 LSNAT C onfiguration maxconns Use this command to limit the number of connections to a real LSNA T server . Synt ax maxconns maximum-number no maxconns Parameters Default s None.
show ip slb vservers Configuring Load Shar ing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-19 Mode Router command, SLB Real Serv er .
Configuring Load Sharing Network Address Tran slation (LSNAT) show ip slb vservers 19-20 LSNAT C onfiguration five 3.3.3.3 80 ten TCP 41 IS test 192.169.
ip slb vserver Configuring Load Sharing Network Address Translation (LSNAT ) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-21 ip slb vserver Use this command to identify .
Configuring Load Sharing Network Address Tran slation (LSNAT) serverfarm (Virtual Server) 19-22 LSNAT C onfiguration serverfarm (V irtual Server) Use this command to associate a virtual server with an LSNA T server farm.
virtual Configuring Load Sharing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-23 Parameters Default s If a TCP servi ce name is not specified, none will be applied.
Configuring Load Sharing Network Address Tran slation (LSNAT) inservice (virtual server) 19-24 LSNAT C onfiguration inservice (virtual server) Use this command to enable a virtual LSNA T server . Synt ax inservice no inservice Parameters None.
persistence level Configuring Lo ad Sharing Network Address Translation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-25 Parameters Default s None.
Configuring Load Sharing Network Addres s Tran slation (LSNAT) persistence level 19-26 LSNAT C onfiguration Parameters Default s If not specified, persistence level is set to TCP .
allow accessservers Configuring Load Shari ng Network Address Tra nslation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-27 This example shows how to use sticky session persistence, in conjunction with the sticky server farm parameter .
Configuring Load Sharing Network Address Tr anslatio n (LSNAT) ip slb allowaccess_all 19-28 LSNAT C onfiguration Example This example shows how to allow clients at 10.
show ip slb conns Configuring Load Shari ng Network Address Tra nslation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-29 Matrix>Router(config-slb-real)#inser vice Matrix>Rout.
Configuring Load Sharing Network Address Tran slation (LSNAT) show ip slb stats 19-30 LSNAT C onfiguration 1 192.169.1.11 192.168.1.253 23 1249 TCP OUT-SERVR REPLY This example shows how .
show ip slb sticky Configuring Load Shar ing Network Address Tra nslation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-31 Parameters None.
Configuring Load Sharing Network Addres s Tran slation (LSNAT) c lear ip slb 19-32 LSNAT C onfiguration clear ip slb Use this command to clear server load balancing counters or to remove serv er load balancing connections.
set router limits (LSNAT) Configuring Load S haring Network Address Translation (LSNAT ) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-33 Usage This command must be executed from the switch CLI.
Configuring Load Sharing Network Address Tran slation (LSNAT) clear router limits (LSNAT) 19-34 LSNAT C onfiguration Default s •I f not specified, maximum bindings wi ll be set to the default va l u e of 5000.
clear router limits (LSNAT) Configuring Load Sharing Network Address Tra nslation (LSNAT) Enterasys Matrix DFE-Gold Series Configur ation Guide 19-35 Mode Switch command, Read ‐ Wr i t e . Usage This command must be executed from the switch CLI.
Configuring Load Sharing Network Address Tran slation (LSNAT) clear router limits (LSNAT) 19-36 LSNAT C onfiguration.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 20-1 20 DHCP Configuration This chapter descri bes the Dynamic Host Configuration Protocol (D HCP) configuration set of commands and how to us e them.
DHCP Overview 20-2 DHCP C onfiguration To configure DHCP on the Enterasys Matr ix ‐ N or standalone device, you must configure an IP address pool, client parameters, and optional stati c IP address for a specifie d scope.
DHCP Overview Enterasys Matrix DFE-Gold Series Configuratio n Guide 20-3 Domain Name 15 Swap Server 16 Root Path 17 Extensions Path 18 IP Forwarding Enable/D isable 19 Non Local Source Routing Enabl e.
DHCP Overview 20-4 DHCP C onfiguration DHCP Command Modes Except for clear and sh ow commands, most DHCP configuration commands can be executed in most of the DHCP command modes shown in Ta b l e 2 0 ‐ 2 .
DHCP Overview Enterasys Matrix DFE-Gold Series Configuratio n Guide 20-5 Commands DHCP Class Configuration Mode Configure a DHCP client class. Ty p e client-class and the client class name from DHCP Pool or Host Configuration Mode. Matrix>Router (config-dhcp-class)# DHCP Host Configuration Mode Configure DHCP host parameters.
DHCP Overview ip dhcp server 20-6 DHCP C onfiguration ip dhcp server Use this command to enable DHCP server features on a routing interface. Synt ax ip dhcp server no ip dhcp Parameters None. Default s None.
exclude DHCP Overview Enterasys Matrix DFE-Gold Series Configuratio n Guide 20-7 Default s None. Mode Router command, Glob al configuration: Matrix >Router(config)# Usage The “no” form of this command removes the local addr ess pool.
DHCP Overview ip dhcp ping packets 20-8 DHCP C onfiguration ip dhcp ping p acket s Use this command to specify the number of packets a DHCP server sends to an IP addres s before assigning the address to a requesting client.
ip dhcp pool DHCP Overview Enterasys Matrix DFE-Gold Series Configuratio n Guide 20-9 Usage The “no” form of this command resets the ping timeout to the default val u e .
DHCP Overview dns-server 20-10 DHCP C onfiguration Parameters Default s None. Mode Router command, Any DHCP configuration mod e. Usage This command configures DHCP option 15. The “no” form of this command deletes a DHCP domain name.
netbios-name-server DHCP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-11 Example This example shows how to assign a DNS server at 11.
DHCP Overview default-router 20-12 DHCP C onfiguration Parameters Default s None. Mode Router command, Any DHCP configuration mod e. Usage This command configures DHCP option 46. The “no” form of this command deletes the NetBIOS node type.
bootfile DHCP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-13 Usage This command configures DHCP option 3. The ʺ no ʺ form of this command deletes the default router list.
DHCP Overview option 20-14 DHCP C onfiguration Parameters Default s None. Mode Router command, Any DHCP configuration mod e. Usage The next se rver is the serv .
lease DHCP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-15 Usage These configuratio n parameters and other control information are carried in .
DHCP Overview host 20-16 DHCP C onfiguration Usage The “no” form of this command resets the lease duration to the default va l u e of 1 day (24 hours).
client-identifier DHCP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-17 Parameters Default s None. Mode Router command, Any DHCP configuration mod e.
DHCP Overview client-name 20-18 DHCP C onfiguration Example This example shows how to assign client MAC address 00.01f4.0127 within “clientclass1”: Matrix>Router(config)#ip dhcp pool l ocalpool Matrix>Router(config-dhcp-pool)#clie nt-identifier 0100.
show ip dhcp binding DH CP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-19 Parameters Default s If type is not specified, Ethernet will be applied. Mode Router command, Any DHCP configuration mod e .
DHCP Overview clear ip dhcp binding 20-20 DHCP C onfiguration Example This example shows how to display the DHCP binding address parameters, including a.
show ip dhcp ser ver statistics DHCP Overview Enterasys Matrix DFE-Gold Series Configur ation Guide 20-21 Mode Router command, Any DHCP configuration mod e.
DHCP Overview clear ip dhcp server statistics 20-22 DHCP C onfiguration clear ip dhcp server st atistics Use this command to reset all DHCP server counters. Synt ax clear ip dhcp server statistics Parameters None. Default s None.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 21-1 21 Routing Protocol Configuration This chapter describes the Routing Protocol Configuration set of command s and how to use the m.
Configuring RIP router rip 21-2 Routing Proto col Configuration router rip Use this command to enable or disable RIP configuration mode. Synt ax router rip no router rip T able 21- 1 RIP Configuration T ask List and Commands T o do this.
network Configuring RIP Enterasys Matrix DFE-Gold Series Configuratio n Guide 21-3 Parameters None. Default s None. Mode Router command, Glob al configuration: Matrix>Ro uter(config.
Configuring RIP neighbor 21-4 Routing Proto col Configuration Example This example shows how to attach network 192.168.1.0 to the RIP routing process: Matrix>Router(config)#router rip Matrix>Router(config-router)#network 192.
ip ri p offs et Configuring RIP Enterasys Matrix DFE-Gold Series Configuratio n Guide 21-5 Parameters Default s None. Mode Router command, Router configuration: Matrix>Rout er(confi.
Configuring RIP timers 21-6 Routing Proto col Configuration Default s None. Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage Adding an offset on an interface is used for the purpose of making an interface a backup.
ip rip send ver sion Configuring RIP Enterasys Matrix DFE-Gold Series Configuratio n Guide 21-7 Example This example shows ho w to set RIP timers to a 5 sec.
Configuring RIP key chain 21-8 Routing Proto col Configuration Parameters Default s None. Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Us.
key Configuring RIP Enterasys Matrix DFE-Gold Series Configuratio n Guide 21-9 Example This example shows how to create a RIP authentication key chain calle.
Configuring RIP accept-lifetime 21-10 Routing Prot ocol Configuration Parameters Default s None. Mode Router command, Key chain key config uration: Matrix>Router(config-keychain-key)# Usage The “no” form of this command removes the authentication string.
send-lifetime Configuring RIP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-11 Default s None. Mode Router command, Key chain key configuration: Matrix >Router(co.
Configuring RIP ip rip authentication keychain 21-12 Routing Prot ocol Configuration Default s None. Mode Router command, Key chain key configuration: Matrix >Router(config .
ip rip authentication mod e Configuring RIP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-13 ip rip authentication mode Use this command to set the authentication mode when a key cha in is present.
Configuring RIP ip rip disa ble-triggered-updates 21-14 Routing Prot ocol Configuration Usage This command is necessary for enabling CIDR for RIP on the Enterasys Matrix Series device.
ip split-horizon poison Configuring RIP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-15 ip split-horizon poison Use this command to enable or disable split horizon poison ‐ reverse mode for RIP packets .
Configuring RIP receive-interface 21-16 Routing Prot ocol Configuration Mode Router command, Router configuration: Matrix>Rout er(config ‐ router)# Usage This command does not prevent RIP from monitoring updates on the interface.
distribute-list Configuring RIP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-17 distribute-list Use this command to filter networks rece ived and to suppress netw orks from being advertised in RIP updates.
Configuring RIP redistribute 21-18 Routing Prot ocol Configuration Parameters Default s •I f metric value is not s pecified, 1 wil l be applied. •I f subnets is not specified, only non ‐ subnetted routes will be redistributed.
redistribute Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-19 Configuring OSPF Underst anding Graceful Rest art OSPF gracef ul restart, sometimes referred .
Configuring OSPF redistribute 21-20 Routing Prot ocol Configuration own forw arding engine that uses this information to make forw arding decisions locally on the module that receives the frame.
redistribute Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-21 OSPF Configuration T ask List and Commands Ta b l e 2 1 ‐ 2 list s the tasks and commands associated with OSPF configuration.
Configuring OSPF router ospf 21-22 Routing Prot ocol Configuration router osp f Use this command to enable or disable Open Shortest Pa t h First (OSPF) configuration mode. Synt ax router ospf process-id no router ospf process-id Parameters Default s None.
network Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-23 Mode Router command, Glob al configuration: Matrix>Ro uter(config)# Usage Yo u must exec.
Configuring OSPF router id 21-24 Routing Prot ocol Configuration Example This example shows how to configure IP address 182.127.62.1 0.0.0.31 as OSPF area 0: Matrix>Router(config)#router ospf 1 Matrix>Router(config-router)#network 182.
ip ospf priority Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-25 Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage Each router interface that participates in OSPF routing is assigned a default cost.
Configuring OSPF timers spf 21-26 Routing Prot ocol Configuration timers sp f Use this command to change OSPF timer va l u e s to fine ‐ tune the OSPF network. Synt ax timers spf spf-delay spf-hold no timers spf Parameters Default s None.
ip ospf transmit-delay Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-27 Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan .
Configuring OSPF ip ospf hello- interval 21-28 Routing Prot ocol Configuration ip osp f hello-interval Use this command to set the number of seconds a router must wai t before sending a hello packet to neighbor routers on an interface.
ip ospf authentication-key Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-29 Default s None. Mode Router command, Interface configuration: Matrix> Router(.
Configuring OSPF ip ospf message digest key md5 21-30 Routing Prot ocol Configuration Example This example shows how to enables an OSPF au thentication key on .
area range Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-31 Parameters Default s If route type is not specified, the distance va l u e will be applied to all OSPF routes (110).
Configuring OSPF area authentication 21-32 Routing Prot ocol Configuration Parameters Default s None. Mode Router command, Router configuration: Matrix>Rout er(config ‐ router)# U.
area stub Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-33 Usage The “no” form of this command disables authentication for an OSPF area. Example This example shows how to enable MD5 auth entication on OSPF area 10.
Configuring OSPF area default cost 21-34 Routing Prot ocol Configuration area default cost Use this command to set the cost val u e for the default route that is sent into a stub area by an Area Border Router (ABR).
area virtual-link Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-35 Default s If default ‐ information ‐ originate is not specif ied, no default type will be generated.
Configuring OSPF passive-interface 21-36 Routing Prot ocol Configuration Default s None. Mode Router command, Router configuration: Matrix>Rout er(config ‐ router)# Usage The “no” form of this command removes the virtual link.
redistribute Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-37 Mode Router command, Router configuration: Matrix ‐ >Rou ter(config ‐ router)# Usag.
Configuring OSPF database-overflow 21-38 Routing Prot ocol Configuration Default s •I f metric value is not s pecified, 0 wil l be applied. •I f type value is not specif ied, type 2 (external route) will be applied.
graceful-restart enable Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-39 Mode Router command, Router configuration: Matrix ‐ >Rou ter(config ‐ router.
Configuring OSPF graceful-restart helper-disable 21-40 Routing Prot ocol Configuration Example This example shows how to enable the graceful restart ability on .
graceful-restart stri ct-lsa-checking-disable Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-41 Parameters Default s None. Mode Router command, Router configurat.
Configuring OSPF show ip ospf 21-42 Routing Prot ocol Configuration Example This example shows how to disable strict LSA checking on thi s router: Matrix-&g.
show ip ospf database Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-43 Link State Update Interval is 00 :30:00 and due in 00:02:28. Link State Age Interval is 00:00 :00 and due in 00:00:00. Area 0.0.0.2 Number of interfaces in this are a is 3 Area has no authentication SPF algorithm executed 61 times Area ranges are 140.
Configuring OSPF show ip ospf database 21-44 Routing Prot ocol Configuration Default s If link ‐ state ‐ id is not specified, the specified type of database rec ords will be display ed for all link state IDs.
show ip ospf border -routers Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-45 show ip osp f border-routers Use this command to display information a.
Configuring OSPF show ip ospf interface 21-46 Routing Prot ocol Configuration Parameters Default s If vlan ‐ id is not specified, OSPF statistics will be display ed for all VLANs. Mode Router command, Any router mode.
show ip ospf neighb or Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-47 show ip osp f neighbor Use this command to display the state of communication betw een an OSPF router and its neighbor routers.
Configuring OSPF show ip ospf virtual-links 21-48 Routing Prot ocol Configuration Example This example shows how to use the show ospf neighbor comm and: Matrix>Router#show ip ospf neighbor ID Pri State Dead-Int Address Interface 182.
clear ip ospf process Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-49 Hello 10, Dead 40, W ait 40, Retransmit 5 Adjacency State FULL Ta b l e 2 1 ‐ 6 provides an explanation of the command output.
Configuring OSPF debug ip ospf 21-50 Routing Prot ocol Configuration debug ip osp f Use this command to enable OSPF protocol debuggi ng output. Synt ax debug ip ospf { subsystem } no debug ip ospf { subsystem } Parameters Default s None.
rfc1583compatible Configuring OSPF Enterasys Matrix DFE-Gold Series Configur ation Guide 21-51 Mode Router command, Router configuration: Matrix>Rout er(config ‐ router)# Usage The “no” form of this command removes OSPF RFC 1583 compatible.
Configuring DVMRP ip dvmrp 21-52 Routing Prot ocol Configuration Configuring DVMRP Purpose To enable and configure the Distance Ve c t o r Multicast Routing Protocol (DVMRP) on an interface.
ip dvmrp metric Configuring DVMRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-53 The “no” form of this command disables DVMRP .
Configuring DVMRP show ip dvmrp route 21-54 Routing Prot ocol Configuration Mode Router command, Any router mode. Example This example shows how to display DVMRP routing table entries. In this case, the routing table has 5 entries.
ip irdp Configuring IRDP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-55 Configuring IRDP Purpose To enable and configure the ICMP Router Discovery Protocol (IRDP) on an interface.
Configuring IRDP ip irdp maxadvertinterval 21-56 Routing Prot ocol Configuration ip ird p maxadvertinterval Use this command to set the maximum interv al in seconds between IRDP ad vertise ments. Synt ax ip irdp maxadvertinterval interval no irdp maxadvertinterval Parameters Default s None.
ip irdp holdtime Configurin g IRDP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-57 Usage The “no” form of this command deletes the custom holdtime .
Configuring IRDP ip irdp preference 21-58 Routing Prot ocol Configuration ip ird p preference Use this command to set the IRDP preference val u e for an interface.
no ip irdp multicast Configuring IRDP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-59 Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage The “no” form of this command clears an IP address from being adv ertised.
Configuring IRDP show ip irdp 21-60 Routing Prot ocol Configuration Default s If vlan vlan ‐ id is not specified, IRDP information for all interfaces will be displayed.
router vrrp Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-61 Configuring VRRP Purpose To enable and configure the Vi r t u a l Router Redundancy Protocol (VRRP).
Configuring VRRP create 21-62 Routing Prot ocol Configuration Usage Yo u must execute the router vrrp command to enable the protocol before completing other VRRP ‐ specific configuration tasks.
address Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-63 address Use this command to configure a virtual router IP address. Synt ax address vlan vlan-id vrid ip-address owner no address vlan vlan-id vrid ip-address owner Parameters Default s None.
Configuring VRRP priority 21-64 Routing Prot ocol Configuration Examples This example shows how to configure a virtual router add ress of 182.
master-icmp-reply Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-65 Example This example shows how set a VRRP priorit y of 200 on .
Configuring VRRP advertise-interval 21-66 Routing Prot ocol Configuration advertise-interval Use this command to set the interv al in seconds between VRRP advertisements. Synt ax advertise-interval vlan vlan-id vrid interval no advertise-interval vlan vlan-id vrid interval Parameters Default s None.
preempt Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-67 Parameters Default s If not specified, critical ‐ priority will be set to 10.
Configuring VRRP preempt-delay 21-68 Routing Prot ocol Configuration Default s None. Mode Router command, Router configuration: Matrix>Rout er(config ‐ router)# Usage The rout.
enable Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-69 When preempt mode is enabled this specifies a delay (in seconds) that a higher priority backup router must wai t to preempt a lower priority master .
Configuring VRRP ip vrrp authentication-key 21-70 Routing Prot ocol Configuration ip vrrp authentication-key Use this command to set a VRRP authentication passw ord on an interface. Synt ax ip vrrp authentication-key password no ip vrrp authentication-key Parameters Default s None.
show ip vrrp Configuring VRRP Enterasys Matrix DFE-Gold Series Configur ation Guide 21-71 Default s None. Mode Router command, Interface configuration: Matrix> Router(config ‐ if(Vlan 1))# Usage The “no” form of this command clears VRRP MD5 authentication.
Configuring VRRP show ip vrrp 21-72 Routing Prot ocol Configuration T able 21-7 show ip vrrp Output Details Output... W hat it displays... Vlan S p ecifies the VLAN on which this VRRP session resides. V rid S pecifies the Virtual Router ID associated with the routing interface.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 22-1 22 Port Priority and Rate Limiting Configuration This chapter describes the Po r t Priority and Rate Limiting set of commands and how to use them.
Configuring Port Priority show port priority 22-2 Port Priority and Rat e Limiting Configuration Configuring Port Priority Purpose To view or configure port priority characteri.
set port priority Configuring Port Priority Enterasys Matrix DFE-Gold Series Configuratio n Guide 22-3 fe.2.5 is set to 0 set port priority Use this command to set the 802.1D (802.1p) Class ‐ of ‐ Service transmit queue priority (0 through 7) on each port.
Configuring Port Priority clear port priority 22-4 Port Priority and Rat e Limiting Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
show port priority-queue Configuring Priority to Transmit Queue Mapping Enterasys Matrix DFE-Gold Series Configuratio n Guide 22-5 Configuring Priority to T ransmit Queue Mapping Purpose To perfor.
Configuring Priority to Transmit Queue Mapping set port p riority-queue 22-6 Port Priority and Rat e Limiting Configuration Examples This example shows how to display priority queue information for fe.
clear port priority-queue Configuring Priority to Transmit Queue Mapping Enterasys Matrix DFE-Gold Series Configuratio n Guide 22-7 Parameters Default s None.
Configuring Priority to Transmit Queue Mapping clear port priority-queue 22-8 Port Priority and Rat e Limiting Configuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear the priority queue settings on fe.
show port ratelimit Configuring Port Traffic Rate Limiting Enterasys Matrix DFE-Gold Series Configuratio n Guide 22-9 Configuring Port T raffic Rate Limiting Purpose To limit the rate of inbound tra ffic on the Enterasys Matrix Series devi ce on a per port/priority basis.
Configuring Port Traffic Rate Limiting set port ratelimit 22-10 Port Prior ity and Rate Limiting Configuration ----------- ----- --------- ----- ------- --------- ----------- -------- fe.2.1 1 64125 discard inbound 0 disabled fe.2.1 2 64125 discard inbound 0 disabled fe.
clear port ratelimit C onfiguring Port Traffic Rate Limiting Enterasys Matrix DFE-Gold Series Configur ation Guide 22-11 Default s •I f not specified, threshold will be applied to inbound traffic on the port/priority .
Configuring Port Traffic Rate Limiting clear port ratelimit 22-12 Port Prior ity and Rate Limiting Configuration Example This example shows how to clear all rate limiting para meters on port fe.2.: 1Matrix(rw)->clear port ratelimit fe .
Enterasys Matrix DFE-Gold Series Configuratio n Guide 23-1 23 T ransparent W eb Cache Balancing Configuration This chapter descri bes the T ransparent We b Cache Balancing (TWCB) commands and how to use them.
Understanding Transparent Web Cache Balancing (TWCB) 23-2 Transpa rent Web Cache Balancing Configuration farm is configured with 2 cache servers from the 186. 89.0.0 subnet. The s2Server serv er farm is configured with 5 cache servers from the 176.
ip twcb wcserverfarm Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configuratio n Guide 23-3 ip twcb wcserverfarm Use this command to create a we b ‐ cache server farm. Synt ax ip twcb wcserverfarm serverfarm-name Parameters Default s None.
Understanding Transparent Web Cache Balancing (TWCB) predictor roundrobin 23-4 Transpa rent Web Cache Balancing Configuration predictor roundrobin Use this command to modify the .
cache Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configuratio n Guide 23-5 cache Use this command to create a cache server based upon the supplied IP addre ss.
Understanding Transparent Web Cache Balancing (TWCB) faildetect 23-6 Transpa rent Web Cache Balancing Configuration Mode Router command, Cach e Serve r Configuration mode: Mat rix(rw) ‐ >Router(config ‐ twcb ‐ cache)# .
maxconns Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configuratio n Guide 23-7 maxconns Use this command to limit the maximum number of connections to the serv er .
Understanding Transparent Web Cache Balancing (TWCB) ip twcb webcache 23-8 Transpa rent Web Cache Balancing Configuration Examples This example sets the maximum number of connections for cache serv er 186.89.
http-port Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configuratio n Guide 23-9 http-port Use this command to redirect outbound HTTP requests to a non ‐ standard HTTP port number .
Understanding Transparent Web Cache Balancing (TWCB) bypass-list range 23-10 Tr ansparent Web Cache Balancin g Configuration Example This example adds the server farm s1Server .
ip twcb redirect out Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configur ation Guide 23-11 Parameters Default s None. Mode Router command, Cach e Serve r Configuration mode: Mat rix(rw) ‐ >Router(config ‐ twcb ‐ webcache)# .
Understanding Transparent Web Cache Balanc ing ( TWCB) show ip twcb wcserverfarm 23-12 Tr ansparent Web Cache Balancin g Configuration Example This example associates the cache1 we.
show ip twcb webcache Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configur ation Guide 23-13 show ip twcb webcache Use this command to display configuration data associated with the specified web ‐ cache.
Understanding Transparent Web Cache Balancing (TWCB) show ip twcb stats 23-14 Tr ansparent Web Cache Balancin g Configuration Example This example displays connection data for .
show limits Understanding Transparent Web Cache Balancing (TWCB) Enterasys Matrix DFE-Gold Series Configur ation Guide 23-15 Default s If no parameter is specified, statistics for all we b ‐ caches, server farms, and cache serv ers are cleared.
Understanding Transparent Web Cache Balancing ( TWCB) show router limits (TWCB) 23-16 Tr ansparent Web Cache Balancin g Configuration Parameters Default s None.
clear router limits (TWCB) Understanding Transparent Web Cache Balan cing (TWCB) Enterasys Matrix DFE-Gold Series Configur ation Guide 23-17 Mode Switch command mode: Matrix(rw) ‐ > .
Understanding Transparent Web Cache Balanc ing ( TWCB) clear router limits (TWCB) 23-18 Tr ansparent Web Cache Balancin g Configuration Usage This command must be executed from the switch CLI.
clear router limits (TWCB) TWCB Con figuration Example Enterasys Matrix DFE-Gold Series Configur ation Guide 23-19 TWCB Configuration Example In this TWCB configuration example we will step through the configuration of two serve r farms named s1Server and s2Server .
TWCB Configuration Example clear router limits (TWCB) 23-20 Tr ansparent Web Cache Balancin g Configuration Matrix>router Matrix>Router>enable Matrix>Router>#configure Enter configurati.
clear router limits (TWCB) TWCB Con figuration Example Enterasys Matrix DFE-Gold Series Configur ation Guide 23-21 Matrix>Router(config-twcb-wcsfarm)#e xit Matrix>Router(config)# Configure the c.
TWCB Configuration Example clear router limits (TWCB) 23-22 Tr ansparent Web Cache Balancin g Configuration.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 24-1 24 Security Configuration This chapter descri bes the Security Configurat ion set of commands and how to use them.
Configuring MAC Locking show maclock 24-2 Secur ity Configuration •F l o w Setup Throttling (FST) — prevents the effects of DoS attacks by limiting .
show maclock Configuring MAC Locking Enterasys Matrix DFE-Gold Series Configuratio n Guide 24-3 Parameters Default s If port_string is not specified, MAC locking status will be displayed for all ports.
Configuring MAC Locking show maclock stations 24-4 Secur ity Configuration show maclock st ations Use this command to display MAC locking information about end stations connected to the device.
set maclock enable Configu ring MAC Locking Enterasys Matrix DFE-Gold Series Configuratio n Guide 24-5 set maclock enable Use this command to enable MAC locking on one or more por ts.
Configuring MAC Locking set ma clock 24-6 Secur ity Configuration Parameters Default s If port_string is not specified, MAC locking will be disabled on all ports. Mode Switch command, Read ‐ Wr i t e .
set maclock firs tarrival Configuring MAC Locking Enterasys Matrix DFE-Gold Series Configuratio n Guide 24-7 Example This example shows how to create a MAC locking association between MAC addr ess 00 ‐ a0 ‐ c9 ‐ 0d ‐ 32 ‐ 11 and port fe.
Configuring MAC Locking clear maclock firstarrival 24-8 Secur ity Configuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to move all current first arrival MA Cs to static entries on fe.
clear maclock static Configuring MAC Locking Enterasys Matrix DFE-Gold Series Configuratio n Guide 24-9 Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to restrict MAC locking to 4 static addresses on fe.
Configuring MAC Locking clear maclock 24-10 Secu rity Configuration Default s None. Mode Switch command, Read ‐ Wr i t e . Usage When enabled, this authorizes the device .
show ssh state Configuring Secure Shell (SSH) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-11 Configuring Secure Shell (SSH) Purpose To review , enable, disable, and configure the Secure Shell (SSH) protocol, which provides secure Te l n e t .
Configuring Secure Shell (SSH) set ssh hostkey 24-12 Secu rity Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set router ssh Configuring Secu re Shell (SSH) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-13 Default s None. Mode Switch command, Read ‐ Only .
Configuring Secure Shell (SSH) clear router ssh 24-14 Secu rity Configuration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to reset SSH s.
show access-lists Con figuring Access Lists Enterasys Matrix DFE-Gold Series Configur ation Guide 24-15 Configuring Access List s Purpose To review and configure security access .
Configuring Access Lists access-list (standard) 24-16 Secu rity Configuration deny ip 150.136.0.0 0.0.255.255 224. 0.0.0 15.255.255.255 deny ip 11.6.0.
access-list (extended) Configuring Access Lists Enterasys Matrix DFE-Gold Series Configur ation Guide 24-17 Default s •I f insert, replace or move are not specifie d, the new entry will be appended to the access list.
Configuring Access Lists access-list (extended) 24-18 Secu rity Configuration T o apply ACL restrictions to IP , UDP , or ICMP p acket s: access-list access-list-number { deny | permit } protocol sour.
access-list (extended) Configuring Access Lists Enterasys Matrix DFE-Gold Series Configur ation Guide 24-19 Default s •I f insert , replace , or move are not specif ied, the new entry will be appended to the access list.
Configuring Access Lists ip access-group 24-20 Secu rity Configuration Mode Router command, Glob al configuration: Matrix>Ro uter(config)# Usage Va l i d access ‐ list ‐ numbers for extended ACLs are 100 to 199 .
ip access-group Configuring Access Lists Enterasys Matrix DFE-Gold Series Configur ation Guide 24-21 Usage ACLs must be applied per routing interface. An entry (rule) can either be applied to inbound or outbound frames.
Configuring Denial of Service (DoS) Prevention show hostdos 24-22 Secu rity Configuration Configuring Denial of Service (DoS) Prevention Purpose To configure Denial of Service (DoS) prev ention, which wi ll protect the router from attacks and notify administrator s via Syslog.
hostdos Configuring Denial of Service (D oS) Prevention Enterasys Matrix DFE-Gold Series Configur ation Guide 24-23 Disabled IP packet with multicast/broadcast s ource address Always enabled 0 attacks.
Configuring Denial of Service (DoS) Prevention clear hostdos-counters 24-24 Secu rity Configuration Examples This example shows how to globally enable land attack a.
clear hostdos-counters Configur ing Flow Setup Throttling (FST) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-25 Configuring Flow Setup Throttling (FST) About FST Flow Setup Throttl.
Configuring Flow Setup Throttling (FST) show flowlimit 24-26 Secu rity Configuration show flowlimit Use this command to display flow setup throttling information.
set flowlimit limit Configuring Flow Setup Throttling (FST) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-27 Example This example shows how to enable FST on Fast Ethernet ports 1 ‐ 5 in modul e 2: Matrix(rw)->set flowlimit fe.
Configuring Flow Setup Throttling (FST) clear flowlimit limit 24-28 Secu rity Configuration clear flowlimit limit Use this command to remove a flow limit configuration.
clear flowlimit action Configur ing Flow Setup Throttling (FST) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-29 Default s •I f action is not specified, no action will be applied. •I f classification port type is not specif ied, none will be applied.
Configuring Flow Setup Throttling (FST) show flowlimit class 24-30 Secu rity Configuration Default s •I f not specified, all action types will be removed. •I f not specified, the act ion will be removed from all port classifications.
set flowlimit port Configuring Flow Setup Throttling (FST) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-31 Example This example shows how to show flow limits .
Configuring Flow Setup Throttling (FST) clear flowlimit port class 24-32 Secu rity Configuration Default s If port ‐ string is not specif ied, settings will apply to all ports. Mode Switch command, Read ‐ Wr i t e .
set flowlimit notification Configuring Flow Setup T hrottling (FST) Enterasys Matrix DFE-Gold Series Configur ation Guide 24-33 Parameters Default s None.
Configuring Flow Setup Throttling (FST ) clear flowlimit notification inter val 24-34 Secu rity Configuration clear flowlimit notification interval Use this command to reset the SNMP flow limit notificati on interval to the default val u e of 120 seconds.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 25-1 25 Authentication Configuration This chapter descri bes the set of commands for supported authentication methods.
Configuring 802.1X Authentication 25-2 Authentication Co nfiguration •L o c a l user credentials — used for local authentication and authorization of CLI and We b V i e w management sessions.
show dot1x Configuring 802.1X Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 25-3 selected ports, which results in allowing or denying network access according to RADIUS se rver configuration.
Configuring 802.1X Authentication show dot1x 25-4 Authentication Co nfiguration Mode Switch command, Read ‐ Only . Examples This example shows how to display 802.1X status: Matrix(rw)->show dot1x DOT1X is disabled.
show dot1x auth-config Configuring 802.1X Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 25-5 Matrix(rw)->show dot1x auth-stats fe .
Configuring 802.1X Authentication show dot1x auth-config 25-6 Authentication Co nfiguration Default s •I f no parameters are specif ied, all 802.1X settings will be displ ayed. •I f port ‐ string is not specif ied, information for all ports will be displayed.
set dot1x Configuring 802.1X Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 25-7 set dot1x Use this command to ena ble or disable 802.
Configuring 802.1X Authentication set dot1x auth-config 25-8 Authentication Co nfiguration Parameters Default s If port ‐ string is not specif ied, authentication parameters will be set on all por ts Mode Switch command, Read ‐ Wr i t e .
clear dot1x auth-config Configuring 802.1X Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 25-9 This example shows how to enable reauthenti cation control on ports fe.1.1 ‐ 3: Matrix(rw)->set dot1x auth-config re athenabled true fe.
Configuring 802.1X Authentication clear dot1x auth-config 25-10 Authenticat ion Configuration Matrix(rw)->clear dot1x auth-config quietperiod fe.1.1-3.
clear dot1x auth-config Configurin g Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-11 Configuring Port W eb Authentication (PW A) About PW A PW A provides a wa y of authenticating users before allowing general access to the netw ork.
Configuring Port Web Authentication (PWA) clear dot1x auth-config 25-12 Authenticat ion Configuration •a l l o w access to a server (at IP 1.
show pwa Configuring Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-13 show pwa Use this command to display port web authentication information for one or more ports.
Configuring Port Web Authentication (PWA) show pwa 25-14 Authenticat ion Configuration T able 25-1 show pwa Output Det ails Output... W hat it displays... PW A S tatus Whether or not port we b authentica tion is enabled or disabled. Default state of disabled can be changed using the set pwa command a s described in “ set pwa ” on page 25-15.
set pwa Configuring Port Web Authen tication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-15 set pwa Use this command to enable or disable port web authentication. Synt ax set pwa { enable | disable } Parameters Default s None.
Configuring Port Web Authentication (PWA) clear p wa hostname 25-16 Authenticat ion Configuration Example This example shows how to set the PW A host name to .
set pwa banner Configuring Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-17 set pwa banner Use this command to configure a string to be displayed as the PW A login banner .
Configuring Port Web Authentication (PWA) set pwa displaylogo 25-18 Authenticat ion Configuration Parameters None. Default s None. Mode Switch command, Read ‐ Wr i t e .
set pwa ipaddress Configuring Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-19 Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring Port Web Authentication (PWA) set pwa enhancedmode 25-20 Authenticat ion Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set pwa guestname Configurin g Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-21 set pwa guestname Use this command to set a guest user name for PW A enhanced mode networking.
Configuring Port Web Authentication (PWA) set pwa guestpassword 25-22 Authenticat ion Configuration set pwa guestp assword Use this command to set the guest user password for PW A netw orking. Synt ax set pwa guestpassword Parameters None.
set pwa initialize Configuring Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-23 Usage When enhanced mode is enabled (as described i.
Configuring Port Web Authentication (PWA) set pwa maxrequests 25-24 Authenticat ion Configuration Default s If port ‐ string is not specif ied, quiet period will be set for all ports. Mode Read ‐ Wr i t e .
show pwa session C onfiguring Port Web Authentication (PWA) Enterasys Matrix DFE-Gold Series Configur ation Guide 25-25 Parameters Default s Enables or disables all ports if no port is specified. Mode Switch command, Read ‐ Wr i t e .
Configuring MAC Authentication show macauthentication 25-26 Authenticat ion Configuration Configuring MAC Authentication Purpose To review , disable, enab le and configure MAC authentication.
show macauthentication Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-27 Parameters Default s If port ‐ string is not specif ied, MAC authentication information will be display ed for all ports.
Configuring MAC Authentication show macauthentication session 25-28 Authenticat ion Configuration show macauthentication session Use this command to display the active MAC authe nticated sessi ons. Synt ax show macauthentication session Parameters None.
set macauthentication Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-29 set macauthentication Use this command to globally enable or disable MAC authentica tion. Synt ax set macauthentication { enable | disa ble } Parameters Default s Disabled.
Configuring MAC Authentication clear macauthentication passw ord 25-30 Authenticat ion Configuration Default s None. Mode Switch command, Read ‐ Wr i t e .
clear macauthentication significant- bits Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-31 Mode Switch command, Read ‐ Wr i t e .
Configuring MAC Authentication set macauthentica tion authallocated 25-32 Authenticat ion Configuration Usage Enabling port(s) for MAC authentication requires globally enab.
set macauthentication portinitialize Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-33 Default s If port ‐ string is not specif ied the number of allow ed authentication sessions will be cleared on all ports.
Configuring MAC Authentication set macauthe ntication reauthentication 25-34 Authenticat ion Configuration Default s None. Mode Switch command, Read ‐ Wr i t e .
set macauthentication macreauthenticate Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-35 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Example This example shows how to force ge.
Configuring MAC Authentication clear macauthentication reauthperiod 25-36 Authenticat ion Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set macauthentication quietperiod Configuring MAC Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 25-37 set macauthentication quietperiod Use this command to enable a reauthenti cation attempt for failed entries at the period specified in seconds.
Configuring MAC Authentication clear macauthentication quietperiod 25-38 Authenticat ion Configuration Usage The default val ue is 0 (never). Example This example shows how to clear the macauthentication quietperiod for port ge.
clear macauthentication quietperiod Configuring C onvergence End Points (CEP) Phone De tection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-39 Configuring Convergence End Point s (CEP) Pho.
Configuring Convergence End Points (C EP) Phone Detection show cep connections 25-40 Authenticat ion Configuration show cep connections Use this command to display all lear ned CEPs. Synt ax show cep connections port-string Parameters Default s None Mode Read ‐ Only .
show cep policy Configuring Convergence End Points (CEP) Phone De tection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-41 Parameters Default s If no detection ‐ id is specified, al l CEP detection parameters are displayed.
Configuring Convergence End Points (CEP) Phone D etection show cep port 25-42 Authenticat ion Configuration Examples This example shows how to display CEP policy inform.
set cep port Configuring Convergence End Points (CEP) Phone Detection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-43 Default s Disabled. Mode Switch command, Read ‐ Wr i t e .
Configuring Convergence End Points (C EP) Phone Detection set cep detection-id 25-44 Authenticat ion Configuration Parameters Default s None. Mode Switch command, Read ‐ Wr i t e .
set cep detection-id type Configuring Convergence End Points (CEP) Phone Detection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-45 Usage This command applies only to Siemens, H.323, and SIP phone detection.
Configuring Convergence End Points (CEP) Phone D etection set cep detection-id address 25-46 Authenticat ion Configuration set cep detection-id address Use this command to set an H.323, Siemens, or SIP phone detection group’ s IP address or mask.
set cep detection-id porthigh | portlow Configuring Convergence End Points (CEP) Phone De tection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-47 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Usage This command applies only to Siemens, H.
Configuring Convergence End Points (CEP) Phone D etection set cep initialize 25-48 Authenticat ion Configuration Mode Switch command, Read ‐ Wr i t e . Usage This command applies only to Siemens, H.323, and SIP phone detection.
clear cep Configuring Convergence End Points (CEP) Phone De tection Enterasys Matrix DFE-Gold Series Configur ation Guide 25-49 clear cep Use this command to clear convergence end points parameters.
RADIUS Filter-ID Attribute and Dynam ic Policy Profile Assignment clear cep 25-50 Authenticat ion Configuration RADIUS Filter-ID Attribute and Dynamic Policy Profile Assignment If you configur.
show authentication login Setting the Authentication Login Method Enterasys Matrix DFE-Gold Series Configur ation Guide 25-51 show authentication login Use this command to display the current authen tication login method.
Setting the Authentication Login Method clear authentication login 25-52 Authenticat ion Configuration Default s None. Mode Switch command, Read ‐ Wr i t e .
show radius Configuring RADIUS Enterasys Matrix DFE-Gold Series Configur ation Guide 25-53 Configuring RADIUS Purpose To perform the following: •R e v i e w the RADIUS client/server configuration on the device.
Configuring RADIUS set radius 25-54 Authenticat ion Configuration Default s If no parameters are specified, all RA DIUS configuration information will be displayed. Mode Switch command, Read ‐ Only .
clear radius Configuring RADIUS Enterasys Matrix DFE-Gold Series Configur ation Guide 25-55 Default s •I f secret ‐ value is not specified, none will be applied. •I f realm is not specified, any authentication wi ll be allowed.
Configuring RADIUS show radius accounting 25-56 Authenticat ion Configuration Parameters Default s •I f index or all is not specified for clearing RADIUS server , all RADIUS serv er settings will be deleted.
set radius accounting Configuring RADIUS Enterasys Matrix DFE-Gold Series Configur ation Guide 25-57 Default s If no parameters are specified, all RA DIUS accounting configuration information will be display ed.
Configuring RADIUS clear radius accounting 25-58 Authenticat ion Configuration Default s None. Mode Switch command, Read ‐ Wr i t e . Examples This example shows how to e.
clear radius accounting Configuring RADIUS Enterasys Matrix DFE-Gold Series Configur ation Guide 25-59 Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring RFC 3580 show vlanauthorization 25-60 Authenticat ion Configuration Configuring RFC 3580 About RFC 3580 RFC 3580 provides suggestions on how 802.1x Authenticators should lev erage RADIUS as the backend AAA infrastructure.
set vlanauthorization Configuring RFC 3580 Enterasys Matrix DFE-Gold Series Configur ation Guide 25-61 Mode Switch command, Read ‐ Only . Example This example shows how to display VLAN Authorization configuration information for ports ge.
Configuring RFC 3580 clear vlanauthorization 25-62 Authenticat ion Configuration Example This example shows how to enable VLAN Authorization: Matrix(su)->set vlanauthorization en able This example shows how to enable VLAN Authorization for port ge.
show tacacs Configuring TACACS+ Enterasys Matrix DFE-Gold Series Configur ation Guide 25-63 Configuring T ACACS+ Purpose To perform the following: •R e v i e w the T ACACS+ client and server configurations on the device.
Configuring TACACS+ show tacacs 25-64 Authenticat ion Configuration Mode Switch command, Read ‐ Only . Example This example shows how to display all T ACACS c.
set tacacs Configu ring TACACS+ Enterasys Matrix DFE-Gold Series Configur ation Guide 25-65 set t a cacs Use this command to enable or disable the T ACACS+ client. Synt ax set tacacs { enable | disable } Parameters Default s None.
Configuring TACACS+ set taca cs server 25-66 Authenticat ion Configuration Example This example displays configuration information for all configured T ACACS+ serv ers. Matrix(ro)->show tacacs server all TACACS+ Server IP Address Po rt Timeout Status -------------- --------------- -- --- ------- ------- 1 192.
clear tacacs serv er Configuring TACACS+ Enterasys Matrix DFE-Gold Series Configur ation Guide 25-67 clear t acacs server Use this command to remove one or all configur.
Configuring TACACS+ set tacacs session 25-68 Authenticat ion Configuration Matrix(ro)->show tacacs session auth orization TACACS+ service: exec TACACS+ session authorization A-V p airs: access leve.
clear tacacs se ssion Configuring TACACS+ Enterasys Matrix DFE-Gold Series Configur ation Guide 25-69 Mode Switch command, Read ‐ Wr i t e . Usage When session accounting is .
Configuring TACACS+ sh ow tacacs command 25-70 Authenticat ion Configuration Default s At least one of the session authorization parameters must be specified.
set tacacs comm and Configuring TACACS+ Enterasys Matrix DFE-Gold Series Configur ation Guide 25-71 set t a cacs command Use this command to enable or disable T ACACS+ accounting or authorization on a per ‐ command basis.
Configuring TACACS+ set tacacs singleconnect 25-72 Authenticat ion Configuration Default s If state is not s pecified, all single connection configuration parameters are displayed (which at this time includes only the enabled/disabled state).
Enterasys Matrix DFE-Gold Series Configuratio n Guide 26-1 26 RADIUS Snooping Configuration This chapter descri bes the RADIUS Snooping commands and how to use them.
Understanding RADIUS Snooper set radius-snooping 26-2 RADIUS Snoop ing Configuration • Globally enable RS on the switch •E n a b l e RS on those ports yo u .
set radius-snooping timeo ut Understanding RADIUS Snoo per Enterasys Matrix DFE-Gold Series Configuratio n Guide 26-3 Parameters Default s None. Mode Read ‐ Wr i t e . Usage This command does not enable RS on the ports for this device.
Understanding RADIUS Snooper set radius-snooping port 26-4 RADIUS Snoop ing Configuration Example This example shows how to set the RS timeout to 30 seconds.
set radius-snooping flow Understanding RADIUS Snooper Enterasys Matrix DFE-Gold Series Configuratio n Guide 26-5 Example This example enables RS on ports ge.
Understanding RADIUS Snooper set radius-snooping initialize 26-6 RADIUS Snoop ing Configuration set radius-snooping initialize Use this command to terminate all RS sessions on the system for the spec ified port or MAC address.
clear radius-snooping flow Understanding RADIUS Snooper Enterasys Matrix DFE-Gold Series Configuratio n Guide 26-7 clear radius-snooping flow Use this command to clear all entries or the specified index entry from the RS flow table.
Understanding RADIUS Snooper show radius-snooping port 26-8 RADIUS Snoop ing Configuration Example This example shows how to display RADIUS configuration information: Matrix(rw)->show radius-snooping RADIUS Snooping: Enabled Number of configured flows: 2 Active sessions: 12 Enabled ports: fe.
show radius-snooping flow Understanding RADIUS Snooper Enterasys Matrix DFE-Gold Series Configuratio n Guide 26-9 show radius-snooping flow Use this command to display information for all flows or the specified index entry in the flow table.
Understanding RADIUS Snooper show radius-snooping session 26-10 RADIUS Snoo ping Configuration Total RADIUS Access Accepts : 212 Total RADIUS Access Rejects : 26 Invalid RADIUS Request packets : 0 Inv.
show radius-snooping session Understanding RADIUS Snooper Enterasys Matrix DFE-Gold Series Configur ation Guide 26-11 Default s None. Mode Read ‐ Only . Examples This example displays RADIUS configuration information for port fe.
Understanding RADIUS Snooper show radius-snooping session 26-12 RADIUS Snoo ping Configuration.
Enterasys Matrix DFE-Gold Series Configuratio n Guide 27-1 27 MultiAuth Configuration This chapter descri bes the MultiA uth set of comman ds and how to use them.
Configuring Multiple Authentication set multiauth mode 27-2 MultiAuth Co nfiguration Commands set multiauth mode Use this command to set the system authentication mode to use multiple authe nticators simultaneously or to strictly adhere to 802.
clear multiauth mode Configuring Multiple Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 27-3 Default s None. Mode Switch command, Read ‐ Wr i t e .
Configuring Multiple Authentication show multiauth counters 27-4 MultiAuth Co nfiguration Example This example shows how to display multiple authentication session ‐ .
set multiauth precedence Configur ing Multiple Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 27-5 lag.0.46 0 0 0 0 lag.0.47 0 0 0 0 lag.0.48 0 0 0 0 set multiauth precedence Use this command to set the system’ s multiple authentica tion administrative precedence .
Configuring Multiple Authentication show multiauth port 27-6 MultiAuth Co nfiguration Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear t.
clear multiauth port Configur ing Multiple Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 27-7 Parameters Default s None. Mode Switch command, Read ‐ Wr i t e . Examples This example shows how to set the port multipl e authentication mode to required on ge.
Configuring Multiple Authentication show multiauth station 27-8 MultiAuth Co nfiguration show multiauth st ation Use this command to display multiple authenticati on station (end user) entries.
show multiauth session Configuring Mu ltiple Authentication Enterasys Matrix DFE-Gold Series Configuratio n Guide 27-9 Mode Switch command, Read ‐ Wr i t e . Example This example shows how to clear the multiple authentication station entry associated with port fe.
Configuring Multiple Authentication show multiauth idle-timeout 27-10 MultiAuth C onfiguration Termination time: Not Terminated show multiauth idle-timeout Use this command to display the multiple authentication timeout va l u e for an idle session.
clear multiauth idle-timeout Configuring Multiple Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 27-11 Default s If no authentica tion method is specified, the timeout va l u e is set for all methods.
Configuring Multiple Authentication show multiauth session-timeout 27-12 MultiAuth C onfiguration Default s If no authentica tion type is specified , the idle timeout va l u e is retur ned to 300 seconds for all authentication types.
set multiauth session-timeout Configuring Multiple Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 27-13 set multiauth session-timeout Use this command to set .
Configuring Multiple Authentication clear multiauth session-timeout 27-14 MultiAuth C onfiguration clear multiauth session-timeout Use this command to clear session ‐ timeout va l u e s , for one or all authenticati on methods, back to the default va lu e s .
clear multiauth trap Configur ing Multiple Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 27-15 Parameters Default s All sending of multiauth traps disabled.
Configuring Multiple Authentication show multiauth trap 27-16 MultiAuth C onfiguration Default s None. Mode Switch command, Read ‐ Wr i t e .
show multiauth trap Configuring Multiple Authentication Enterasys Matrix DFE-Gold Series Configur ation Guide 27-17 Matrix(rw)-> This example shows how to display multiple .
Configuring Multiple Authentication show multiauth trap 27-18 MultiAuth C onfiguration.
Index-1 Index Numerics 802.1D 6-1 802.1Q 7-1 802.1w 6-1 802.1x 25-54 , 25-65 A Access Groups 24-2 0 Access Lists 24-16 to 24-17 Addresses IP, adding to switch routing table 12-8 MAC, adding entri es t.
Index-2 Login administratively configure d 2-8 default 2-7 setting accounts 2-15 via Telnet 2-8 Loop Protect about 6-2 configuring 6-65 Loopback Interfaces 16-1 LSNAT 18-1 , 19-1 M MAC Addresses age t.
Index-3 bridge parameters 6-3 features 6-2 Loop Protect feature 6-2 port parameters 6-49 Rapid Spanning Tree Protocol (RSTP) 6-1 Split Horizon 21- 15 Stub Area s 21-33 Syslog 10-1 System Informati on .
Index-4.
An important point after buying a device Enterasys Enterasys Matrix DFE-Gold Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enterasys Enterasys Matrix DFE-Gold Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enterasys Enterasys Matrix DFE-Gold Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enterasys Enterasys Matrix DFE-Gold Series you will learn all the available features of the product, as well as information on its operation. The information that you get Enterasys Enterasys Matrix DFE-Gold Series will certainly help you make a decision on the purchase.
If you already are a holder of Enterasys Enterasys Matrix DFE-Gold Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enterasys Enterasys Matrix DFE-Gold Series.
However, one of the most important roles played by the user manual is to help in solving problems with Enterasys Enterasys Matrix DFE-Gold Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enterasys Enterasys Matrix DFE-Gold Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
