Instruction/ maintenance manual of the product KF160OI01 Emerson
Go to page of 16
Net Weight: 30.6 Lbs. Part No. F40BP72830004 Form No. BP7283-4 U.L. Model No.: KF160 READ AND SA VE THESE INSTRUCTIONS KF160OI01 Olde Iron with Washed Oak/Honey Maple Blades HIGH COUNTR Y Ceiling Fan .
W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’s manual carefully and keep it for future reference.
3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper One stepladder Six wire connectors (supplied) Three 60-watt (max.) candelabra base bulbs Three 40-watt (max.) cnadelabra base round bulbs Materials Wiring, outlet box and box connectors must be of type required by the local code.
General Y our Emerson ceiling fan comes equipped with a remote control transmitter and a remote control receiver . This remote con- trol systems is designed to control your ceiling fan speed, airflow direction, and light intensity .
2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter .
7. Carefully remove the fan motor housing assembly from the lower foam pad. T urn the housing assembly over and position it on the lower foam pad with the fan blades resting on the pad so that the top of the motor faces up.
tight against the pin and securely tight- en the setscrew in the hanger ball. A loose setscrew could create fan wobble. DOWNROD DECORA TIVE COVER GROMMET DECORA TIVE SCROLL ASSEMBL Y 40-WA TT CANDELABRA BASE ROUND BULB (3) 10. T ighten the setscrews (Figure 6) secure- ly while pulling up on the downrod.
2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 1 1). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 10).
9 1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12. NOTE: Make all wiring connections using wire connectors (supplied).
NOTE: If you wish to operate your ceil- ing fan with the downlight fixture attached, perform steps 7 and 8. Otherwise, skip to step 9. 7. For Operating Y our Fan With the Downlight Fixture.
10. Screw in three 60-watt (maximum) candelabra base bulbs into the light fitter sockets (Figure 18). Remove and retain the nut and rubber washer from the light fitter threaded nipple. Place the lower glass over the threaded nipple and secure in place using the rubber washer and nut.
12 Operating Y our Ceiling Fan IMPORT ANT Fan installation must be completed, including the installation of the fan blades, before testing of the remote control. Y our remote control (Figure 19) has full control of your fan and light. 1. Restore electrical power to the outlet box by turning the electricity on at the service panel.
13 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury .
14 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers.
15 Repair Parts Listing Part Number Key Model No. No. Description KF160OI01 * Hanger Pack, Consisting of: 761655-37 1 Hanger Bracket — 2 Hanger Ball — 3 Downrod — * Parts Bag, Containing: 762658.
LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered.
An important point after buying a device Emerson KF160OI01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Emerson KF160OI01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Emerson KF160OI01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Emerson KF160OI01 you will learn all the available features of the product, as well as information on its operation. The information that you get Emerson KF160OI01 will certainly help you make a decision on the purchase.
If you already are a holder of Emerson KF160OI01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Emerson KF160OI01.
However, one of the most important roles played by the user manual is to help in solving problems with Emerson KF160OI01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Emerson KF160OI01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
