Instruction/ maintenance manual of the product CF200n100 Emerson
Go to page of 16
Part No. F40BP73540001 Form No. BP7354-1 U.L. Model No.: CF200 READ AND SA VE THESE INSTRUCTIONS Net Weight: 22.1 Lbs. CITYSCAPE ™ Ceiling Fan Owner's Manual Model Number s CF200NI00 Br ushed N.
W ARNING: T o avoid fire, shock, and serious personal injury , follow these instruc- tions. Safety Instructions 1. Read your owner ’s manual carefully and keep it for future reference.
3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper One stepladder Six wire connectors (supplied) Materials Wiring, outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following sizes: Installed Wire Length Wire Size A.
Preset Memory Feature Y our remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the switch being turned off.
2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter .
be mated correctly (color-to-color) before they can be engaged. Make sure the connectors close properly . 7. Connect the white wires from the light fitter to the white wire in the switch housing (Figure 5). Connect the black wire from the light fitter to the blue wire in the switch housing.
12. T ighten the setscrews (Figure 8) securely while pulling up on the downrod. NOTE: The setscrews must be properly installed as described above, or fan wobble could result. 13. Make sure the grommet Is properly installed in the coupling cover , then slide the coupling cover over the downrod until it rests on the motor housing.
(Figure 1 1). Hold the rod support in this position while tightening all six decorative rod screws securely . 18. Place the ceiling cover over the down- rod. Then reinstall the hanger ball (Figure 12) on the downrod as follows. Route the three 80” motor leads through the hanger ball and slide the hanger ball over the downrod.
2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 15). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 14).
1. Position the supply wires to the left side of the outlet box (Figure 16); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 16. NOTE: Make all wiring connections using wire connectors (supplied).
7. Screw the 75-watt (maximum) halogen bulb (supplied) into the light fitter sock- et (Figure 19). Do not touch the glass bulb; use the porcelain base to screw in the bulb, or wear soft gloves. CAUTION: T o avoid risks of burns or other injury , assure power is off before attempting to install or replace the halogen bulb.
Operating Y our Ceiling Fan IMPORT ANT Fan installation must be completed, including the installation of the fan blades, before testing of the remote control. Y our remote control (Figure 20) has full control of your fan and light. However , air- flow direction is controlled by a slide switch on the switch housing.
Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury .
14 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. 2. Loose power line 2. Check line power connections connections to the fan, or to fan and wire.
Repair Parts Listing Part Numbers Key Model No. Model No. N o . Description CF200NI00 CF200GES00 * Hanger Pack, Consisting of: 761655-38 761655-39 1 Hanger Bracket — — 2 Hanger Ball — — 3 Down.
LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered.
An important point after buying a device Emerson CF200n100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Emerson CF200n100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Emerson CF200n100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Emerson CF200n100 you will learn all the available features of the product, as well as information on its operation. The information that you get Emerson CF200n100 will certainly help you make a decision on the purchase.
If you already are a holder of Emerson CF200n100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Emerson CF200n100.
However, one of the most important roles played by the user manual is to help in solving problems with Emerson CF200n100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Emerson CF200n100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
