Instruction/ maintenance manual of the product 6.3.0 Elo TouchSystems
Go to page of 14
Elo Touch Solutions Multi-touch Driver Package User Manual Elo Touch Solution s 1033 McCarthy Blvd Milpitas, CA 95035 Package Version: 6.3.0 Release Date: July 17, 2014 Supported OS: W ind ows XP W ind ows 7 W ind ows 8 / 8.
1.1 Installation • Double click on EloSetup .exe • Accept the installation ag ree ment and proceed wi th the insta llation pro cess. 1.2 Uninstallatio n • Launch the Control Pan el and choos e Progra ms and Features. • Select to re move “Elo Tou ch Solutions 6.
3. Configuration Program: EloConfig.exe This is the c onfiguration tool for t he Elo Multi-Touch driv ers. The set up program will launch t he tool at the end of the ins tallation.
The Elo calibration tool is used to calibrate touch recognition on supported Elo t ouch screen monitors. After touching all 3 targets, the screen will show "Accept " and "Retry" buttons.
Launching “Touch Screen Properties” wi ll display various properties of each connected ( and supported) El o touch screen suc h as Monitor Resolution, Co ntroller Serial Number, Controller Firmware Version, etc. In addition to this information, users will be given the ability to “D isable Touch” and “Restore def ault calibrat ion”.
To en able CEA, click on the "Select D efault" butt on and specify the desired parameters. The position of CEA ma y be manipulated for all edges at once b y means of t he “Increase/ Decrease CEA Area” b uttons, or individ ually b y means of the a rrows along eac h edge.
section [ Calibration], c hange the value " DriverCalibration" to 1. User does not need t o reinstall t he package for this change t o take effec t. 3.4 Common Setti ngs Configure shared touch screen settings s uch as “ Beep on Touch”, “Touch M ode”, hiding t he cursor during calibratio n, and spanned displa y mode.
3.4.3 Hide curs or duri ng calibratio n Enabling the set ting will hide the mous e cursor when running the calibrat ion utility. Disabling the sett ing will display the mous e cursor when running t he calibration ut ility. Note: The user must click “Apply” f or a ll changes to take eff ect.
touch zone. • The user can drag t his second box t o any touch screen and adjust it s size and posit ion. • It may be spec ified in t he “EloTouchZones” dialog box whether t ouch wil l be enabled “ inside” or “out side” the zone.
4. Instructions for Window s 7 Emb edded The fo llowing notes are intended as a guide f or enabling mult i-touch func tionality with W indows 7 Embedded. 4.1 Use Ta p.exe to generat e a PMQ f ile including all hardware information of the target system.
monitor needs to be power cycled, t hen re-calibrated to r estore normal t ouch. If powe r c ycling the monitor is not workin g, the utilti y EloCalMgr.exe (located in the t arget installation folder) can be us ed to re set the controller. 6. Appendix 6.
and se parated b y a s pace; No H EX or C HARs. The 8 numbers repres ent t he 8-byte Smartset Command. 6.2.2 Smar tset Comman d Limitati ons: There is no limit to the number of Smartset comman ds that can be sent.
Release 4.0.2 • Serial driver: New calibration is not taking eff ect. • Serial driver: After reboot, previous calibration is not applied. • Serial driver: Pre-install either legacy serial driver or multi-touc h serial driver (not both). Release 4.
• Correct t he pCap firmware ve rsion shown in the propert y page. • Support both new and old f irmware fo r Optical t ouch monitors. • Provide opt ions to limit nu mber of to uches (please see Readm e). • IDS improveme nts: slow response, incorrec t initial touch status, incorrec t power status report.
An important point after buying a device Elo TouchSystems 6.3.0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Elo TouchSystems 6.3.0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Elo TouchSystems 6.3.0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Elo TouchSystems 6.3.0 you will learn all the available features of the product, as well as information on its operation. The information that you get Elo TouchSystems 6.3.0 will certainly help you make a decision on the purchase.
If you already are a holder of Elo TouchSystems 6.3.0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Elo TouchSystems 6.3.0.
However, one of the most important roles played by the user manual is to help in solving problems with Elo TouchSystems 6.3.0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Elo TouchSystems 6.3.0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
