Instruction/ maintenance manual of the product WT30H208DU Electrolux
Go to page of 18
3 ENGLISH A SAFETY INSTRUCTIONS ............. ................................ ............... .................... Pag. 4 B GENERAL RECOMMENDATIONS ........ ................................................. ......... Pag. 5 B1 HANDLING .... .........
4 To reduce the r isk of fire, electrical shock, or injury wh en using your dishwasher, please follow the se basic pre- cautions including the following: • Read all instructions before using your dishwash er. • This Manual does not cover every possible con dition an d situation that may occur.
ENGLISH 5 WARNING CAREFULLY READ THE INSTALLATION OPERA - TING AND MAINTENANCE INSTRUCTIONS BEFORE INSTALLING THIS APPLIANCE. INCORRECT INSTALLATION, ADAPTATIONS OR ALTERNATIONS COULD CAUSE DAMAGE TO PROPERTY OR PER- SONAL INJURY.
6 the regulations in for ce in the country where the product is to be used. B3 DISPOSAL OF PACKING MATERIAL All the packaging materials are envir onmentally safe an d friendly. They maybe kept withou t fear or danger. They may be recycled or burned in a special waste incinera- tion plant.
ENGLISH 7 B4 TECHNICAL DATA Standard cycle time m ay vary should the inlet water temperature be different from tha t indicated above. MODEL WT30H WT30H Supply voltage: 208V, 1ph, 60Hz 33amp 240V, 1ph, 60Hz, 29amp field upgrade to 208V, 3ph 60Hz 20amp 240V, 3ph, 60Hz, 18amp Total Watts 6.
8 Figure 4 Legend Figure 4 A - Water inlet p ipe with 3/4” dia/19mm f ittings C - Outlet pipe 1 5/8” ID /40 mm (^) –11 /16” ID /1 8 mm (*). I - Power supply S - Detergent connection Q - Equipo.
ENGLISH 9 A fused disconne ct switch or a main circuit breaker (customer f urnished) MUST be installed in the electric su pply lin e for th e appliance.
10 Power supply 208 V 1ph or 24 0 V 1ph Figure 8 Open the power supply terminal box and insert the jum- pers provided as follows: two jumpers between terminals 1, 3, 5 and another two between terminals 2, 4 and 6. Using a suitable power supply cable connect L1 and L2 to terminals 5 and 6 respectively and the ground wire to the terminal .
ENGLISH 11 - Check for obstruction on the waste outlet pipe and the overflow aperture. TANK WATER LEVEL TOO HIGH - Check for obstruction on the waste outlet pipe and the overflow aperture.
12 Figure 13 Connect the rinse- aid dispenser betwee n terminals 8 and 9. These connect ion points are live during filling of the tank and at the end of th e rinse cycle for a set time (see “setting the dispensers” para graph).
ENGLISH 13 Exit from programming mode: Notes for external dispensers: -i f dEt=181 the deterg ent disp enser only oper- ates during wash pump operation; terminals 7 and 9 of the main termin al box are powered at the same time.
14 Our appliances have been studied and optimized to give the highest perform ance. This ap pliance must be used exclusi- vely for the purp ose for which it has be en designed, i.e. fo r washing dishes with water and specific detergents. Any other use will be considered “improper use” and will void the warran ty and manufacturer liability.
ENGLISH 15 system save up to 30% in time over traditional models. If the door is opened during this stage the message "CLOSE" will scroll on the display: The filling and heati ng stage has f.
16 • BLUE rack for glasse s: the glasses should be placed upside down. Figure 16 D4 END OF WORK AND DA ILY CLEANING The appliance is designe d to carry out an automatic cleaning cycle to help flush out any residues and to guarantee greater health and hygiene : • Open the door and take out the r ack containing the clean dishes.
ENGLISH 17 D5 MAINTENANC E DELIMING WARNING : DELIMING SOLUTION, RINSE AGENTS OR ANY OTHER KIND OF A CID MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN CHEMICAL-SANITI- ZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM.
18 cedure describe d in the paragraph “Manu al activa- tion” at le ast 3 time s. • Completely drain the boiler by simultaneou sly pres- sing the buttons as shown in the figure. A buzzer indicates completion of drainage. • Spread a thin film of petroleum jelly over all the stain- less steel surfaces .
ENGLISH 19 • Pour approx. 1.5 kg of co arse salt [NaCl] in container "A" (an amount sufficient to fill the salt container up to the rim) using the special funnel supplied (Fi g u r e 21 ) . Figure 21 • Remove any traces of salt from the filling hole, the container thread an d the closing cap seal.
20 E TROUBLESHOOTING DISHWASHER DOES NOT WASH WELL 1. Check if the suction filter is dirty, if so clean it thoroughly. 2. Check if the wash jets are clogged by solid food pa rticles. 3. Check that the initial a mount of dete rgent or subseq uent additions are co r- rect.
An important point after buying a device Electrolux WT30H208DU (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux WT30H208DU yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux WT30H208DU - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux WT30H208DU you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux WT30H208DU will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux WT30H208DU, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux WT30H208DU.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux WT30H208DU. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux WT30H208DU along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
