EN
Alcatel-Lucent logo
Official user manual

Alcatel-Lucent IP Phone (740)

92 pages·1.4 MB·IP Phone·PDF·ENDEFRITNLJA
Alcatel-Lucent IP Phone (740)
Table of Contents 74 sections OmniAccess 740 Hardware Users Guide · Chapter 1 Preface · About this Guide · Chapter Description · … ShowHide
OmniAccess 740 Hardware Users Guidep.1Chapter 1 Prefacep.9About this Guidep.9Chapter Descriptionp.9Audiencep.9Document Organizationp.10Document Conventionsp.10Obtaining Documentationp.11Reference Publicationsp.11Obtaining Technical Assistancep.11Documentation Feedbackp.11Chapter 2 OmniAccess 740 Overviewp.13Introductionp.13OA-740 Overviewp.14Package Contentsp.14Hardware Overviewp.15The OA-740p.15User Modulesp.21System Specificationsp.32Valid System Configurationp.32Chapter 3 Installing the OmniAccess 740p.33Preparing for Installationp.34Required Tools and Equipmentp.34Installation Checklistp.34Safety Measuresp.35Preventing Injuryp.35Equipment Guidelinesp.36Lifting Safelyp.37Safety with Electricityp.37Preventing Electrostatic Discharge Damagep.38Site Requirement Guidelinesp.39Power Supply Overviewp.40Power Supply Specificationsp.40Plant Wiringp.42General Installationp.43Rack-Mounting the OA-740p.44Parts Requiredp.45Installing the OA-740 in the Rackp.46Installing User Modulesp.47Installing Line Cardsp.47Installing Fillersp.48Chapter 4 Starting the OmniAccess 740p.49Introductionp.49Checking Conditions Prior to System Startupp.50Starting the OA-740p.50Connecting to the System Console Portp.52Performing Basic Configuration Tasksp.54Accessing OA-740 Through CLIp.54Connecting the System to the Networkp.59Connecting to Internal Networkp.59Connecting Through External Networkp.62Site Logp.63Appendix A Regulatory Compliance and Safety Informationp.65Declaration of Conformity: CE Markp.65Waste Electrical and Electronic Equipment (WEEE) Statementp.66China RoHS: Hazardous Substance Tablep.67Standards Compliancep.69Safetyp.69EMCp.69Telecomp.69Declaration of Conformity Addendump.70FCC Class A, Part 15p.71Canada Class A Statementp.72JATEp.72CISPR22 Class A warningp.72VCCIp.72Class A Warning for Taiwan and Other Chinese Marketsp.73Appendix B Appendix B AC Power Specificationsp.80Appendix C Appendix C Pin Connector Details for OmniAccess 740p.82RJ-11 Modem Connector Pin Assignmentsp.82RJ-45 Console Connector Pin Assignmentsp.83T1E1 Connector Pin Assignmentsp.84SE/L2GE Connector Pin Assignmentsp.85Serial Card (V.35/X.21) Connector Pin Assignmentsp.86
Page 1 of the Alcatel-Lucent IP Phone (740) user manual — FAX (818) 880-3505
Page 1 · click to enlarge
Page 1

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

OmniAccess 740 Hardware Users Guide

Release 2.2

FAX (818) 880-3505

Beta

support@ind.alcatel.com

US Customer Support—(800) 995-2696

International Customer Support—(818) 878-4507

Internet—service.esd.alcatel-lucent.com

Websitewww.alcatel-lucent.com
Part No032288-00, Rev. A

Calabasas, CA 91301 · (818) 880-3500

Page 2 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740 Hardware Users Guide
Page 2 · click to enlarge
Page 2

The Specifications and Information regarding the products in this manual are subject to change without notice. All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind, express or implied. Users must take full responsibility for their application of any products.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE.

This equipment has been tested and found to comply within the limits pursuant to the (Centre for Telecom) rules. These limits are designed to provide protection against harmful interference when the equipment is operated in a commercial environment.

The following information is for the Users of the OmniAccess 740: If it is not installed in accordance with the installation instructions, it may not function exactly to the said specifications. Modifying the equipment without Alcatel-Lucent's written authorization may result in the equipment no longer complying with the said dimensions.

Copyright © 2007, Alcatel-Lucent. All rights reserved.

Not withstanding any other warranty herein, all hardware and software are provided "as is" with all faults. Alcatel-Lucent disclaim all warranties, expressed or implied, including, without limitation, those of merchantability, fitness for a particular purpose and non-infringement or arising from a course of dealing, usage, or trade practice. In no event shall Alcatel-Lucent be liable for any indirect, special, consequential, or incidental damages, including, without limitation, lost profits or loss or damage to data arising out of the use or inability to use this manual, even if Alcatel-Lucent have been advised of the possibility of such damages.

Copyright

Page 3 of the Alcatel-Lucent IP Phone (740) user manual — Table of contents
Page 3 · click to enlarge
Page 3

Table of contents

OmniAccess 740 Hardware Users Guidep.1Chapter 1 Prefacep.9About this Guidep.9Chapter Descriptionp.9Audiencep.9Document Organizationp.10Document Conventionsp.10Obtaining Documentationp.11Reference Publicationsp.11Obtaining Technical Assistancep.11Documentation Feedbackp.11Chapter 2 OmniAccess 740 Overviewp.13Introductionp.13OA-740 Overviewp.14Package Contentsp.14Hardware Overviewp.15The OA-740p.15User Modulesp.21System Specificationsp.32Valid System Configurationp.32Chapter 3 Installing the OmniAccess 740p.33Preparing for Installationp.34Required Tools and Equipmentp.34Installation Checklistp.34Safety Measuresp.35Preventing Injuryp.35Equipment Guidelinesp.36Lifting Safelyp.37Safety with Electricityp.37Preventing Electrostatic Discharge Damagep.38Site Requirement Guidelinesp.39Power Supply Overviewp.40Power Supply Specificationsp.40Plant Wiringp.42General Installationp.43Rack-Mounting the OA-740p.44Parts Requiredp.45Installing the OA-740 in the Rackp.46Installing User Modulesp.47Installing Line Cardsp.47Installing Fillersp.48Chapter 4 Starting the OmniAccess 740p.49Introductionp.49Checking Conditions Prior to System Startupp.50Starting the OA-740p.50Connecting to the System Console Portp.52Performing Basic Configuration Tasksp.54Accessing OA-740 Through CLIp.54Connecting the System to the Networkp.59Connecting to Internal Networkp.59Connecting Through External Networkp.62Site Logp.63Appendix A Regulatory Compliance and Safety Informationp.65Declaration of Conformity: CE Markp.65Waste Electrical and Electronic Equipment (WEEE) Statementp.66China RoHS: Hazardous Substance Tablep.67Standards Compliancep.69Safetyp.69EMCp.69Telecomp.69Declaration of Conformity Addendump.70FCC Class A, Part 15p.71Canada Class A Statementp.72JATEp.72CISPR22 Class A warningp.72VCCIp.72Class A Warning for Taiwan and Other Chinese Marketsp.73Translated Safety Warningsp.74Appendix B Appendix B AC Power Specificationsp.80Appendix C Appendix C Pin Connector Details for OmniAccess 740p.82RJ-11 Modem Connector Pin Assignmentsp.82RJ-45 Console Connector Pin Assignmentsp.83T1E1 Connector Pin Assignmentsp.84SE/L2GE Connector Pin Assignmentsp.85Serial Card (V.35/X.21) Connector Pin Assignmentsp.86
Page 4 of the Alcatel-Lucent IP Phone (740) user manual — Table of contents
Page 4 · click to enlarge
Page 4

Table of contents

OmniAccess 740 Hardware Users Guidep.1Chapter 1 Prefacep.9About this Guidep.9Chapter Descriptionp.9Audiencep.9Document Organizationp.10Document Conventionsp.10Obtaining Documentationp.11Reference Publicationsp.11Obtaining Technical Assistancep.11Documentation Feedbackp.11Chapter 2 OmniAccess 740 Overviewp.13Introductionp.13OA-740 Overviewp.14Package Contentsp.14Hardware Overviewp.15The OA-740p.15User Modulesp.21System Specificationsp.32Valid System Configurationp.32Chapter 3 Installing the OmniAccess 740p.33Preparing for Installationp.34Required Tools and Equipmentp.34Installation Checklistp.34Safety Measuresp.35Preventing Injuryp.35Equipment Guidelinesp.36Lifting Safelyp.37Safety with Electricityp.37Preventing Electrostatic Discharge Damagep.38Site Requirement Guidelinesp.39Power Supply Overviewp.40Power Supply Specificationsp.40Plant Wiringp.42General Installationp.43Rack-Mounting the OA-740p.44Parts Requiredp.45Installing the OA-740 in the Rackp.46Installing User Modulesp.47Installing Line Cardsp.47Installing Fillersp.48Chapter 4 Starting the OmniAccess 740p.49Introductionp.49Checking Conditions Prior to System Startupp.50Starting the OA-740p.50Connecting to the System Console Portp.52Performing Basic Configuration Tasksp.54Accessing OA-740 Through CLIp.54Connecting the System to the Networkp.59Connecting to Internal Networkp.59Connecting Through External Networkp.62Site Logp.63Appendix A Regulatory Compliance and Safety Informationp.65Declaration of Conformity: CE Markp.65Waste Electrical and Electronic Equipment (WEEE) Statementp.66China RoHS: Hazardous Substance Tablep.67Standards Compliancep.69Safetyp.69EMCp.69Telecomp.69Declaration of Conformity Addendump.70FCC Class A, Part 15p.71Canada Class A Statementp.72JATEp.72CISPR22 Class A warningp.72VCCIp.72Class A Warning for Taiwan and Other Chinese Marketsp.73Translated Safety Warningsp.74Appendix B Appendix B AC Power Specificationsp.80Appendix C Appendix C Pin Connector Details for OmniAccess 740p.82RJ-11 Modem Connector Pin Assignmentsp.82RJ-45 Console Connector Pin Assignmentsp.83T1E1 Connector Pin Assignmentsp.84SE/L2GE Connector Pin Assignmentsp.85Serial Card (V.35/X.21) Connector Pin Assignmentsp.86
Page 5 of the Alcatel-Lucent IP Phone (740) user manual — Table of contents
Page 5 · click to enlarge
Page 5

Table of contents

OmniAccess 740 Hardware Users Guidep.1Chapter 1 Prefacep.9About this Guidep.9Chapter Descriptionp.9Audiencep.9Document Organizationp.10Document Conventionsp.10Obtaining Documentationp.11Reference Publicationsp.11Obtaining Technical Assistancep.11Documentation Feedbackp.11Chapter 2 OmniAccess 740 Overviewp.13Introductionp.13OA-740 Overviewp.14Package Contentsp.14Hardware Overviewp.15The OA-740p.15User Modulesp.21System Specificationsp.32Valid System Configurationp.32Chapter 3 Installing the OmniAccess 740p.33Preparing for Installationp.34Required Tools and Equipmentp.34Installation Checklistp.34Safety Measuresp.35Preventing Injuryp.35Equipment Guidelinesp.36Lifting Safelyp.37Safety with Electricityp.37Preventing Electrostatic Discharge Damagep.38Site Requirement Guidelinesp.39Power Supply Overviewp.40Power Supply Specificationsp.40Plant Wiringp.42General Installationp.43Rack-Mounting the OA-740p.44Parts Requiredp.45Installing the OA-740 in the Rackp.46Installing User Modulesp.47Installing Line Cardsp.47Installing Fillersp.48Chapter 4 Starting the OmniAccess 740p.49Introductionp.49Checking Conditions Prior to System Startupp.50Starting the OA-740p.50Connecting to the System Console Portp.52Performing Basic Configuration Tasksp.54Accessing OA-740 Through CLIp.54Connecting the System to the Networkp.59Connecting to Internal Networkp.59Connecting Through External Networkp.62Site Logp.63Appendix A Regulatory Compliance and Safety Informationp.65Declaration of Conformity: CE Markp.65Waste Electrical and Electronic Equipment (WEEE) Statementp.66China RoHS: Hazardous Substance Tablep.67Standards Compliancep.69Safetyp.69EMCp.69Telecomp.69Declaration of Conformity Addendump.70FCC Class A, Part 15p.71Canada Class A Statementp.72JATEp.72CISPR22 Class A warningp.72VCCIp.72Class A Warning for Taiwan and Other Chinese Marketsp.73Translated Safety Warningsp.74Appendix B Appendix B AC Power Specificationsp.80Appendix C Appendix C Pin Connector Details for OmniAccess 740p.82RJ-11 Modem Connector Pin Assignmentsp.82RJ-45 Console Connector Pin Assignmentsp.83T1E1 Connector Pin Assignmentsp.84SE/L2GE Connector Pin Assignmentsp.85Serial Card (V.35/X.21) Connector Pin Assignmentsp.86
Page 6 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740 Hardware Users Guide
Page 6 · click to enlarge
Page 6
Page 6 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740 Hardware Users Guide
Page 7 of the Alcatel-Lucent IP Phone (740) user manual — Table of contents
Page 7 · click to enlarge
Page 7

Table of contents

OmniAccess 740 Hardware Users Guidep.1Chapter 1 Prefacep.9About this Guidep.9Chapter Descriptionp.9Audiencep.9Document Organizationp.10Document Conventionsp.10Obtaining Documentationp.11Reference Publicationsp.11Obtaining Technical Assistancep.11Documentation Feedbackp.11Chapter 2 OmniAccess 740 Overviewp.13Introductionp.13OA-740 Overviewp.14Package Contentsp.14Hardware Overviewp.15The OA-740p.15User Modulesp.21System Specificationsp.32Valid System Configurationp.32Chapter 3 Installing the OmniAccess 740p.33Preparing for Installationp.34Required Tools and Equipmentp.34Installation Checklistp.34Safety Measuresp.35Preventing Injuryp.35Equipment Guidelinesp.36Lifting Safelyp.37Safety with Electricityp.37Preventing Electrostatic Discharge Damagep.38Site Requirement Guidelinesp.39Power Supply Overviewp.40Power Supply Specificationsp.40Plant Wiringp.42General Installationp.43Rack-Mounting the OA-740p.44Parts Requiredp.45Installing the OA-740 in the Rackp.46Installing User Modulesp.47Installing Line Cardsp.47Installing Fillersp.48Chapter 4 Starting the OmniAccess 740p.49Introductionp.49Checking Conditions Prior to System Startupp.50Starting the OA-740p.50Connecting to the System Console Portp.52Performing Basic Configuration Tasksp.54Accessing OA-740 Through CLIp.54Connecting the System to the Networkp.59Connecting to Internal Networkp.59Connecting Through External Networkp.62Site Logp.63Appendix A Regulatory Compliance and Safety Informationp.65Declaration of Conformity: CE Markp.65Waste Electrical and Electronic Equipment (WEEE) Statementp.66China RoHS: Hazardous Substance Tablep.67Standards Compliancep.69Safetyp.69EMCp.69Telecomp.69Declaration of Conformity Addendump.70FCC Class A, Part 15p.71Canada Class A Statementp.72JATEp.72CISPR22 Class A warningp.72VCCIp.72Class A Warning for Taiwan and Other Chinese Marketsp.73Translated Safety Warningsp.74Appendix B Appendix B AC Power Specificationsp.80Appendix C Appendix C Pin Connector Details for OmniAccess 740p.82RJ-11 Modem Connector Pin Assignmentsp.82RJ-45 Console Connector Pin Assignmentsp.83T1E1 Connector Pin Assignmentsp.84SE/L2GE Connector Pin Assignmentsp.85Serial Card (V.35/X.21) Connector Pin Assignmentsp.86
Page 8 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740 Hardware Users Guide
Page 8 · click to enlarge
Page 8
Page 8 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740 Hardware Users Guide
Page 9 of the Alcatel-Lucent IP Phone (740) user manual — A UDIENCE
Page 9 · click to enlarge
Page 9

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

C HAPTER 1

P REFACE

A BOUT THIS G UIDE

This hardware users guide explains the initial hardware installation and the configuration procedures for the OmniAccess 740 (OA-740). It contains procedures for unpacking and installing the OA-740 system hardware, starting up the system, and creating a basic configuration. After completing the installation and basic configuration procedures covered in this guide, use the appropriate companion publications to more completely configure your system.

C HAPTER D ESCRIPTION

This chapter explains the objectives, intended audience, organization of the OA-740 Hardware Users Guide, and defines the conventions used to convey instructions and information.

A UDIENCE

This book is intended for networking professionals who are responsible for designing, implementing, and managing enterprise networks. This book aims to provide unique technology and effective practices that deliver value on the networking perspective.

  • The user is expected to have, at minimum, an introductory understanding of the following:
  • Networking applications
  • Telecommunication networks
  • Hardware configuration
PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 10 of the Alcatel-Lucent IP Phone (740) user manual — D OCUMENT C ONVENTIONS
Page 10 · click to enlarge
Page 10

D OCUMENT O RGANIZATION

This hardware users guide is organized into following chapters and appendix:

Chapter 2 OmniAccess 740 Overview describes the functional description of OA-740 and provides functional overview of the system.

Chapter 3 Installing the OmniAccess 740 is a preparatory chapter that describes safety considerations, tools required, an overview of the installation, and hardware installation procedures.

Chapter 4 Starting the OmniAccess 740 provides procedure for starting the OA- 740, performing basic configuration tasks, and connecting the system to internal and external networks.

Appendix provides additional information on the regulatory compliances and safety, AC power supply, and Pin Connector details for the OA-740.

D OCUMENT C ONVENTIONS

The following conventions are used to attract the attention of the reader:

equipment damage or loss of data.

Safety Warnings:

Means reader be extremely cautious. Failure to observe the warning note could result in injury to the user, equipment damage, and/or loss of data.

This warning means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

Page 11 of the Alcatel-Lucent IP Phone (740) user manual — D OCUMENTATION F EEDBACK
Page 11 · click to enlarge
Page 11

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

O BTAINING D OCUMENTATION

Alcatel-Lucent provides several ways to obtain technical assistance and other technical resources. Documents can be downloaded from our support site service.esd.alcatel-lucent.com.

R EFERENCE P UBLICATIONS

  • The following publications are a part of the Alcatel-Lucent documentation suite:
  • OmniAccess 700 CLI Command Reference Guide (Release 2.2)
  • OmniAccess 700 CLI Configuration Guide (Release 2.2)
  • OmniAccess 700 Web GUI Users Guide (Release 2.2)
  • OmniAccess 700 Getting Started Guide (Release 2.2)
  • OmniAccess 780 Hardware Users Guide (Release 2.2)

O BTAINING T ECHNICAL A SSISTANCE

For all customers, partners, resellers, and distributors who hold valid Alcatel-Lucent service contracts, the Alcatel-Lucent Technical Support Team provides 24-hour-a-day, technical support services online and over the phone.

For Customer issues and help, contact:

US Customer Support(800) 995-2696
International Customer Support(818) 878-4507
E-mailsupport@ind. alcatel.com
Websiteservice.esd. alcatel-lucent.com

D OCUMENTATION F EEDBACK

We value your comments and suggestions about our documentation. If you have any comments about this book, please enter them through the feedback link on the Alcatel-Lucent Website. We will use your feedback in our plans to improve the documentation.

Obtaining Documentation · Alcatel-Lucent

Page 12 of the Alcatel-Lucent IP Phone (740) user manual — Obtaining Documentation
Page 12 · click to enlarge
Page 12
Page 12 of the Alcatel-Lucent IP Phone (740) user manual — Obtaining Documentation
Page 13 of the Alcatel-Lucent IP Phone (740) user manual — C HAPTER 2
Page 13 · click to enlarge
Page 13

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

C HAPTER 2

OmniAccess 740 O VERVIEW

I NTRODUCTION

This chapter provides physical and functional overview of the OmniAccess 740 (OA-740). It contains the functional description of OA-740 hardware, its major components, and related features. Descriptions and examples of software commands are included only when they are necessary for replacing, installing, configuring, or maintaining the OA-740 hardware.

This chapter contains the following sections:

  • OA-740 Overview
  • Package Contents
  • Hardware Overview
  • System Specifications
PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 14 of the Alcatel-Lucent IP Phone (740) user manual — P ACKAGE C ONTENTS
Page 14 · click to enlarge
Page 14

OA-740 O VERVIEW

The OA-740 is designed to provide most commonly used network services, such as routing, switching, wide area network (WAN) connectivity, network security with firewall, and related services.

P ACKAGE C ONTENTS

1. The OA-740
  • 4-slot Chassis that includes
  • Services Engine (SE) - 2-port 10/100/1000 Mbps Ethernet
  • 3 Fans (built-in)
  • Power Supply (built-in)
2. Optional Modules
  • 4-port T1E1 Line Card
  • 8-port 10/100/1000 Mbps Gigabit Ethernet (GigE) Line Card
  • 4-port Serial Line Card (V3.5/X.21)
3. Miscellaneous
  • AC Power Cord
  • Console Cable
  • Rack Mount Screws
  • 19-inch Rack Mount Ears
  • 512 MB USB Memory Flash
  • Product Documentation CD ROM

OmniAccess 740 Overview

Page 15 of the Alcatel-Lucent IP Phone (740) user manual — T HE OA-740
Page 15 · click to enlarge
Page 15

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

H ARDWARE O VERVIEW

The following section provides a detailed overview of the hardware components of OA-740.

T HE OA-740

OA-740 has 4 line card slots, numbered 0 to 3 from left to right. The slots 2 and 3 can be combined to support a dual slot line card (such as the SE). All the OA-740 cards support Online Insertion and Removal (OIR) feature.

  • The OA-740 has the following components:
  • OA-740 Chassis
  • SE

Hardware Overview

Page 16 of the Alcatel-Lucent IP Phone (740) user manual — 1. SE
Page 16 · click to enlarge
Page 16

OA-740 C HASSIS

OA-740 chassis is a rigid sheet metal structure that houses the other hardware components. one rack-unit (1 RU) chassis has a front panel, a rear panel, and perforated side panels for air flow. The chassis also integrates a power supply unit and a cooling unit.

The chassis is of 1.73-inch (4.4 cm) height, 17.5-inch (44.5 cm) width, and 17-inch (43.2 cm) depth. It weighs approximately 26.4 lbs (12.8 kgs).

Figure 1 shows an OA-740 chassis.

Alcatel-Lucent IP Phone (740) — OA-740 C HASSIS diagram (page 16)
Fig. 1

1. SE

2. 4-port T1E1 Line Card
3. Rack Mount Flange
Figure 1The OA-740 Chassis

OmniAccess 740 Overview

Page 17 of the Alcatel-Lucent IP Phone (740) user manual — Hardware Overview
Page 17 · click to enlarge
Page 17

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Table 1 summarizes the physical specifications of the OA-740 chassis.

Table 1OA-740 Chassis Physical Specifications
Alcatel-Lucent IP Phone (740) — Hardware Overview diagram (page 17)
Fig. 2 · Hardware Overview

Figure 2 shows the air flow pattern through OA-740 chassis.

Alcatel-Lucent IP Phone (740) — Hardware Overview diagram (page 17)
Fig. 3 · Hardware Overview
Figure 2Air Flow Through the OA-740

The chassis has a built-in power supply system which provides power for all the OA-740 components. (Refer to the “AC Power Specifications” chapter for power supply specifications.) The chassis also has built-in fans for efficient cooling of the OA-740, which prevents damages due to overheating of the OA-740 components.

Hardware Overview

Page 18 of the Alcatel-Lucent IP Phone (740) user manual — OA7-T1E1-4 OA7-SE
Page 18 · click to enlarge
Page 18

The front panel houses SE, line cards, status LEDs, communication ports, and card ejectors. The communication ports on the front panel provide LAN/WAN and console connectivity to the system. All the cards in the front panel dock into respective slots in the back plane. The front panel also houses rack-mount flanges that help the system to be loaded on to a 19-inch rack.

OA7-T1E1-4 OA7-SE

OA7-6E-8

Figure 3Front Panel

The rear panel provides power supply connectivity to the OA-740.

Figure 4Rear Panel

OmniAccess 740 Overview · USB Modem Console · OmniAccess 740

Page 19 of the Alcatel-Lucent IP Phone (740) user manual — LED I NFORMATION
Page 19 · click to enlarge
Page 19

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

S LOT N UMBERS

The slots in the front panel are numbered 0 through 3, from left to right.

The table below lists the slot number and the component associated with it.

Table 2Slot Numbers

Slot Number Location Slot Type Card Associated With the Slot

0 Front Panel Single Line Card

1 Front Panel Single Line Card

2 Front Panel Dual SE

3 Front Panel Dual SE

0 1 2 3

Figure 5OA-740 (4-Slot Chassis)

LED I NFORMATION

The following table shows the state of the main LEDs after startup.

Table 3LED Status

Active Off Power up status. This is the default display when the system is first powered on and before the software is loaded.

Green SE card is active.

Yellow Indicates transient conditions (e.g., booting).

Show 6 more labels / short text on this page
Hardware Overview · Number · USB Modem Console · OmniAccess 740 · LED Status Description · SE LEDs
Page 20 of the Alcatel-Lucent IP Phone (740) user manual — B ACK P LANE
Page 20 · click to enlarge
Page 20

C ABLE C ONNECTION T ABLE

The following table summarizes the cable connections for the OA-740.

Table 4Cable Connections

Port or Module Port Type Connect To

Power Unit IEC 60320 (320) C-14 Power Inlet Main power supply.

Ethernet RJ-45 Ethernet hub or switch.

T1E1 RJ-45 T1E1 network.

Console RJ-45 PC or VT100

Modem RJ-11 Telephone Line

Serial 68 pin VHDCI Connector V.35/X.21 modem

B ACK P LANE

The back panel in the OA-740 provides docking slots for the SE card, the line cards, and performs switching functions.

OmniAccess 740 Overview

Page 21 of the Alcatel-Lucent IP Phone (740) user manual — OA7-SE
Page 21 · click to enlarge
Page 21

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

U SER M ODULES

This section provides description about the modules/components that can be installed by the user.

L INE C ARDS

All the line cards can be mounted on a single slot except the SE card, which requires two slots. Next generation SE line cards may occupy a single slot only. An overview of the line cards is given below.

S ERVICES E NGINE

The SE card is the main data processing center in the chassis. The SE card has two external auto-negotiable copper GigE ports. The GigE interfaces can auto- negotiate, transmit, and receive data packets at the rate of 10/100/1000 Mbps.

The LEDs on the SE card indicate Active or Fault conditions. The LEDs on the Gigabit Ethernet ports of the SE card indicate Link Status, Link Speed, and Activity. The SE card is a dual slot line card, and is installed in slots 2, 3.

OA7-SE

1. SE LEDs
2. GigE Ports
3. Thumb Screw
4. Left LED on the Ethernet Port
5. Right LED on the Ethernet Port
Figure 6Services Engine

Hardware Overview

Page 22 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 22 · click to enlarge
Page 22

SE card has status LEDs for the card and for each of its Ethernet ports.

Table 5SE Card LEDs

Active Green SE card is active.

Fault Red Reload in progress.

Table 6LEDs for Ethernet Port on SE Card

Left LED Green Link Speed is 1000/10 Mbps.

Yellow Link Speed is 100 Mbps.

Off Link is not active

Right LED Amber Traffic is active.

Off Traffic is not active.

Show 4 more labels / short text on this page
OmniAccess 740 Overview · SE Card LEDs · LED Status Description · LED Status Description
Page 23 of the Alcatel-Lucent IP Phone (740) user manual — OA7-T1E1-4
Page 23 · click to enlarge
Page 23

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

4PORT T1E1 L INE C ARD

The 4-port T1E1 line card supports American and European (International) digital transmission standards. The card is a single slot line card, and is installed either in slot 0 or 1. The 4-port T1E1 line card has 4 RJ-45 interfaces. Each interface can support data rates of 1.544 or 2 Mbps depending on the type of connectivity.

The figure below shows the 4-port T1E1 Line Card.

OA7-T1E1-4

1 2 3 5 4

1. T1E1 Card LEDs
2. T1E1 Mode LEDs
3. T1E1 Port LEDs
4. RJ-45 Interfaces
5. Thumb Screw
Figure 74-port T1E1 Line Card

Hardware Overview

Page 24 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 24 · click to enlarge
Page 24

4-port T1E1 Line Card LEDs

The LEDs on the 4-port T1E1 line card indicate Active or Fault condition; T1 mode, E1 Balanced (E1B) mode, and E1 Unbalanced (E1U) mode. The 4x4 LEDs on the front of the card indicate Local Alarm, Remote Alarm, Carrier Detect, and Loopback for the 4 ports.

The following tables describe the status of LEDs on the 4-port T1E1 line card.

Table 7T1E1 Card LEDs

Active Green 4-port T1E1 line card is active.

Yellow Indicates transient conditions (e.g., booting).

Fault Red Reload in progress.

Table 8T1E1 Port LEDs

Local Alarm (LA) On Indicates either Red or Yellow alarm present or Transmitting Blue/AIS alarm.

Off Indicates neither Red nor Yellow alarm is present and transmitter also not transmitting AIS/Blue Alarm.

Remote Alarm (RA) On Remote System is transmitting Blue/ AIS alarm.

Off Remote system is not transmitting any alarm.

Carrier Detect (CD) On Carrier detected (cable plugged in).

Off Carrier not detected (cable plugged out).

Loopback (LB) On Indicates port is in any of the local or network Loopback mode.

Off Port is not in Loopback mode.

OmniAccess 740 Overview · LED Status Description · LED Status Description

Page 25 of the Alcatel-Lucent IP Phone (740) user manual — LED4 LED3 LED5 LED6 LED7
Page 25 · click to enlarge
Page 25

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Table 9T1E1 Mode LEDs

T1 E1B E1U Description

On Off Off Line card configured in the T1 mode.

Off On Off Line card Configured in the E1 balanced mode.

Off Off On Line card configured in the E1 unbalanced mode.

Off Off Off No mode configured on the line card.

L2 8-PORT GIGABIT ETHERNET LINE CARD

The 8-port GigE line card provides Layer-2 switching functions. The card is a single slot line card, and is installed either in slot 0 or 1. The GigE card has 8 RJ- 45 interfaces. These interfaces can auto-negotiate, transmit, and receive data packets at the rate of 10/100/1000 Mbps.

GigE Port LED 0 LED1 LED2

LED4 LED3 LED5 LED6 LED7

OA7-GE-8

1. GigE Card LEDs
2. RJ-45 Interfaces
3. Thumb Screw
Figure 8GigE Line Card

Hardware Overview

Page 26 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 26 · click to enlarge
Page 26

GigE Line Card LEDs

The LEDs on GigE line card indicate Active or Fault conditions. The LEDs on each of the ports indicate Link Status and Activity.

The following tables describe the status of LEDs on the GigE card:

Table 10GigE Card LEDs

Active Green GigE card is active.

Yellow Indicates transient conditions (e.g., booting).

Fault Red Reload in progress.

Table 11LEDs for each Port on GigE Card

LED 0 Off Port 0 link is not active.

Solid Green Port 0 link is active.

Blinking Green Port 0 link and traffic is active.

LED 1 Off Port 1 link is not active.

Solid Green Port 1 link is active.

Blinking Green Port 1 link and traffic is active.

LED 2 Off Port 2 link is not active.

Solid Green Port 2 link is active.

Blinking Green Port 2 link and traffic is active.

LED 3 Off Port 3 link is not active.

Solid Green Port 3 link is active.

Blinking Green Port 3 link and traffic is active.

LED 4 Off Port 4 link is not active.

Solid Green Port 4 link is active.

Blinking Green Port 4 link and traffic is active.

OmniAccess 740 Overview · LED Status Description · LED Status Description

Page 27 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 27 · click to enlarge
Page 27

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

LED 5 Off Port 5 link is not active.

Solid Green Port 5 link is active.

Blinking Green Port 5 link and traffic is active.

LED 6 Off Port 6 link is not active.

Solid Green Port 6 link is active.

Blinking Green Port 6 link and traffic is active.

LED 7 Off Port 7 link is not active.

Solid Green Port 7 link is active.

Blinking Green Port 7 link and traffic is active.

Hardware Overview · LED Status Description

Page 28 of the Alcatel-Lucent IP Phone (740) user manual — OA7-USP-2
Page 28 · click to enlarge
Page 28

S ERIAL L INE C ARD (V.35/X.21)

Serial Card (V.35/X.21) provides WAN termination for four ports over serial sync interfaces. The card is a single slot line card, and is installed either in slot 0 or 1. The card allows full duplex operation on a single copper pair and operates in either DTE of DCE mode depending on the cable attached.

V.35 and X.21 are well known communication protocols over synchronous serial lines.

V.35 Interface

The V.35 interface was originally specified by CCITT as an interface for 48kbps line transmissions. It has been adopted for all line speeds above 20kbps.

V.35 is a mixture of balanced and common earth signal interfaces. The control lines including DTR, DSR. DCD, RTS, and CTS are single wire common earth interfaces. The data and clock signals are balanced signals.

X.21 Interface

The physical interface between the DTE and the DCE is defined in ITU-T recommendation as X.21. The DCE provides a full-duplex, bit-serial, synchronous transmission path between the DTE and the local PSE. It can operate at data rates from 600bps.

OA7-USP-2

1 2 3 4

1. V.35/X.21 Card LEDs
2. V.35/X.21 Port LEDs
3. 68 pin VHDCI Connector
4. Thumb Screw
Figure 9Serial Line Card (V.35/X.21)

OmniAccess 740 Overview

Page 29 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 29 · click to enlarge
Page 29

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Serial Card (V.35/X.21) LEDs

The LEDs on the Serial line card indicates Active or Fault condition. The 4x4 LEDs on the front of the card indicates the Active Loopback, DTE/DCE, Receive Clock, and Transmit Clock for the 4 ports.

The following tables describe status of LEDs on the Serial card.

Table 12Serial Card (V.35/X.21) LEDs

Active Green Serial card is active.

Yellow Indicates transient conditions (e.g., booting).

Fault Red Reload in progress.

Table 13Serial (V.35/X.21) Port LEDs

Active/LB Green - On Indicates ports are ready and interfaces are enabled.

Green - Off Indicates ports are not ready and interfaces are disabled.

Yellow - On Ports in Loopback Mode.

Yellow - Off Ports are not in Loopback Mode

DTE/DCE Green - On DTE cables are plugged-in

Yellow - On DCE cables are plugged-in

Off Cables not plugged in

RX Clk Green - Flashing DTE Receive Clock In

DCE Receive Clock Out

Off No Receive Clock

TX Clk Green - Flashing DTE Transmit Clock In

DCE Transmit Clock In

Off No Transmit Clock

Hardware Overview · LED Status Description · LED Status Description

Page 30 of the Alcatel-Lucent IP Phone (740) user manual — User Modules
Page 30 · click to enlarge
Page 30

Serial Card (V.35/X.21) Cable Details

The following table lists the part numbers for the Alcatel-Lucent specific V.35/X.21 cables:

Table 14Serial Card (V.35/X.21) Cable Part Numbers

Part No. Description

5100-0010-00 Cable ASSY V.35 DTE Cable with Male Connector (68 Pin SCSI Connector to V.35 DTE Male Connector)

5100-0011-00 Cable ASV.35 DCE Cable with Female Connector (68 Pin SCSI Connector to V.35 DCE Female Connector)

5100-0012-00 Cable ASSY X.21 DTE Cable with Male Connector (68 Pin SCSI Connector to X.21 DB15 Male Connector)

5100-0013-00 Cable AX.21 DCE Cable with Female Connector (68 Pin SCSI Connector to X.21 DB15 Female Connector)

OmniAccess 740 Overview

Page 31 of the Alcatel-Lucent IP Phone (740) user manual — C OOLING U NIT
Page 31 · click to enlarge
Page 31

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

U SER I NTERFACE P ORTS

  • The front panel houses the following user interface ports, top through bottom:
  • USB Port - This port is used to connect a USB device for software upgrades, configuration backup, and restoring data.
  • Modem Port - A built-in V.90 modem allows the user to remotely access the OA-740 through the RJ-11 port at speeds up to 56 Kbps.
  • Console Port - The RS232 serial interface allows the user to access the system console at 9600 baud.

OmniAccess 740

Figure 10Ports on the Front Panel

C OOLING U NIT

The cooling unit is integrated in the chassis. The cooling unit houses speed fan for efficient chassis cooling.

Hardware Overview · USB Modem Console

Page 32 of the Alcatel-Lucent IP Phone (740) user manual — V ALID S YSTEM C ONFIGURATION
Page 32 · click to enlarge
Page 32

S YSTEM S PECIFICATIONS

The tables below provide environmental, power, and physical specifications that are required for the smooth operation of your OA-740.

Table 15Environmental Specifications

Temperature, operating 0 to 45°C

Temperature, non-operating -25 to 70°C

Humidity, operating 10 - 90% (non-condensing)

Altitude, operating 10,000 ft

Altitude, non-operating 15,000 ft

Table 16Power Specifications

AC-input voltage range 100-240 Volts

AC-input current 3 AMP

Power Consumption 250 Watts

Table 17Physical Specifications

Dimensions (H x W x D) (1.73 x 17.5 x 17) in.

(4.4 x 44.5 x 43.2) cm.

Weight 26.4 lbs (12.8 kgs)

Height in Rack Units (RU) 1 Rack Unit (1 RU)

V ALID S YSTEM C ONFIGURATION

There should be at least one SE card installed in the OA-740.

Show 4 more labels / short text on this page
OmniAccess 740 Overview · Parameter Value · Parameter Value · Parameter Value
Page 33 of the Alcatel-Lucent IP Phone (740) user manual — C HAPTER 3
Page 33 · click to enlarge
Page 33

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

C HAPTER 3

I NSTALLING THE OmniAccess 740

This chapter guides you through the process of preparing your OmniAccess 740 (OA-740) for installation.

This chapter describes the equipment, tools, power, and site requirements for installing the OA-740. It contains the following sections:

  • Preparing for Installation
  • Installation Checklist
  • Safety Measures
  • Site Requirement Guidelines
  • Power Supply Overview
  • General Installation
  • Rack-Mounting the OA-740
  • Installing User Modules

Before installing your OA-740, you should consider the power and cabling requirements that must be in place at your installation site. Other factors to consider would be the environmental conditions; the installation site should maintain normal and safe operation of the system.

PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 34 of the Alcatel-Lucent IP Phone (740) user manual — I NSTALLATION C HECKLIST
Page 34 · click to enlarge
Page 34

Installing the OmniAccess 740

P REPARING FOR I NSTALLATION

The OA-740 is shipped with all the user modules installed in the chassis. However, optional modules may be shipped in a separate package from the main system.

If you wish to install the components on your own, you need to understand the proper installation procedure and the safety guidelines involved in performing the same.

If you notice any deviations in the contents received as against the order, contact Alcatel-Lucent Technical Support immediately.

R EQUIRED T OOLS AND E QUIPMENT

  • You need the following items to install the OA-740:
  • ESD-preventive wrist strap
  • Antistatic mat
  • No. 2 Phillips screwdriver
  • 1/4-in. flat-blade screwdriver
  • Tape measure (optional)
  • Level (optional)
  • A total of 12 M5 x 10-mm Phillips flathead screws to secure the brackets to the chassis
  • A total of 16 slotted 10-32 x 3/8 screws for rack installation

I NSTALLATION C HECKLIST

To achieve a successful hardware installation, use the following checklist as a guideline before commencing with the installation.

1. Unpack the system.

Open the carton the right way up, and carefully remove contents in the package. Carefully remove the chassis from the carton.

2. Verify the contents of the package.

Verify that the contents are included in the shipping container (the accessories box might be separate):

  • One OA-740, fully assembled
  • One or more accessories boxes (some or all may be shipped separately)
Page 35 of the Alcatel-Lucent IP Phone (740) user manual — P REVENTING I NJURY
Page 35 · click to enlarge
Page 35

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

3. Verify the cards installed.

Verify that the line cards installed in your OA-740 match the card types on the packing list.

4. Have the tools to mount the chassis on the rack.

Keep tools, such as power screw-drivers, screws, cable guides/ties, etc., ready with you for mounting the chassis on the rack.

S AFETY M EASURES

The sections below describe the safety instructions to be followed while using the OA-740.

P REVENTING I NJURY

the OA-740.

  • Follow the guidelines given below to avoid injury while working with the OA-740:
  • To avoid injury, be careful when lifting the chassis out of the shipping box.
  • Never attempt to rack mount the OA-740 chassis unaided. Ask an assistant to help you for holding the chassis.
  • Never operate the OA-740 with exposed power-supply units.
  • Never operate the OA-740 if the chassis becomes wet or the area where the chassis installed is wet.

Safety Measures

Page 36 of the Alcatel-Lucent IP Phone (740) user manual — E QUIPMENT G UIDELINES
Page 36 · click to enlarge
Page 36

Installing the OmniAccess 740

E QUIPMENT G UIDELINES

The following guidelines will help to ensure your safety and protect the equipment. This list does not cover all potentially hazardous situations. However, Alcatel-Lucent advices you to observe caution while working with the system.

this section and identified within instructions of this document.

personnel.

  • The OA-740 is in compliance with national and local electrical codes.
  • Review the safety warnings before installing, configuring, or maintaining the OA-740.
  • Keep the system area clean and dust-free during and after installation.
  • Keep tools and rack shelf components away from walk areas.
  • Do not wear loose clothing, jewelry, or other items that could get caught in the rack/shelf. Fasten your tie or scarf and sleeves.
  • The equipment grounding should be in accordance with local and national electrical codes.
  • Input and earth wiring must be provided at the installation site and protected in accordance with local and national wiring regulations.
  • The OA-740 operates safely when it is used in accordance with its marked electrical ratings and product usage instructions.
Page 37 of the Alcatel-Lucent IP Phone (740) user manual — S AFETY WITH E LECTRICITY
Page 37 · click to enlarge
Page 37

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

L IFTING S AFELY

A fully configured OA-740 weighs approximately 26.4 lbs (12.8 kgs). Whenever you lift any heavy object, follow the below guidelines:

  • Ensure that the system is powered OFF.
  • Disconnect all external cables before lifting or moving.
  • Do not attempt to lift the equipment by yourself; have someone to assist you.
  • Ensure that your footing is solid, and balance the weight of the object between your feet.
  • Lift the system slowly; never move suddenly or twist your body as you lift.
  • Lift the chassis from the bottom; grasp the underside of the chassis exterior with both hands.

S AFETY WITH E LECTRICITY

Alcatel-Lucent advices you to follow the guidelines given below as a measure of safety.

supply cards.

presents no threat, harm, or non-compliance to operating staff or property. Verify that the unit is grounded properly and protected from voltage surges and static charges.

  • Follow these basic guidelines when working with any electrical equipment:
  • Disconnect all power cables and external cables before installing or removing the OA-740.
  • Do not work alone when potentially hazardous conditions exist.
  • Never assume that power has been disconnected from a circuit; always check.
  • Do not perform any action that creates a potential hazard to people or that makes the equipment unsafe.
  • Never install/work with equipment that appears damaged.
  • Carefully examine your work area for possible hazards, such as moist floors, ungrounded power extension cables, and missing safety grounds.

Safety Measures

Page 38 of the Alcatel-Lucent IP Phone (740) user manual — P REVENTING E LECTROSTATIC D ISCHARGE D AMAGE
Page 38 · click to enlarge
Page 38

Installing the OmniAccess 740

blasting caps or in an explosive environment unless the unit has been modified especially to be qualified for such use.

  • In addition, use these appropriate guidelines while working with any equipment that is disconnected from a power source, but still connected to the telephone wiring or other network cabling:
  • Never install or remove telephone wiring during a lightning storm.
  • Never install or remove telephone jacks in wet locations unless the jack is specifically designed for wet locations.
  • Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
  • Use caution when installing or modifying telephone lines.

P REVENTING E LECTROSTATIC D ISCHARGE D AMAGE

Electrostatic Discharge (ESD) damage, which occurs when electronic cards or components are improperly handled can result in complete or intermittent system failures. The line cards consist of printed circuit boards with Integrated Circuits (IC) and should be handled at edges or faceplate only.

prevent accidental removal, provide proper grounding for the system, and help to ensure that the cards are properly fitted in the shelf.

  • Follow the guidelines given below for preventing ESD damage:
  • Always use an ESD wrist strap or ankle strap and ensure that it makes good skin contact and is properly grounded.
  • Do not touch the printed circuit board, and avoid contact between the printed circuit board and your clothing.
  • Ensure the line cards are fully inserted in their respective chassis slots and the thumb screws are tightened.

measurement should be in 1 and 10 mega ohms range.

Page 39 of the Alcatel-Lucent IP Phone (740) user manual — S ITE R EQUIREMENT G UIDELINES
Page 39 · click to enlarge
Page 39

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

S ITE R EQUIREMENT G UIDELINES

The guidelines in this section help you to maintain and protect your OA-740 and its components from potential damage from over-voltage, extreme temperature conditions, and other adverse conditions. To assure normal operation and avoid unnecessary maintenance, plan your site configuration and prepare your site before installing the OA-740.

  • Follow these general precautions when planning your equipment locations and connections:
  • Make sure that the site maintains an ambient temperature between 15°C and 25°C, and keep the area around the system to be clean and dust-free.
  • Ensure that the cooling vents are not blocked and there is adequate air flow due to ample clearances around the OA-740.
  • Alcatel-Lucent recommends keeping the OA-740 off the floor and out of any area that tends to collect dust.
  • Follow ESD prevention procedures to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure.

The table below lists the operating and non-operating environmental site requirements. The ranges listed are those within which the OA-740 will continue to operate; however, a measurement that is approaching the minimum or maximum of a range indicates a potential problem. You can maintain normal operation by anticipating and correcting environmental anomalies before they approach minimum or maximum operating range.

Table 18Environmental Site Requirements

Temperature, operating 0°C 45°C

Temperature, non-operating –25°C 70°C

Humidity (non-condensing), operating 10% 90%

Altitude, operating Sea level 10,000 ft. (3048 m)

Altitude, non-operating Sea level 15,000 ft. (4572 m)

Clearance, air intake, and exhaust 20 inches (50.8 cm) —

Site Requirement Guidelines · Specification Minimum Maximum

Page 40 of the Alcatel-Lucent IP Phone (740) user manual — P OWER S UPPLY S PECIFICATIONS
Page 40 · click to enlarge
Page 40

Installing the OmniAccess 740

P OWER S UPPLY O VERVIEW

The following sections provide power supply requirements for the OA-740.

P OWER S UPPLY S PECIFICATIONS

The OA-740 requires 100/240V and 5A (RMS) @115V, 3A (RMS) @230V AC power. A fully loaded OA-740 consumes less than 250W of power.

For more details on power supply specifications, see “AC Power Specifications”.

The following section provides the procedure for connecting input power to your OA-740.

Page 41 of the Alcatel-Lucent IP Phone (740) user manual — C ONNECTING AC I NPUT P OWER
Page 41 · click to enlarge
Page 41

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

C ONNECTING AC I NPUT P OWER

disconnected last.

Alcatel-Lucent IP Phone (740) — C ONNECTING AC I NPUT P OWER diagram (page 41)
Fig. 4
Figure 11Connecting Power Cord
  • Use the specified power cord to power your system.
  • Connect the system end of the connector to the OA-740, as shown in above figure.
  • Connect the power plug to the utility power socket.
  • Be sure that the power cable is not left in a hazardous position that may restrict movement of personnel or that may fray due to movement of other equipment near the system.

Power Supply Overview

Page 42 of the Alcatel-Lucent IP Phone (740) user manual — I NTERFERENCE C ONSIDERATIONS
Page 42 · click to enlarge
Page 42

Installing the OmniAccess 740

P LANT W IRING

The following are guidelines for setting up the plant wiring and cabling at your site. When planning the location of the new system, consider the distance limitations for signaling, Electromagnetic Interference (EMI), and connector compatibility, as described in the sections below:

I NTERFERENCE C ONSIDERATIONS

  • Interference can occur when wires are run for any significant distance in an electromagnetic field. To prevent damages caused by interference, do the following:
  • Ensure that there is no radio interference emanating from the plant wiring.
  • Ensure that there is no electrical hazard by conducting power surges through lines and into equipment caused by EMI.
  • Use a high-quality twisted-pair cable with one ground conductor for each data signal, when applicable.
  • Give special consideration to the effect of a lightning strike near the system location. The electromagnetic pulse caused by lightning or other high-energy phenomena can destroy electronic devices.

DISTANCE LIMITATIONS AND INTERFACE SPECIFICATIONS

The size of your network and the distances between connections depend on the signal type, speed, and transmission media. For example, standard coaxial cable has a greater channel capacity than twisted-pair cable.

  • When preparing your site for network connections to the OA-740, you should consider the following:
  • Type of cabling required (fiber, shielded twisted-pair, or unshielded twisted-pair).
  • Distance limitations.
  • Cables needed for interface connections.
  • Any additional interface equipment required, such as transceivers, hubs, switches, modems, etc.

PRECAUTIONS TO BE TAKEN WHILE FIXING POWER CABLES

  • Follow these precautions and recommendations when planning power connections to the OA-740:
  • Check the power at your site before installation and periodically after installation to ensure that you are receiving uninterrupted power.
  • Install a power conditioner if necessary.
  • Install proper grounding to avoid damage from lightning and power surges.
Page 43 of the Alcatel-Lucent IP Phone (740) user manual — G ENERAL I NSTALLATION
Page 43 · click to enlarge
Page 43

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

G ENERAL I NSTALLATION

Planning a proper location for the OA-740 and the layout of your equipment rack or wiring cabinet are essential for successful operation of the system. Equipment placed too close together or inadequately ventilated can cause system over- temperature conditions, which may lead to system failure. Follow the precautions given below to avoid problems during installation and ongoing operation.

The OA-740 should be installed as per guidelines provided in the “Site Requirement Guidelines” section of this document. Please follow the guidelines in choosing a suitable and safe location.

  • When installing the system, ensure that the location is clean and safe, and that you have considered the following:
  • The OA-740 requires at least 3 inches of clearance on the right and left sides.
  • The OA-740 should be installed off the floor. (Excessive dust inside the system can cause over-temperature conditions and component failures.)
  • There must be approximately 20 inches (50.8 cm) of clearance at the front and rear of the OA-740 for installing and replacing the system units, or accessing network cables or equipment.
  • Line card and power supply filler panels are installed.
  • The OA-740 receives adequate ventilation (it should not be installed in an enclosed cabinet where ventilation is inadequate).
  • Adequate ground (earth) connection for your OA-740 is provided.

General Installation

Page 44 of the Alcatel-Lucent IP Phone (740) user manual — R ACK -M OUNTING THE OA-740
Page 44 · click to enlarge
Page 44

Installing the OmniAccess 740

R ACK -M OUNTING THE OA-740

The OA-740 is mounted on a standard 19-inch equipment rack. To easily access the electrical cables while the system is installed in a rack, ensure that you have easy access to the front and rear of the system, and that there is about 20-inch clearance at the front and rear of the rack.

You can also mount the OA-740 on an equipment shelf provided that the rack dimensions allow you to secure the system to the shelf. However, Alcatel-Lucent recommends rack-mounting the OA-740.

  • To rack-mount the OA-740, consider the following guidelines:
  • Maximum recommended operating temperature The maximum recommended operating temperature for the OA-740, indoor is 45°C. Determine a suitable operating environment based on this recommendation.
  • Elevated operating ambient temperature If the unit is installed in a closed or multi-unit rack assembly, the operating temperature of the rack environment may be greater than the ambient temperature of the room. Keep this in mind when installing the OA-740.
  • Reduced Airflow Install the OA-740 shelf in the rack so that the amount of airflow required for safe operation of the equipment in not compromised.
  • Mechanical Loading Mount the OA-740 in the rack so as to avoid a potentially hazardous condition due to uneven mechanical loading.
  • Circuit Overloading When you connect the OA-740 to the supply circuit, consider the effect that overloading of the circuits might have on over current protection and supply wiring.
  • Reliable Grounding Maintain reliable grounding for the OA-740 and all rack-mounted equipment, giving particular attention to supply circuits.
Page 45 of the Alcatel-Lucent IP Phone (740) user manual — P ARTS R EQUIRED
Page 45 · click to enlarge
Page 45

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

P ARTS R EQUIRED

  • The following tools and parts are required to rack-mount the OA-740:
  • AC power supply unit
  • One 6-gauge ground cable
  • Two hex nuts and M4 screws
  • Four 10-32 x 3/8-inch slotted screws
  • 3/8-inch nut driver
  • No. 2 Phillips screwdriver
  • 1/4-inch flat-blade screwdriver
  • Cable ties, if necessary

Rack-Mounting the OA-740

Page 46 of the Alcatel-Lucent IP Phone (740) user manual — I NSTALLING THE OA-740 IN THE R ACK
Page 46 · click to enlarge
Page 46

Installing the OmniAccess 740

I NSTALLING THE OA-740 IN THE R ACK

chassis in the rack unassisted.

before installing the OA-740 in the rack.

To install the OA-740 chassis in the rack, complete the following steps:

1. Ensure that the rack is stable, and verify that your path to the rack is unobstructed.
2. Ensure that the rack mount brackets are in the same level.
3. Position the OA-740 chassis in front of the rack.
4. Lift the OA-740 by the side of chassis, and slide the chassis into the rack. Push it back until the brackets meet the mounting strips or posts on both sides of the equipment rack. When the chassis is slid back all the way, make one or two people hold the chassis in place.
5. Insert the slotted screws (two screws per bracket) through the brackets and into the mounting strip. Tighten all the screws.
Alcatel-Lucent IP Phone (740) — I NSTALLING THE OA-740 IN THE R ACK diagram (page 46)
Fig. 5
Figure 12Rack Mounting the OA-740
Page 47 of the Alcatel-Lucent IP Phone (740) user manual — I NSTALLING L INE C ARDS
Page 47 · click to enlarge
Page 47

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

I NSTALLING U SER M ODULES

The following sections describe the procedure to install the user modules in your OA-740.

I NSTALLING L INE C ARDS

Follow the procedure detailed below to install the line cards.

pins.

1. Insert the line cards in their respective slots (0, 1, 2, 3).

By default, SE card is installed in slots 2, 3. The other line cards can be installed in slots 0, 1.

2. Verify that the line card is rested on the guide and it rides smoothly in the slot.
3. Push the line card firmly and ensure that the card is fully inserted in its respective slot and tighten the thumb screws.
Alcatel-Lucent IP Phone (740) — I NSTALLING L INE C ARDS diagram (page 47)
Fig. 6
Figure 13Installing Services Engine

Installing User Modules

Page 48 of the Alcatel-Lucent IP Phone (740) user manual — R EMOVING F ILLERS
Page 48 · click to enlarge
Page 48

Installing the OmniAccess 740

Alcatel-Lucent IP Phone (740) — Installing Fillers diagram (page 48)
Fig. 7 · Installing Fillers
Figure 14Installing Line Card

R EMOVING THE L INE C ARDS

To remove the line card, loosen the thumb screws provided on the line card and pull the line card out of the slot.

I NSTALLING F ILLERS

Fillers are used to cover unused slots. The procedure to install different types of fillers is outlined below.

1. Insert the filler in the empty slot.
2. Verify that the filler is rested on the guide and rides smoothly in the slot.
3. Push the filler firmly and ensure that the filler is fully inserted in its respective slot and tighten the screws.

R EMOVING F ILLERS

To remove the filler for the line card slots, loosen the thumb screws provided on the line card and pull the filler out of the slot.

Page 49 of the Alcatel-Lucent IP Phone (740) user manual — C HAPTER 4
Page 49 · click to enlarge
Page 49

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

C HAPTER 4

S TARTING THE OmniAccess 740

I NTRODUCTION

This chapter explains the procedure for starting the OmniAccess 740 (OA-740), and connecting to the system console port for Command Line Interface (CLI) access for performing basic configuration tasks.

  • Checking Conditions Prior to System Startup
  • Starting the OA-740
  • Connecting to the System Console Port
  • Performing Basic Configuration Tasks
  • Connecting the System to the Network
  • Site Log
PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 50 of the Alcatel-Lucent IP Phone (740) user manual — S TARTING THE OA-740
Page 50 · click to enlarge
Page 50

Starting the OmniAccess 740

C HECKING C ONDITIONS P RIOR TO S YSTEM S TARTUP

Before you power ON the OA-740, check the following:

1. Ensure that the utility power cable is connected to a valid power cord in the rear panel, and power is available from this source.
2. Ensure that the SE is correctly and securely installed.
3. Ensure that a PC or VT100 terminal is connected to the console port, using the appropriate console cable. (If the system is not connected to a console, see the “Connecting to the System Console Port” section of this document to connect the system to a console.)

S TARTING THE OA-740

After installing the OA-740 and connecting the cables, follow the procedure given below to start the system:

1. Power ON the OA-740.

Power on the OA-740 by turning on the external power switch located near the power cord on the rear panel. If power supply is available, you can hear the rotation of system fans, and the system begins the bootup sequence.

2. Monitor the system for various bootup messages.

Once the system begins to startup, monitor the SE LEDs for various stages of the booting process.

The following table shows the state of SE LEDs after startup.

Table 19LED Status

Active Off Power up status. This is the default display when the system is first powered on and before the software is loaded.

Green SE card is active.

LED Status Description · SE LEDs

Page 51 of the Alcatel-Lucent IP Phone (740) user manual — Checking Conditions Prior to System Startup
Page 51 · click to enlarge
Page 51

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

3. Configure the system.

Once the system bootup is complete, the system enters the initial configuration setup mode, which is an interactive mode for configuring the system. Follow the prompts on the screen to input the required information.

For further customizing and changing the configuration, it would be necessary to use the full-fledged CLI access to the system. To use the CLI and to know more about its usage, refer to the “OmniAccess 700 CLI Configuration Guide”.

4. If all the activities have proceeded normally and if the initial configuration is complete, the OA-740 is installed and is now ready for deployment in your network.

Starting the OA-740

Page 52 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740
Page 52 · click to enlarge
Page 52

Starting the OmniAccess 740

C ONNECTING TO THE S YSTEM C ONSOLE P ORT

The OA-740 has a RJ-45 console port connector. A RJ-45 - RJ-45 “roll-over” cable along with RJ-45 to DB-9 (female) adapter is provided with the system to access the console port via a DTE (computer/terminal). Refer to “Pin Connector Details for OmniAccess 740” for detailed information on cable pin connection.

To connect the OA-740 to the console, perform the following steps:

1. Connect the RJ-45 end of the console cable to the front-panel console port on the OA-740 and the DB-9 end to the serial-port (COM) on your computer/ terminal.

OmniAccess 740

Figure 15Connecting to the System Console

USB Modem Console · RJ-45 Connector · RJ-45 Console Port

Page 53 of the Alcatel-Lucent IP Phone (740) user manual — Connecting to the System Console Port
Page 53 · click to enlarge
Page 53

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Connecting to the System Console Port

2. Start your terminal emulation software.

Example: kermit or hyperterm terminal (if you are using Microsoft Windows operating system) or minicom terminal (if you are using Unix/Linux operating system).

3. Set the console session as follows:
Table 20Console Properties
4. Watch for console message output or press the Enter key to get the device prompt.
Show 6 more labels / short text on this page
Parameter Value · Baud rate 9600 · Parity None · Data Bits 8 · Stop Bit 1 · Flow control None
Page 54 of the Alcatel-Lucent IP Phone (740) user manual — ALU>
Page 54 · click to enlarge
Page 54

Starting the OmniAccess 740

P ERFORMING B ASIC C ONFIGURATION T ASKS

Once you boot the OA-740 and connect to the console, you can start configuring your OA-740 either through the CLI or the web-based Graphical User Interface (GUI).

A CCESSING OA-740 T HROUGH CLI

The CLI is the primary interface to access the OA-740 through the console. The CLI allows you to configure, monitor, and troubleshoot the system, and enables network connectivity.

To perform initial configuration of your system, follow the procedure given below:

1. Once the system bootup is complete, you are asked to configure the password for a special user - superadmin . Superadmin is authorized to execute any command. You need to set the superadmin password when the following prompt is displayed:

Enter the new password for superadmin:

Once you enter the password for the superadmin, you will be asked to reconfirm the password, with the following prompt:

Retype the new password:

After confirming the password, you will be asked to login using a username. The below prompt appears.

Username:

Enter the user name as superadmin. Now, you will be prompted for a password.

Password:

Enter the newly configured superadmin password.

2. After entering the correct user name and password, the ALU> prompt is displayed. If the prompt is not seen, press the Enter key a few times.

ALU>

By default, the host name is “ALU”. (To configure a different host name, use the configure “hostname ’ command in the Configuration mode.)

3. At the ALU prompt, enter the enable command to enter the Super User Mode (SUM).

Example:

ALU> enable ALU#

Page 55 of the Alcatel-Lucent IP Phone (740) user manual — Performing Basic Configuration Tasks
Page 55 · click to enlarge
Page 55

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Performing Basic Configuration Tasks

4. From SUM , you can enter the Configuration Mode (CM). The CM is used to configure the system globally, to enter specific configuration modes or to configure specific elements, such as interfaces or protocols.

Enter the configure terminal command to enter the Configuration mode.

Example:

ALU# configure terminal ALU(config)#

The above steps are enough to configure the OA-740 via console.

5. To configure the system remotely (Telnet, SSH, and Modem), you need to configure basic Authentication, Authorization, and Accounting (AAA) configuration. AAA is a system in IP-based networking to control which users have access to the system, what resources users have access to, and to keep track of the activity of users over a network.

To enable AAA services on your system, enter the aaa services command in the Configuration mode.

Example:

6. Set the enable password (system password). To set the system password, enter the following command:

enable {secret|password} [5] <password>

Example:

ALU(config)# enable secret test Secret for level 15 is set

ALU(config)# aaa services

Page 56 of the Alcatel-Lucent IP Phone (740) user manual — Performing Basic Configuration Tasks
Page 56 · click to enlarge
Page 56

Starting the OmniAccess 740

7. Establish authentication for new users by configuring new user accounts. To configure a new user account, use the following command:

username <user-name> {password [5] <password>|nopassword| secret [5] <password>}

Example:

ALU(config)# username user1 password pass1

8. Configuring an interface. Enter the following command to enter the Interface Configuration mode.

interface <name> <slot/port>

Example:

ALU(config)# interface GigabitEthernet 7/0 ALU(config-interfaceGigabitEthernet7/0)#

(For more information on configuring interfaces, refer to the ‘The Command Line Interface’ chapter in the OmniAccess 700 CLI Configuration Guide.)

9. Administratively bring up the interface by using the ‘ no shutdown ’ command:

Example:

ALU(config-if GigabitEthernet7/0)# no shutdown

10. Configure an IP address for the interface by entering the following command. Enter the IP address in the valid IP address format A.B.C.D.

ip address {<ip-address subnet-mask>|<ip-address/prefix- length>}

Example:

ALU(config-if GigabitEthernet7/0)# ip address 192.168.1.1/24

11. Enable SSH and Telnet for in-band Management. The following command enables SSH/Telnet connection to a remote computer: • Secure Shell (ssh) is a program for logging in to a remote machine that provides secure communication between two systems.

ssh {enable|disable}

Example:

  • Telnet is a user command and an underlying TCP/IP protocol for accessing remote computers. Telnet is a program that enables connection to foreign or remote host computers, and provides access to information on them.

telnet {enable|disable}

Example:

ALU(config)# ssh enable · ALU(config)# telnet enable

Page 57 of the Alcatel-Lucent IP Phone (740) user manual — Performing Basic Configuration Tasks
Page 57 · click to enlarge
Page 57

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Performing Basic Configuration Tasks

12. Enable HTTP & HTTPS for web-based management. • HTTP is the primary protocol used for the transfer of files over the World Wide Web. You can access the OA-700 using HTTP through a web browser after being authenticated.

http {enable|disable}

Example:

ALU(config)# http enable • HTTPS, in addition to the normal HTTP uses SSL encryption for secure transmission of files.

Example:

13. Enable Modem for Out of Band Management.

modem {enable|disable}

Example:

14. Show Chassis - The ‘ show chassis ’ command provides a physical inventory of the running chassis components for a specific slot or for the entire system.

Example: ALU> show chassis Physical inventory at Tue Oct 30 12:31:50 2007 System started approximately Tue Oct 30 12:30:32 2007 Uptime is 0 days 0 hours 3 minutes 40 seconds T1E1 - Four port T1E1 (active) Slot number: 0 Part number: 902604-90 Manufacturer: ALU Description: Four port T1E1 Serial number: ND0533001165 Version: 00 Revision: 55 Deviation: 0000 Loader version: 2.29 ALU-OS version: 2.2.57 SE - Service engine (active) Slot number: 3 Part number: 902601-90 Manufacturer: ALU Description: Service engine Serial number: DD0538002041 Version: 01 Revision: 02 Deviation: 0001 Opteron CPU Version: 10 Opteron CPU Frequency: 1994 MHz LoL firmware version: 2.2.56 Loader version: 2.29

ALU(config)# https enable · ALU(config)# modem enable

Page 58 of the Alcatel-Lucent IP Phone (740) user manual — Performing Basic Configuration Tasks
Page 58 · click to enlarge
Page 58

Starting the OmniAccess 740

ALU-OS version: 2.2.57 MDC Serial number: WL0534000130 Deviation: 0002 Revision: A1 Version: 01 BP - ALU OA740 chassis (passive) Slot number: 29 Part number: 902610-90 Manufacturer: ALU Description: ALU OA740 chassis Serial number: WL0537000210 Version: 00 Revision: 01 Deviation: 0001 Base MAC: 00:11:8b:00:70:00 ALU#

15. Save the running configuration to the startup configuration.

Example:

For further configuration of your OA-740, refer to the OmniAccess 700 CLI Configuration Guide provided in the OA-740 Documentation CD along with your system.

ALU(config)# write mem

Page 59 of the Alcatel-Lucent IP Phone (740) user manual — A CCESSING OA-740 T HROUGH GUI
Page 59 · click to enlarge
Page 59

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Connecting the System to the Network

C ONNECTING THE S YSTEM TO THE N ETWORK

This section details the procedure to connect to your OA-740 through the internal or external network.

C ONNECTING TO I NTERNAL N ETWORK

  • To access the OA-740 through hosts in internal network/LAN, you can use the following:
  • Accessing OA-740 Through GUI
  • Connecting Through Telnet
  • Connecting Through SSH

A CCESSING OA-740 T HROUGH GUI

Follow the procedure given below to access and configure the OA-740 through a GUI.

1. Configure IP address of an interface.

To configure an IP address of a given interface, follow the steps detailed in the “Accessing OA-740 Through CLI” section of this document.

2. Open a Web browser from your PC.
3. In the address bar/field, type the IP address of the interface and press the Enter key.

Example:

http://<ip address> http://192.168.1.1/24

The login page for the Web GUI is displayed in the browser window.

4. Enter the user name and password, and press the Enter key. This will launch a web interface to configure your OA-740.

For further configuration of your OA-740, refer to the OmniAccess 700 Web GUI User Guide provided in the OA-740 Documentation CD.

Page 60 of the Alcatel-Lucent IP Phone (740) user manual — OmniAccess 740
Page 60 · click to enlarge
Page 60

Starting the OmniAccess 740

C ONNECTING T HROUGH T ELNET

Telnet is a user command and an underlying TCP/IP protocol for accessing remote computers. Telnet allows you to log on as a regular user with preset privileges to the specific application and data on that remote computer.

OmniAccess 740

Figure 16Connecting to Internal Network

To establish a Telnet session with the OA-740, follow the procedure below:

1. Connect the RJ-45 cable from the Ethernet port in the SE card on the front panel of the OA-740 to the internal router, switch, or hub in your LAN.
  • Step 2: Open a Telnet session, for example, to 192.168.1.1 .
  • From the Windows host, click Start > Run , type telnet 192.168.1.1 , and click OK .
  • From the Unix/Linux host, from the terminal window, type telnet 192.168.1.1 and press the Enter key.
3. Enter the username and password at the prompt.

You are now ready to access the OA-740, using a Telnet session.

USB Modem Console

Page 61 of the Alcatel-Lucent IP Phone (740) user manual — C ONNECTING T HROUGH SSH
Page 61 · click to enlarge
Page 61

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Connecting the System to the Network

C ONNECTING T HROUGH SSH

Secure Shell (SSH) is a Unix-based command interface and protocol for securely getting access to a remote computer. SSH uses the RSA public key cryptography for both connection and authentication.

To establish an SSH session with the OA-740, follow the procedure below:

1. Connect the RJ-45 cable from the Ethernet port in SE card on the front panel of the OA-740 to the router, switch, or hub in your internal network/LAN.
2. Open an SSH session, for example, to 192.168.1.1 .

From the Unix/Linux host, from the terminal window, type ssh <username>@192.168.1.1, and press the Enter key.

3. Enter the username and password at the prompt.

You are now ready to access the OA-740 using an SSH session.

Page 62 of the Alcatel-Lucent IP Phone (740) user manual — C ONNECTING T HROUGH E XTERNAL N ETWORK
Page 62 · click to enlarge
Page 62

Starting the OmniAccess 740

C ONNECTING T HROUGH E XTERNAL N ETWORK

To establish a link between the OA-740 and the external network (WAN/Internet), connect the RJ-11 jack from the external modem to the modem port provided in the front panel of the OA-740.

Figure 17Connecting through External Network

USB Modem Console · RJ-11 RJ-11 Connector · Modem Port

Page 63 of the Alcatel-Lucent IP Phone (740) user manual — S ITE L OG
Page 63 · click to enlarge
Page 63

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

S ITE L OG

It is a good practice to maintain a log of the OA-740 to track all activities related to the system. This information also provides valuable history and service record for service personnel. Keep your site log in a common place, near the rack shelf where anyone who performs tasks has access to it.

  • Site log entries might include the following:
  • Installation progress - Make a copy of the System Installation Checklist and insert it into the site log. Make entries in the Installation Checklist as each procedure is completed.
  • Upgrades and removal/replacement procedures - Use the site log as a record of system maintenance and expansion history. Each time a procedure is performed on the system, update the site log to reflect the following:
  • Any line card removed and replaced
  • Power supply removals and changes
  • Configuration changes
  • Software upgrades
  • Corrective maintenance procedures performed
  • Related comments.

Site Log

Page 64 of the Alcatel-Lucent IP Phone (740) user manual — Site Log
Page 64 · click to enlarge
Page 64

Starting the OmniAccess 740

Page 65 of the Alcatel-Lucent IP Phone (740) user manual — D ECLARATION OF C ONFORMITY : CE M ARK
Page 65 · click to enlarge
Page 65

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

Appendix A

Regulatory Compliance and Safety Information

This appendix provides information on regulatory agency compliance and safety for the OmniAccess 740 (OA-740).

D ECLARATION OF C ONFORMITY : CE M ARK

This equipment is in compliance with the essential requirements and other provisions of Directive 73/23/EEC and 89/336/EEC as amended by Directive 93/ 68/EEC.

Français: Ce matériel est conformément aux conditions essentielles et à d'autres dispositions de 73/23/EEC et de 89/336/EEC directifs comme modifié par Directive 93/68/EEC.

Deutsch: Konformitätserklärung: CE Kennzeichnung Diese Anlage ist gemäß den wesentlichen Anforderungen und anderen Bestimmungen richtungweisenden 73/23/EEC und des 89/336/EEC, wie von Directive 93/68/EEC geändert.

Español: Este directivo equipo está en conformidad con los requisitos esenciales y otras provisiones 73/23/EEC y 89/336/EEC según la enmienda prevista por Directive 93/68/EEC.

PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 66 of the Alcatel-Lucent IP Phone (740) user manual — W ASTE E LECTRICAL AND E LECTRONIC E QUIPMENT (WEEE) S TATEMENT
Page 66 · click to enlarge
Page 66

Regulatory Compliance and Safety Information

W ASTE E LECTRICAL AND E LECTRONIC E QUIPMENT (WEEE) S TATEMENT

The product at end of life is subject to separate collection and treatment in the EU Member States, Norway and Switzerland and therefore marked with the symbol:

Treatment applied at end of life of the product in these countries shall comply with the applicable national laws implementing directive 2002/96EC on waste electrical and electronic equipment (WEEE).

Page 67 of the Alcatel-Lucent IP Phone (740) user manual — 六价铬
Page 67 · click to enlarge
Page 67

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

China RoHSHazardous Substance Table

C HINA R O HS: H AZARDOUS S UBSTANCE T ABLE

产品说明书附件 SUPPLEMENT TO PRODUCT INSTRUCTIONS

这个文件涉及的是在中华人民共和国境内进口或销售的电子信息产品 Include this document with all Electronic Information Products imported

or sold in the People’s Republic of China

有毒有害物质或元素 (Hazardous Substance) 部件名称

六价铬

6+ ) 多溴联苯

多溴二苯醚

(PBB)

(PBDE)

电路模块 (Circuit Modules) × ○

电缆及电缆组件 (Cables & Cable Assemblies) × ○

金属部件 (Metal Parts) × ○

塑料和聚合物部件 (Plastic and Polymeric parts) ○

对于交付时集成了电池的电子信息产品 For electronic information products delivered with integrated functional batteries:

电池 (Batteries) ○

○: 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。 Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. ×: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求。 Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. 对销售之日的所售产品,本表显示, 阿尔卡特朗讯公司供应链的电子信息产品可能包含这些物质。注意:在所售产 品中可能会也可能不会含有所有所列的部件。

This table shows where these substances may be found in the supply chain of Alcatel-Lucent electronic

information products, as of the date of sale of the enclosed product. Note that some of the component

types listed above may or may not be a part of the enclosed product.

除非另外特别的标注,此标志为针对所涉及产品的环保使用期标志. 某些零部件会有 一个不同的环保使用期(例如,电池单元模块)贴在其产品上. 此环保使用期限只适用于产品是在产品手册中所规定的条件下工作. The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here, unless otherwise marked. Certain parts may have a different EFUP (for example, battery modules) and so are marked to reflect such. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.

Show 4 more labels / short text on this page
(Parts) 铅 (Pb) · 汞 (Hg) · 镉 (Cd) · (Cr
Page 68 of the Alcatel-Lucent IP Phone (740) user manual — CB FB
Page 68 · click to enlarge
Page 68

Regulatory Compliance and Safety Information

Products are packaged using one or more of the following packaging materials:

Alcatel-Lucent IP Phone (740) — China RoHS: Hazardous Substance Table diagram (page 68)
Fig. 8 · China RoHS: Hazardous Substance Table
Alcatel-Lucent IP Phone (740) — China RoHS: Hazardous Substance Table diagram (page 68)
Fig. 9 · China RoHS: Hazardous Substance Table

CB FB

Corrugated Cardboard Corrugated Fiberboard Low-Density Polyethylene

Page 69 of the Alcatel-Lucent IP Phone (740) user manual — T ELECOM
Page 69 · click to enlarge
Page 69

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

S TANDARDS C OMPLIANCE

The product bears the CE mark. In addition it is in compliance with the following other safety and EMC standards:

All hardware switching modules used in the OA-740 comply with Class A standards. Modules with copper connectors meet Class A requirements using unshielded (UTP) cables.

S AFETY

  • UL60950-1:2003
  • CSA 22.2 No. 60950-1:2003
  • EN 60950
  • IEC 60950-1:2001

EMC

  • FCC Part 15, Subpart B
  • ICES 003
  • EN 55022:1998/A1:2000
  • EN 55024
  • AS/NZS 3548:1995+A1:1997+A2:1997
  • VCCI V-3/2000.04

T ELECOM

  • 47, CFR Part 68 AND ACTA, Adopted Technical Criteria
  • CS 03 Issue 8, Part II
  • TBR 12 AND TBR 13
  • AS/ACTF S016: 2001
  • T1(DS1) JATE - 1.544 Mbit/sec Digital Interface
  • E1 JATE - 2.048 Mbit/sec Digital Interface

Standards Compliance

Page 70 of the Alcatel-Lucent IP Phone (740) user manual — ETSI TBR 012
Page 70 · click to enlarge
Page 70

Regulatory Compliance and Safety Information

D ECLARATION OF C ONFORMITY A DDENDUM

Application of Council Directive(s) 89/336/EEC

73/23/EEC

1999/5/EEC

Manufacturer’s Address 26801 West Agoura Road

Tel818-880-3500
Fax818-880-3505
Websitewww.alcatel-lucent.com

Conformance to Directive(s)/ Product Standards

EN 55022:1998+A1:2000+A2:2003

EN 61000-3-2:2000

EN 61000-3-3:1995+A1:2001

EN 55024:1998+A1:2001

EN 61000-4-2:2001

EN 61000-4-3:2002

EN 61000-4-4:1995+A1:2000+A2:2001

EN 61000-4-5:2001

EN 61000-4-6:2001

EN 61000-4-8:2001

EN 61000-4-11:2001

EN 55024:1998+A1:2001

EN60555-2: 1995

EN 60950-1:2001+A11

ETSI EN 300 386 v1.4.1(2000-2003)

ETSI TBR 012

ETSI TBR 013

Show 6 more labels / short text on this page
Manufacturer’s Name Alcatel-Lucent · Calabasas, CA 91301 · EC Directive 89/336/EEC · EC Directive 73/23/EEC · EC Directive 1999/5/EEC · CB Scheme
Page 71 of the Alcatel-Lucent IP Phone (740) user manual — FCC C LASS A, P ART 15
Page 71 · click to enlarge
Page 71

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

FCC C LASS A, P ART 15

This equipment has been tested and found to comply with the limits for Class A digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this guide, may cause interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense.

The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user’s authority to operate this equipment.It is suggested that the user use only shielded and grounded cables to ensure compliance with FCC Rules.

  • If this equipment does cause interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient the receiving antenna.
  • Relocate the equipment with respect to the receiver.
  • Move the equipment away from the receiver.
  • Plug the equipment into a different outlet so that equipment and receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.

Standards Compliance

Page 72 of the Alcatel-Lucent IP Phone (740) user manual — CISPR22 C LASS A WARNING
Page 72 · click to enlarge
Page 72

Regulatory Compliance and Safety Information

C ANADA C LASS A S TATEMENT

This equipment does not exceed Class A limits per radio noise emissions for digital apparatus, set out in the Radio Interference Regulation of the Canadian Department of Communications.

AVIS DE CONFORMITÈ AUX NORMES DU MINISTÈRE DES COMMUNICATIONS DU CANADA

Cet èquipement ne dèpasse pas les limites de Classe A d íèmission de bruits radioèlectriques pour les appareils numèriques,telles que prescrites par le RÈglement sur le brouillage radioèlectrique ètabli par le ministère des Communications du Canada.

JATE

This equipment meets the requirements of the Japan Approvals Institute of Telecommunications Equipment (JATE).

CISPR22 C LASS A WARNING

This is a Class A product. In a domestic environment, this product may cause radio interference. Under such circumstances, the user may be requested to take appropriate countermeasures.

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Alcatel-Lucent IP Phone (740) — CISPR22 C LASS A WARNING diagram (page 72)
Fig. 10
Page 73 of the Alcatel-Lucent IP Phone (740) user manual — Class A Warning for Taiwan and Other Chinese Markets
Page 73 · click to enlarge
Page 73

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

CLASS A WARNING FOR TAIWAN AND OTHER CHINESE MARKETS

This is a Class A Information Product. When used in a residential environment, it may cause radio frequency interference. Under such circumstances, the user may be requested to take appropriate countermeasure.

Alcatel-Lucent IP Phone (740) — Class A Warning for Taiwan and Other Chinese Markets diagram (page 73)
Fig. 11 · Class A Warning for Taiwan and Other Chinese Markets

Standards Compliance

Page 75 of the Alcatel-Lucent IP Phone (740) user manual — I NVISIBLE L ASER R ADIATION W ARNING
Page 75 · click to enlarge
Page 75

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

E LECTRICAL S TORM W ARNING

To avoid a shock hazard, do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

Français: Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.

Deutsch: Hinweise bei Unwetter Um elektrische Schläge zu vermeiden dürfen während eines Gewitters and diesem Gerät keine Kabel angeschlossen oder gelöst werden, sowie keinerlei Installationen, Wartungen oder Konfigurationen vorgenommen werden.

Español: Para evitar peligro de descargas, no conecte o desconecte ningun cable, ni realice ninguna instalación, maintenimiento o reconfiguración de este producto durante una tormenta eléctrica.

I NSTALLATION W ARNING

Only personnel knowledgeable in basic electrical and mechanical procedures should install or maintain this equipment.

Français: Toute installation ou remplacement de l'appareil doit être réalisée par du personnel qualifié et compétent.

Deutsch: Installationshinweise Dieses Gerät soll nur von Personal installiert oder gewartet werden, welches in elektrischen und mechanischen Grundlagen ausgebildet ist.

Español: Estos equipos deben ser instalados y atendidos exclusivamente por personal adecuadamente formado y capacitado en técnicas eléctricas y mecánicas.

I NVISIBLE L ASER R ADIATION W ARNING

Lasers emit invisible radiation from the aperture opening when no fiber-optic cable is connected. When removing cables do not stare into the open apertures. In addition, install protective aperture covers to fiber ports with no cable connected.

Français: Des radiations invisibles à l'œil nu pouvant traverser l'ouverture du port lorsque aucun câble en fibre optique n'y est connecté, il est recommandé de ne pas regarder fixement l'intérieur de ces ouvertures. Installez les caches connecteurs prévus à cet effet.

Deutsch: Hinweise zur unsichtbaren Laserstrahlung Die Laser strahlen an der Blendenöffnung unsichtbares Licht ab, wenn keine Glasfaserkabel angeschlossen sind. Blicken Sie nicht in die Öffnungen und installieren Sie unverzüglich die Abdeckungen über den Glasfaseranschlüssen.

Español: Debido a que la apertura del puerto puede emitir radiación invisible cuando no hay un cable de fibra conectado, procurar no mirar directamente a las aperturas para no exponerse a la radiación.

Translated Safety Warnings

Page 76 of the Alcatel-Lucent IP Phone (740) user manual — O PERATING V OLTAGE W ARNING
Page 76 · click to enlarge
Page 76

Regulatory Compliance and Safety Information

B ATTERY W ARNING

There is a danger of explosion if the battery in your chassis is incorrectly replaced. Replace the battery only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. The manufacturer’s instructions are as follows: Return the module with the battery to Alcatel-Lucent. The battery will be replaced at Alcatel-Lucent’s factory.

Français: Il y a un danger d'explosion si la batterie dans votre châssis est remplacée avec une autre ne correspondant pas aux préconisations constructeur. Il faut donc renvoyer le module en réparation chez Alcatel-Lucent qui se chargera de remplacer la batterie.

Deutsch: Hinweise Batterie Bei falschem Einsetzen der batterie in das Gerät besteht die Gefahr der Explosion. Bitte ersetzen Sie die Batterie nur durch den gleichen bzw. gleichwertigen Typ, empfohlen durch den Hersteller. Benutzte Batterien entsorgen sie bitte wie folgt: Bitte senden Sie das Modul zurück zu Alcatel-Lucent. Dort wird die gebrauchte Batterie ersetzt.

Español: Si substituye las pilas de litio en su chasis, siempre utilice el mismo modelo o el tipo equivalente de pila recomendada por el fabricante. Deshágase de las pilas usadas según las instrucciones del fabricante. Devuelva el módulo con la pila de litio a Alcatel-Lucent. La pila de litio será substituida en la fábrica de Alcatel-Lucent.

Dansk: ADVARSEL! batteri--Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske batteri af samme fabrikat og type. Lever det brugte batteri tilbage tilleverandoren.

O PERATING V OLTAGE W ARNING

To reduce the risk of electrical shock, keep your hands and fingers out of power supply bays and do not touch the backplane while the switch is operating.

Français: Pour réduire tout risque électrique, gardez vos mains et doigts hors des alimentations et ne touchez pas au fond de panier pendant que le commutateur fonctionne.

Deutsch: Hinweise gegen elektrischen Schlag Um die Gefahr des elektrischen Schlages zu verringern, greifen sie bitte nicht in die Spannungsversorgung und berühren sie nicht die Rückwandplatine während das Gerät arbeitet.

Español: Para reducir el riesgo de descargas eléctricas, no meta sus manos y dedos dentro del chasis de la fuente de alimentación y no toque componentes internos mientras que el interruptor está conectado.

Page 78 of the Alcatel-Lucent IP Phone (740) user manual — R ESTRICTED A CCESS L OCATION W ARNING
Page 78 · click to enlarge
Page 78

Regulatory Compliance and Safety Information

READ IMPORTANT SAFETY INFORMATION WARNING

The Getting Started Guide that accompanied this equipment contains important safety information about which you should be aware when working with hardware components in this system. You should read this guide before installing, using, or servicing this equipment.

Français: Avant de brancher le système sur la source d'alimentation, consultez les directives d'installation disponibles dans le “Getting Started Guide”.

Deutsch: Bitte lesen - Sicherheitshinweise Der Getting Started Guide, welcher diese Anlage beiliegt, enthält wichtige Sicherheitsinformationen, über die sie sich beim Arbeiten mit den Hardwareeinheiten bewußt sein sollten. Sie sollten diese Hinweise lesen, bevor sie installieren, reparieren oder die Anlage verwenden.

Español: La 'Getting Started Guide' que acompañó este equipo contiene información importante de seguridad sobre la cual usted debe estar enterado al trabajar con los componentes de dotación física en este sistema. Usted debe leer esta guía antes de instalar, usar o mantener este equipo.

R ESTRICTED A CCESS L OCATION W ARNING

This equipment should be installed in a location that restricts access. A restricted access location is one where access is secure and limited to service personnel who have a special key, or other means of security.

Français: Le matériel doit être installé dans un local avec accès limité ou seules les personnes habilitées peuvent entrer.

Deutsch: Hinweis zu Umgebungen mit beschränktem Zutritt Die Anlage sollte an einem Standort mit beschränktem Zutritt installiert sein. Ein Standort mit beschränktem Zutritt stellt sicher, daß dort nur Servicepersonal mit Hilfe eines Schlüssels oder eines anderen Sicherheitssystems Zugang hat.

Español: Este equipo se debe instalar en un sitio con acceso restrinjido. Un sitio con el acceso restrinjido es uno seguro y con acceso limitado al personal de servicio que tiene una clave especial u otros medios de seguridad.

Page 79 of the Alcatel-Lucent IP Phone (740) user manual — W RIST S TRAP W ARNING
Page 79 · click to enlarge
Page 79

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

W RIST S TRAP W ARNING

Because electrostatic discharge (ESD) can damage switch components, you must ground yourself properly before continuing with the hardware installation. For this purpose, Alcatel-Lucent provides a grounding wrist strap and a grounding lug located near the top-right of the chassis. For the grounding wrist strap to be effective in eliminating ESD, the power supplies must be installed in the chassis and plugged into grounded AC outlets.

Français: L'électricité statique (ESD) peut endommager les composants du commutateur. Pour cette raison Alcatel-Lucent joint à l'envoi du châssis un bracelet antistatique à brancher sur la prise mise à la terre située en bas à droite du commutateur. Vous devrez mettre ce bracelet avant toute intervention hardware.

Deutsch: Hinweise zur ESD (Elektrostatischen Aufladung) Weil elektrostatische Aufladung (ESD) Teile der Anlage beschädigen könnten, müssen sie sich selbst erden, bevor sie mit der Hardware Installation beginnen. Zu diesem Zweck stellt Alcatel-Lucent ein Erdungsarmband und eine Erdungsöse an der oberen rechten Seite des Chassis zur Verfügung. Um eine sichere Erdungsfunktion des Erdungsarmbandes sicherzustellen, müssen die Netzteile installiert und mit dem Schutzleiter des Versorgungsstromkreises verbunden sein.

Español: La descarga electrostática (ESD) puede dañar componentes eletrónicos. Usted debe asegurarse que está en contacto con tierra antes de hacer la instalación del equipo. Con este fin, Alcatel-Lucent proporciona una pulsera de muñeca para conectar al chasis en la toma de tierra situada en la parte superior derecha del chasis. Para que la correa de muñeca sea eficaz en la eliminación de ESD, las fuentes de alimentación deben estar instaladas en el chasis y conectadas a enchufes CA con tierra adecuada.

Translated Safety Warnings

Page 80 of the Alcatel-Lucent IP Phone (740) user manual — Appendix B
Page 80 · click to enlarge
Page 80

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

Appendix B

AC Power Specifications

The OA-740 requires AC-input power supply in the range between 100 and 240V. The AC-input power supply uses a power factor correction that complies to EN61000-3-2.

Table 1 lists the AC-input power supply specifications.

Table 1AC Power Supply Specifications

Input voltage 100 to 240 VAC

Input frequency 50 to 60 Hz

Efficiency 65% at minimum measured at nominal AC main voltage and frequency with maximum load on all output

Temperature, operating 0 to 40°C

Temperature, non- operating (storage and shipping)

Humidity 10 - 90% (non-condensing)

PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)
Show 7 more labels / short text on this page
Description Specification · Input · Output · Power output 250W · Environmental Characteristics · -25 to 70°C · Alcatel-Lucent
Page 81 of the Alcatel-Lucent IP Phone (740) user manual — Appendix B Appendix B AC Power Specifications
Page 81 · click to enlarge
Page 81

Agency approvals UL 1950, CSA C22.2 Level 3, TUV EN60950 or VDE EN60950, NEMKO EN60950 (CB Report), CE

Complies with FCC part 15 subpart J Class B and CISPR 22 Class B

AC Power Specifications · Description Specification · Regulatory compliance

Page 82 of the Alcatel-Lucent IP Phone (740) user manual — 4 NC
Page 82 · click to enlarge
Page 82

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

For final production, import color definitions from \\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm. Do not import other template elements such as page layout.

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

To return to the draft version, import color def’ns from draft-colors.fm. To switch to the beta version, import color def’ns from beta-colors.fm

Appendix C

Pin Connector Details for OmniAccess 740

This section describes pin connection details for the OmniAccess 740 (OA-740).

RJ-11 M ODEM C ONNECTOR P IN A SSIGNMENTS

This section details modem connector pin (RJ-11) details for the OA-740.

4 3 2 1

Figure 1RJ-11 Connector
Table 1Pin Connector Details for RJ-11 Connector

RJ-11 Connector Pin Number Signal Name

1 NC

2 Tip or Ring

3 Ring or Tip

4 NC

PaginationNumeric & continuous with preceding section of book
Optional footerManual title (to set, redefine ManualTitle variable)

Alcatel-Lucent

Page 83 of the Alcatel-Lucent IP Phone (740) user manual — RJ-45 C ONSOLE C ONNECTOR P IN A SSIGNMENTS
Page 83 · click to enlarge
Page 83

Pin Connector Details for OmniAccess 740

RJ-45 C ONSOLE C ONNECTOR P IN A SSIGNMENTS

This section details the console connector pin (RJ-45) details for the OA-740.

Alcatel-Lucent IP Phone (740) — RJ-45 C ONSOLE C ONNECTOR P IN A SSIGNMENTS diagram (page 83)
Fig. 12
Figure 2RJ-45 Connector
Table 2Pin Connector Details for RJ-45 Connector

RJ-45 Connector Pin # Signal Name

1 Connected to pin 8

2 Connected to pin 7

7 Connected to pin 2

8 Connected to pin 1

Show 4 more labels / short text on this page
3 Transmit · 4 Signal ground · 5 Signal ground · 6 Receive
Page 84 of the Alcatel-Lucent IP Phone (740) user manual — 6 NC
Page 84 · click to enlarge
Page 84

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Pin Connector Details for OmniAccess 740

T1E1 C ONNECTOR P IN A SSIGNMENTS

The following table details the T1E1 connector pin details for the OA-740:

Table 3T1E1 Card Port Connector Pin Assignment

Pin # Signal Name

3 NC (No Connection)

6 NC

7 NC

8 NC

Show 4 more labels / short text on this page
1 Receive Ring · 2 Receive Tip · 4 Transmit Ring · 5 Transmit Tip
Page 85 of the Alcatel-Lucent IP Phone (740) user manual — 5 NC TD2 -
Page 85 · click to enlarge
Page 85

Pin Connector Details for OmniAccess 740

SE/L2GE C ONNECTOR P IN A SSIGNMENTS

The following table details the SE/L2GE connector pin details for OA-740 system.

Table 410/100/1000 Mbps Port Connector Pin Assignment on SE/L2GE Card

Pin # In 10 Base-T and 100 Base-Tx

In 1000 Base-Tx Mode

1 TX + TD0 +

2 TX - TD0 -

3 RX + TD1 +

4 NC (No Connection) TD2 +

5 NC TD2 -

6 RX - TD1 -

7 NC TD3 +

8 NC TD3 -

Mode

Page 86 of the Alcatel-Lucent IP Phone (740) user manual — S ERIAL C ARD (V.35/X.21) C ONNECTOR P IN A SSIGNMENTS
Page 86 · click to enlarge
Page 86

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Pin Connector Details for OmniAccess 740

S ERIAL C ARD (V.35/X.21) C ONNECTOR P IN A SSIGNMENTS

This section details the Serial Card connector pin (V.35/X.21) details for OA-740 system.

Alcatel-Lucent IP Phone (740) — S ERIAL C ARD (V.35/X.21) C ONNECTOR P IN A SSIGNMENTS diagram (page 86)
Fig. 13
Figure 3Serial Card (V.35/X.21) Connector
Table 5Pin Connector Details for Serial Line Card
Alcatel-Lucent IP Phone (740) — S ERIAL C ARD (V.35/X.21) C ONNECTOR P IN A SSIGNMENTS diagram (page 86)
Fig. 14
Page 87 of the Alcatel-Lucent IP Phone (740) user manual — B10 P2P3_CMODE0 B44 P2P3_CMODE1
Page 87 · click to enlarge
Page 87

Pin Connector Details for OmniAccess 740

Pin# Signal Name Pin# Signal Name

A16 Signal Ground A50 Signal Ground

A17 PORT1_TXC_B A51 PORT1_TXC_A

A18 CHASSIS_GND A52 Signal Ground

A19 PORT0_RTS_B A53 PORT0_RTS_A

A20 PORT0_CTS_B A54 PORT0_CTS_A

A21 PORT0_DSR_B A55 PORT0_DSR_A

A22 PORT0_DCD_B A56 PORT0_DCD_A

A23 PORT0_DTR_B A57 PORT0_DTR_A

A24 PORT0_RI A58 PORT0_RL

A25 PORT0_TM A59 PORT0_LL

A26 PORT0_RxD_B A60 PORT0_RxD_A

A27 P0P1_CMODE0 A61 P0P1_CMODE1

A28 PORT0_TxD_B A62 PORT0_TxD_A

A29 P0P1_CMODE2 A63 P0P1_CMODE3

A30 PORT0_RxTiming_B A64 PORT0_RxTiming_A

A31 P0P1_CMODE4 A65 Signal Ground

A32 PORT0_TxTiming_B A66 PORT0_TxTiming_A

A33 Signal Ground A67 Signal Ground

A34 PORT0_TXC_B A68 PORT0_TXC_A

B1 CHASSIS_GND B35 Signal Ground

B2 PORT2_RTS_B B36 PORT2_RTS_A

B3 PORT2_CTS_B B37 PORT2_CTS_A

B4 PORT2_DSR_B B38 PORT2_DSR_A

B5 PORT2_DCD_B B39 PORT2_DCD_A

B6 PORT2_DTR_B B40 PORT2_DTR_A

B7 PORT2_RI B41 PORT2_RL

B8 PORT2_TM B42 PORT2_LL

B9 PORT2_RxD_B B43 PORT2_RxD_A

B10 P2P3_CMODE0 B44 P2P3_CMODE1

Page 88 of the Alcatel-Lucent IP Phone (740) user manual — B34 PORT3_TXC_B B68 PORT3_TXC_A
Page 88 · click to enlarge
Page 88

Except on the first page, right running head: Heading1 or Heading1NewPage text (automatic)

Pin Connector Details for OmniAccess 740

Pin# Signal Name Pin# Signal Name

B11 PORT2_TxD_B B45 PORT2_TxD_A

B12 P2P3_CMODE2 B46 P2P3_CMODE3

B13 PORT2_RxTiming_B B47 PORT2_RxTiming_A

B14 P2P3_CMODE4 B48 Signal Ground

B15 PORT2_TxTiming_B B49 PORT2_TxTiming_A

B16 Signal Ground B50 Signal Ground

B17 PORT2_TXC_B B51 PORT2_TXC_A

B18 CHASSIS_GND B52 Signal Ground

B19 PORT3_RTS_B B53 PORT3_RTS_A

B20 PORT3_CTS_B B54 PORT3_CTS_A

B21 PORT3_DSR_B B55 PORT3_DSR_A

B22 PORT3_DCD_B B56 PORT3_DCD_A

B23 PORT3_DTR_B B57 PORT3_DTR_A

B24 PORT3_RI B58 PORT3_RL

B25 PORT3_TM B59 PORT3_LL

B26 PORT3_RxD_B B60 PORT3_RxD_A

B27 No Connect B61 No Connect

B28 PORT3_TxD_B B62 PORT3_TxD_A

B29 No Connect B63 No Connect

B30 PORT3_RxTiming_B B64 PORT3_RxTiming_A

B31 No Connect B65 Signal Ground

B32 PORT3_TxTiming_B B66 PORT3_TxTiming_A

B33 Signal Ground B67 Signal Ground

B34 PORT3_TXC_B B68 PORT3_TXC_A

Page 89 of the Alcatel-Lucent IP Phone (740) user manual — CTS V.28 106 D DCE -> DTE
Page 89 · click to enlarge
Page 89

Pin Connector Details for OmniAccess 740

SERIAL CARD V.35 DTE CABLE PIN-OUT DETAILS

The following table lists the V.35 DTE cable pin out at the M-34 Winchester connector:

Table 6Serial Card V.35 DTE Cable Pin-out

V.35 Circuit Number

TxD(A) V.35 103 P DTE -> DCE

TxD(B) V.35 103 S DTE -> DCE

TT(A) (DTE supplied timing)

V.35 113 U DTE -> DCE

TT(B) (DTE supplied timing)

V.35 113 W DTE -> DCE

RTS V.28 105 C DTE -> DCE

DTR V.28 108 H DTE -> DCE

RL V.28 140 N DTE -> DCE

LL V.28 141 L DTE -> DCE

RxD(A) V.35 104 R DCE -> DTE

RxD(B) V.35 104 T DCE -> DTE

RxC(A) V.35 115 V DCE -> DTE

RxC(B) V.35 115 X DCE -> DTE

TxC(A) V.35 114 Y DCE -> DTE

TxC(B) V.35 114 AA DCE -> DTE

CTS V.28 106 D DCE -> DTE

DSR V.28 107 E DCE -> DTE

DCD V.28 109 F DCE -> DTE

RI V.28 125 J DCE -> DTE

TM V.28 142 NN DCE -> DTE

Signal Ground - - B -

Show 6 more labels / short text on this page
M-34 Winchester · Signal Name Signal · Male connector · Direction · Type · Pin #

Ask about the Alcatel-Lucent IP Phone (740)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Alcatel-Lucent IP Phone (740)

Be the first to ask — other owners or our team will answer.

Original document

Alcatel-Lucent IP Phone (740) manual PDF

92 pages·1.4 MB·IP Phone·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…