Instruction/ maintenance manual of the product PM1850SBH Electrolux
Go to page of 76
Manuel d’instructions Merci de lire trés attentivement le manuel d'instructions. Assurez-vous d'avoir tout compris avant d'utiliser ce tracteur. Manual de las instrucciones Por favor lea cuidadosamente y comprenda estas intrucciones antes de usar esta maquina.
2 We reserve the right to make changes without prior notice. Ånderungen ohne vorherige Mitteilung sind vorbehalten. Nous nous réservons le droit d'apporter des modifications sans avis préalable. Nos reservamos el derecho a introducir modificaciones sin previo aviso.
3 1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I .
4 • Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
5 1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN.
6 • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absenken. - In Leerlauf schalten und die Feststellbremse einlegen. - Den Motor abstellen und den Zündschlüssel abziehen. • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw.
7 1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tondeuses autoportées ATTENTION : CETTE TONDEUSE EST CAPABLE D’AMPUTER LES MAINS, LES PIEDS ET DE PROJETER DES OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ SUIVANTES PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES ET ÉVENTUELLEMENT MORTELLES.
8 • Débrayez les lames, arrêtez le moteur, et débranchez le (s) fil (s) de la bougie d'allumage ou enlevez la clef de contact: - avant de retirer l'insert broyeur ou avant de retirer la goulotte d'éjection pour la nettoyer.
9 1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
10 • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
11 1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE : QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA.
12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e .
13 1. V eiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN.
14 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
15 BATTERY BATTERIE BATTERIE ACCU BATERÍA BATTERIA CAUTION VORSICHT DANGER OPGELET PRECAUCIÓN ATTENZIONE BEWARE OF THROWN OBJECTS VORSICHT, HOCHGESCHLEUDERT GEGENSTÄNDE ATTENTION AUX PROJECTILES LE.
16 NO OPERATION ON SLOPES MORE THAN 10 NICHT AUF ABHÄNGEN MIT MEHR ALS 10 STEIGUNG BETREIBEN N'UTILISEZ JAMAIS SUR DES PENTES DE PLUS DE 10 NIET OP HELLINGEN VAN MEER DAN 10 GEBRUIKEN NO OPERE S.
17 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSAC-HEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CEGUE-DAD O LESIONES.
18 Eng F Esp NL Before the tractor can be used certain parts must be as- sembled, which for transportation reasons are enclosed in the packing. The picture shows which parts must be as- sembled. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpack-ung lose beigefügt sind.
19 VOLANTE DE DIRECCIÓN • Introduzca el eje de extensión (1). Apriete en forma segura. • Montar la cubierta del eje del volant. Assegurarse de que las espigas de guía de la cubierta encajan en los orificios respectivos. • Remueva el adaptador del volante y deslice el adaptador sobre la extensión del eje de dirección.
20 1 Seat Remove the hardware securing seat to the cardboard pack- ing and set the hardware aside for assembly of seat to tractor. Pivot seat upward and remove from cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
21 3 Eng Esp NOTE! Check that the flex is correctly connected to the safety switch (3) on the seat holder. HINWEIS! Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist. REMARQUE! Vérifier que le cordon est correctement branché à l’interrupteur de sécurité (3) sur le support du siège.
22 2 NOTE: If battery is put into service after month and year indicated on label, charge battery for minimum of one hour at 6-10 amps. WARNING: Before installing battery remove metal brace- lets, wrist watch bands, rings, etc. from your person. Touch- ing these items to battery could result in burns.
23 2 ASSEMBLE GAUGE WHEELS The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower performance. • Slide adjusting bar down into bracket channel, Be sure that adjusting bar aligning holes are on top.
24 1. Rueda limitadora 2. Barra de ajuste 3. Bulón de perno 4 . Arandela 5. Contratuerca 6. Pasador roscado 7. Muelle de retención MONTAGGIO DELLE RUOTE LIMITATRICI DELLA PROFONDITA’ DI ARATURA Le.
25 2 A B Eng INSTALL MOWER AND DRIVE BELT Be sure tractor is on level surface and mower suspension arms (3) are raised with attachment lift control. Engage parking brake. • Cut and remove ties securing anti-sway bar (1) and belts. Swing anti-sway bar to left side of mower deck.
26 2 A B 1 2 3 4 5 6 7 8 9 INSTALLATION VON MÄHER UND FÖRDERBAND Versichern Sie sich, dass sich der Traktor auf einer ebenen Oberfläche befindet und dass sich die Aufhängungsarme des Mähers (3) mit Zusatzgerät Hubsteuerung oben befinden. Feststellbremse einrasten lassen.
27 2 A B 1 2 3 4 5 6 7 8 9 MONTAGE DE LA TONDEUSE ET DE LA COURROIE D’ENTRAÎNEMENT Assurez-vous que le tracteur soit bien à plat et que les bras de suspension (3) soient soulevés et assurés. Tirez le frein à main. • Coupez et enlevez les liens et les courroies qui fixent la barre anti-dévers (1).
28 2 A B 1 2 3 4 5 6 7 8 9 Esp INSTALAR EL CORTACÉSPED Y LA CORREA DE TRANSMISIÓN Asegurarse de que el tractor esté en una superficie plana y los brazos de suspensión del cortacésped (3) estén levantados con el mando de levantamiento. Poner el freno de mano.
29 2 A B 1 2 3 4 5 6 7 8 9 COME INSTALLARE LA TOSAERBA E LA CINGHIA DI TRASMISSIONE Verificare che il trattore si trovi su una superficie piana e che i bracci di sospensione della tosaerba (3) siano sollevati attraverso il comando di sollevamento previsto.
30 2 NL A B 1 2 3 4 5 6 7 8 9 INSTALLEER MAAIER EN AANDRIJVER Verzeker u dat de traktor waterpas staat en dat de armophanging (3) van de maaier omhoog staat met behulp van het lifthulpstuk. Zet de parkeerrem erop. • Maak de verpakking om de antislingerstaaf (1) en riemen los en gooi deze weg.
31 Eng TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
32 3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 1 6 3 7 8 2 9 5 10 Positioning of controls 1. Light Switch Position. 2. Throttle control.
33 Emplacement des commandes 1. Interrupteur des phares. 2. Commande de gaz. 3. Pédale de frein. 4. Embrayage et débrayage de la boîte de vitesses. 5. Embrayage et débrayage de l’unite de coupe. 6. Abaissement et relevage du plate au de coupe. 7.
34 1. Light switch position 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting Eng Esp 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades.
35 3. Brake Pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Bremspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst.
36 4. Motion control lever There are four different positions for this lever: N = Neutral (no drive) S = Slow F = Fast R = Reverse The lever can be moved steplessly between S and F to ensure the required speed.
37 6. Quick lifting/lowering of the cutting unit Pull the lever backwards to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During transporta- tion the cutting unit shall be in the highest position. Pull the lever back until it locks.
38 OFF ON START 7. Ignition Lock There are three different positions for the ignition key: O F F All electric current broken. ON Electric current connected. START Start mot or connected. WARNING! Never leave the key in the ignition lock when leaving the machine on its own.
39 8. Parking brake Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3. Release the brake pedal. To release the parking brake all that is necessary is to push down the brake pedal.
40 10. Free-wheel Control Lever To tow or move the tractor without the aid of the engine, the free-wheel control knob must be pulled out and locked in position. 10. Ein-und Ausschalten des Freilaufes Um den Traktor ohne Motorkraft abzuschleppen oder anzuschieben, muß der Freilauf-Steuerungsknopf herausgezogen.
41 11. Cutting height setting The required cutting height is set with the aid of the wheel. The cutting height is increased when it is turned clockwise. The wheel is easier to turn if the lever for lifting/lowering of the cutting unit is pulled backwards at the same time.
42 4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarr er . 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole.
43 ADD FULL CAUTION - DO Eng The oil level should lie between the two markings on the oil stick. If more oil is needed add SAE 30 oil to the “FULL” marking. SAE 5W-30 oil should be used during the winter (below freezing point). Der Ölstand soll zwischen den beiden Marken auf dem Meßstab liegen.
44 Tire air pressure Check the tire pressure regularly. The pressure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
45 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Eng Esp Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Tirer le starter (si le moteur est froid). Extraer el estrangulador (únicamente si el motor está frío).
46 Turn the ignition key to “START position”. NOTE! Do not run the start motor more than 5 seconds at once. If the engine will not start, wait about 10 seconds before the next try. Zündschlüssel auf “START” drehen. HINWEIS! Den Anlasser nicht jeweils länger als ca.
47 IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BELOW 40°F[4°C]) - AF- TER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEUTRAL (N) POSITION AND RELEASING CLUTCH/BRAKE PEDAL.
48 Esp NL • Garez le tracteur avec sûreté sur un terrain plat pour qu’il ne roule pas dans aucune direction. Le frein de stationnement doit être dégagé pour le procédé suivant.
49 NOTA! La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
50 Esp Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other fixed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
51 WARNING! • Do not drive in terrain at an angle of more than max. 10°. The risk for spark-over backwards is large. • In steep terrain the risk for tipping is considerable. • Avoid stopping and starting in sloping terrain. WARNUNG! • Fahren Sie nicht in Gelände mit einer höheren Neigung als höchstens 10°.
52 Use the left side of the machine to cut close to trees, bushes and paths, etc. The blade cuts about 15 mm inside the edge of the cover. Die linke Seite der Maschine benutzen, um in der Nähe von Bäumen, Gebüsch, Gängen usw. zu mähen. Die Mähklinge mäht ca.
53 6. Maintenance, adjustment. 6. W artung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever.
54 6 Esp Esp NL NL Cubierta del motor • Levante la cubierta. • Desenchufe el conector de cables de los faros delanteros. • Colóquese delante del tractor. Mueva la cubierta hacia ambos lados, inclínela hacia delante y extráigala. • Para volver a ponerla, debe introducir los ejes de giro en las ranuras correspondientes del chasis.
55 6 Mantenimiento NOTA : El mantenimiento periódico ha de hacerse con regularidad a fin de mantener el tractor en buen estado. ADVERTENCIA : Antes de efectuar cualquier reparación, inspección o maintenimiento, desconectar el cable de la bujía a fin de evitar accidentes.
56 6 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap.
57 6 Change engine oil ............................................................................ • Lubricate pivot points ........................................................................ • Check brake operation .........................
58 6 COMPE-RENDU D'ENTRETIEN Indiquer les dates après chaque mesure d'entretien Vidange d'huile moteur ..................................................................... • Graissage des articulations ..............................
59 6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore Cambio de ll'olio ............................................................................
60 Blades For best results mower blades must be kept sharp. Replace bent or damaged blades. Sharpening can be carried out with a file or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. BLADE REMOVAL: • Raise mower to highest position to allow access to blades.
61 WARNING! Do not forget to tighten the lock nut after completing adjustment. WARNUNG! Nicht vergessen, die Sicherungsmutter nach durchgeführter Einstellung anzuziehen. ATTENTION! Ne pas oublier de serrer l’écrou de verrouillage après le réglage.
62 1 2 Dismantling of the cutting unit Work from the right side of the machine. 1. Remove the retainer springs (1), (2), (3) and axles. 2. Remove the two rear retainer springs (4) and knock off the axle taps with a hammer. 3. Take off the belt from the engine pulley (5).
63 B A Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4. Measure the distances A and B.
64 6 1 2 To obtain the best cutting results, the mower blades should be adjusted so the front tip (B) is approximately 1/8” to 1/2” lower than the rear tip (A) when the mower is in itshighest position. 1. Loosen the nut (1) on both the left and right levers.
65 6 “A” 2 REGLAGE TRANSVERSAL • Relever le carter de coupe dans sa position la plus haute. • Calculer la distance au sol à partir des milieux des bords extérieurs gauche et droite du carter de coupe. • La distance A doit être la mêne des deux côtés à 6 mm près.
66 6 Replacement of drive belt 1. Dismantle the cutting unit as described previously. 2. Pull apart the contact for the cable to the electrical connection (1). 3. Dismantle the motion restrainer for the clutch (2). 4. Engage the parking brake and work off the belt upwards from the pulley (3), the clutch pulley (4).
67 6 TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean.
68 EINSTELLUNG DES STEUERKNÜPPELS DES SCHALTGETRIEBES Der Steuerknüppel wird von der Herstellerfirma im Werk voreingestellt und erfordert daher in der Regel keine weiteren Einstellungen.
69 REGOLAZIONE DELLA LEVA DI COMANDO DEL MOVIMENTO DEL MECCANISMO DEL CAMBIO La leva di comando del movimento del meccanismo del cambio è stata impostata al momento della fabbricazione e non richiede pertanto ulteriori regolazioni.
70 7. T r oubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole.
71 Le moteur ne démarre pas 1. Manque d’essence dans le réservoir. 2. Bougie d’allumage défectueuse. 3. Raccord de bougie défectueux. 4. Impuretés dans le carburateur ou la canalisation de carburant Le démarreur n’entraîne pas le moteur 1.
72 NL 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. Il motorino di avviamento non fa girare il motore 1.
73 The following steps should be taken when mowing sea- so n is over: • Clean the entire machine, especially underneath the cutting unit cover. • Touch up all chipped paint surfaces in order to avoid corrosion. • Change engine oil. • Drain the fuel tank.
74 Aan het einde van elk maaisezoen moeten de volgende maatregelen worden genomen: • Maak de hele machine schoon, in het bijzonder de binnenkant van de kap van de maaikast. • Herstel lakbeschadigingen om roest te voorkomen. • Ververs de olie in de motor.
75.
179903 12.28.01 RH Printed in U.S.A..
An important point after buying a device Electrolux PM1850SBH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux PM1850SBH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux PM1850SBH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux PM1850SBH you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux PM1850SBH will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux PM1850SBH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux PM1850SBH.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux PM1850SBH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux PM1850SBH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
