Instruction/ maintenance manual of the product DFKTWC75GS Electrolux
Go to page of 20
Use & Care Guide Installation Instructions Vent Hood 316495007 - 09/2007.
2.
3 Finding Information Purchase date Electrolux model number Electrolux serial number (see picture for location) Please read and save this guide Thank you for choosing Electrolux , the new premium brand in home appliances.
4 Safety Important Safety Instructions Read all instructions before using this appliance. Save these instructions for future reference. Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type.
5 Safety TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:* 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
6 Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 6 - Mounting Screws (4,8 x 38mm Pan Head) 7 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3.
7 Installation 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible.
8 Installation Wiring GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
9 Installation Install mounting bracket FRAMING BEHIND DRYWALL 37"= bottom of hood 24" above cooktop 43"= bottom of hood 30" above cooktop 37” to 43” above cooktop 1. Construct wood wall framing that is flush with inte- rior surface of wall studs.
10 Installation Prepare the hood NOTE On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. 1. Remove the polystyrene block and the tape (Fig.1).
11 DUCTED CONFIGURATION 1. Install the discharge collar into the duct connector of the range hood. Fig. 6. FIG. 6 DISCHARGE COLLAR DUCT CONNECTOR Non - Ducted Recirculation Kit, Model DFKTWC75GS. 5” diameter duct. 1. Discard discharge collar/damper supplied with the hood.
12 Installation FIG. 9 MOUNTING SCREWS (4.8x38mm) MOUNTING SCREWS (4.8x38mm) RECTANGULAR OPENING WALL MOUNTING BRACKET MOUNTING SCREWS (3.9x9.5mm) FIG.10 PLATE OF THE ELECTRICAL SYSTEM MOUNTING SCREWS (3.9x9.5mm) Install the hood 1. Raise the hood into its mounting position.
13 9. Carefully place the decorative flue on the hood. Fig. 13. - On ducted installation in rooms with 8-foot ceilings , the air vents are concealed. Install the flue with the air vents down. - On non-ducted installations in rooms with 8-foot ceilings , the air vents are exposed.
14 (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filters, pull the metal latch ta b outside and unlock the filter. 2. To install the GREASE filters, align rear filter tabs with slots in the hood. Depress the metal latch tab, push filter into position and release.
15 The grease filters should be cleaned when the filter reset switch will be illuminated. Use a warm detergent solution. Grease filters are dishwasher safe.
16 Operation Controls Dead-front mode IMPORTANT The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. When this occurs, it is impossible to turn the blower OFF with its switch. If you must stop the blower, do it from the integral disconnecting switch located inside the blower housing.
17 Remove the grease filters. Open the fuse box. Replace with the same type of fuse (5x20mm, 4A, 125V). Fuse Key : 5304455332 FUSE BOX This range hood requires two halogen bulbs (max 20W, 12V, Type T3 bulb, G4 Base).
18 Warranty Information In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries, Inc.
19.
04307838/3S.
An important point after buying a device Electrolux DFKTWC75GS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux DFKTWC75GS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux DFKTWC75GS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux DFKTWC75GS you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux DFKTWC75GS will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux DFKTWC75GS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux DFKTWC75GS.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux DFKTWC75GS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux DFKTWC75GS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
