Instruction/ maintenance manual of the product 99852 G Electrolux
Go to page of 24
99852 G Gas Hob Operating Instructions GB PERFECT IN FORM AND FUNCTION.
2 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation z This hob must be installed by qualified personnel, according to the manufacturer ’s instructions and to the relevant British Standards.
3 z Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. z Ensure the control knobs are in the ‘OFF’ position when not in use. z When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.
4 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition.
5 1. Hob T op 2. Semi-rapid Burners 3. Auxiliary Burner 4. Ultra-rapid Burner (triple crown) 5. Control knobs Description of the Hob INSTALLATION Any gas installation must be carried out by a registered CORGI installer , and in accordance with existing rules and regulations.
6 Hob burners T o light a burner: z Push in the relevant control knob and turn it to maximum position. z Upon ignition, keep the knob pushed down about 5 seconds . This will allow the "thermocouple" (fig. 1 - letter C) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.
7 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
8 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre.
9 Service and Spare Parts Customer Care When you contact the Service Centre, they will need the following information: 1 . Y our name, address and post code. 2 . Y our telephone number 3 . Clear and concise details of the fault 4 . The model and the serial number (see rating label on the back of this instruction booklet) 5 .
10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason.
11 Instructions for the Installer Engineers technical data BURNER ULTRA-RAPID SEMI-RAPID AUXILIARY (triple crown) (medium) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMAL POWER (kW) 3 . 8 1.20 1. 9 0.45 1. 0 0.33 NOMINAL FLOW RATE (m 3 /h ) 0.
12 700 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING.
13 Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer . The manufacturer will not accept liability , should the above instructions or any of the other safety instructions incorporated in this book be ignored.
14 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
15 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
16 Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below .
17 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.
19 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check.
20 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . — T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight.
21 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ig.
22 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . 1) T urn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit.
35686-0201 01/04 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www .aeg.hausgeraete.de © Electrolux plc 2003 Grafiche MDM - Forlì From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Electrolux 99852 G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux 99852 G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux 99852 G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux 99852 G you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux 99852 G will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux 99852 G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux 99852 G.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux 99852 G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux 99852 G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
