Instruction/ maintenance manual of the product 137064300A Electrolux
Go to page of 20
137064300 A (080 1) In stallation In struction s Electr olux Front-Load Was her In strucciones de In stalacion Lav adora de car ga frontal Electr olux In struction s d’in stallation Lav euse à char.
2 Finding Information Please r ead and save this guide Thank you for choosing Electrolux , the new pr emium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and pr oduct quality throughout the life of your new appliance.
3 Safety Important Safety Instructions Recognize safety symbols, words and labels Safety items throughout this manual ar e labeled withaWARNINGorCAUTIONbasedontherisk type as described below: T ools and materials needed for installation: WHA T TO DO IF YOU SMELL GAS: Donottrytolightanyappliance.
4 Electrical system r equirements W ater supply requir ements Gr ounding requir ements Drain system r equirements CIRCUIT - Individual, properly polarized and grounded 15 amp.
5 MINIMUMINST ALLA TIONCLEARANCES-Inches(cm) SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Under - Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.54 cm) Installation Requir ements Clearance r equirements 0” (0cm) 0” (0cm) 1” (2.
6 Installation Requir ements 38.00” (96.52cm) 53.00” (134.62cm) 50.6” (128.53cm)* to clear open door 31.50” (80.01cm)* to front of closed door water supply connection on rear of unit ¹ drain hose on rear of unit ² power cord on rear of unit ³ freestand washer on floor floor line floor line washer mounted on optional pedestal 27.
7 Unpacking W asher Removing foam packaging T emporarily remove door tape. 1. Open washer door and remove everything fr om 2. the drum. Close door and reapply door tape. 3. Using a rug, blanket or piece of cardboar d to 4. protect the floor , carefully lay the washer on it’ s back.
8 Unpacking W asher Removing shipping har dware Installing hole plugs NOTE Ru bber ex pans ion mat eri al on spacers may need time to relax befor e they can be easily pulled through shipping hole. IMPOR T ANT Save all shipping bolts and spacers for future use.
9 Installation Instructions raise lower Leveling your washer Excessive noise and vibration can be prevented by properly leveling the washer . For free standing installation and with the 1. washer within 4 feet (1 m) of its final location, place a level on top of the washer .
10 Run some water from the hot and cold faucets 1. to flush the water lines and remove particles tha t mi ght c log the w ater valv e sc ree ns an d to determine which faucet is hot and which is cold supply . Lookintheendofeachwatersupplyinlethose 2.
11 Snap one end of the drain hose hanger 1. (shipped in washer drum) onto the drain hose. Continue wrapping it around the hanger and snap it in place. Place the hook end of the drain hose in the drain 2. opening. Secure the drain hose with the cable tie (provided in the enclosur e package) to the stand - pipe, inlet hose, laundry tub, etc.
12 If your washer has this console: If your washer has this console: Empty washer’ s drum and close door . 1. After you plug in the washer the first time: wake up the washer by pressing any button, r otate cycle 2. knob to hand wash cycle, press the start button and then the cancel button.
13 W ARNING ELECTRICALSHOCKHAZARD Failure to disconnect power sour ce before servicing could result in personal injury or even death. B)RemovingDoorfromHinge 1 Reopen door to 90 degree angle. 2 Remove 4 long, course-thread, counter -sunk hinge screws fr om door .
14 Reversing Door W ARNING ELECTRICALSHOCKHAZARD Failure to disconnect power sour ce before servicing could result in personal injury or even death. C) Removing Hinge from Fr ont Panel 1 With the hinge in open position, remove 2 short, course-thread, panhead scr ews on hinge plate.
15 Reversing Door E)ReattachingDoorLocktoFrontPanel 1 Rotate the door lock and move it to the opposite opening. 2 Connect the harness to the door lock by inserting it in the terminal and firmly pushing it in place. 4 Secure the lock with 2 short, course-thr ead, panhead screws.
16 Reversing Door H)RemovingLatchIndicator 1 Insert flat blade screwdriver into open slot of latch indicator . 2 Gentlypryupwardtor eleasetab. 3 Pull the indicator out and set it aside. 3 Pull the hole plug out and set it aside.
17 insert tab insert tab insert tab insert tab press down and snap press down and snap K)ReattachingStrikerPlate 1 Rotate the striker plate and move it to the opposite side of door above the indicator . 2 Reattach with 2 long, course-thread, counter -sunk screws.
18 M)ReattachingDoorAssembly 1 Open the hinge to a 90 degree angle. 2 Install the door onto the hinge locating pins. N) Reversing T rim Ring 1 T rim ring orientation is marked on the back. 2 Remove the trim ring cover plate. T o remove the cover plate from the right, pivot point is up.
19 If replacements parts ar e needed for your washer , contact the source wher e you purchased your washer ,call1-877-4ELECTROLUX(1-877-435- 3287), or visit our website, www .electroluxappliances.com, for the Electrolux AuthorizedPartsDistributornearestyou.
20 Notes.
An important point after buying a device Electrolux 137064300A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux 137064300A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux 137064300A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux 137064300A you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux 137064300A will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux 137064300A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux 137064300A.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux 137064300A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux 137064300A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
