Instruction/ maintenance manual of the product 115 D Electrolux
Go to page of 17
1 15 D Extractor Hood Installation and Operating Instructions.
2 Introduction 3 Extractor version 3 Recirculating mode 4 Electrical connections 5 Safety warnings for electrician 5 Specifications 8 Installation 9 Safety warnings for kitchen unit installer 9 Wall u.
3 Extractor version The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
4 The air is filtered and recirculated through the front grille. Move the handle F to position F — Fig. 3 . You will need an original AEG KLF60/80 activated carbon filter for the recirculating mode.
5 Electrical connections Please ensure that the voltage and current indicated on the rating plate agree with the voltage of your electricity supply. If your appliance has been equipped with a mains lead with a moulded-on type plug, you must comply with the following regulations: The plug moulded on to the lead incorporates a fuse.
6 Y our appliance must be connected to fix ed wir ing via the use of a doub le pole swiched fused spur outlet with or without pilot lamp . We strongly recommend the appliance is connected b y a quali- fied electrician who is a member of the NICEIC who will comply with the IEE and any local regulations .
7 Y our appliance must be connected to fix ed wir ing via the use of a double pole s wiched fused spur outlet with or without pilot lamp . We strongly recommend the appliance is connected b y a quali- fied electrician who is a member of the NICEIC who will comply with the IEE and any local regulations.
8 Dimensions: Height Width Depth (in mm) 152 599 505 Weight: Net: 8.7 Kg Gross: 9.6 Kg Length of the cable: 140 cm Maximum absorbed power: 230 W Motor absorption: 1 x 150 W Lighting: 2 x 40 W Fan powers (levels), levels in compliance with DIN 44971 Level: Min.
9 Safety warnings for kitchen unit installer Installation When used as an extractor unit, the hood must be fitted with a 100 or 120 mm diameter hose. If the outlet hose is installed in a horizontal position, it must be slanted at an angle of 10° so that the air can flow outside without impediment.
10 Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm 2 , which is to say a larger hole, could reduce the performance of the extractor hood.
11 Wall mounting — Position the template on the wall. — Drill four 8 mm Ø holes in the wall, 2 in points H and 2 in points I . — Fit the four 8 mm screw anchor plugs in the wall. — Screw two 5 x 45 mm screws in points H but do not tighten them fully home.
12 Hood Operation 6 Light switch On/Off The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
13 CLOSED OPEN Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. — Open the latch L and swing the grille downwards. — Fig. 7. — To remove the g rille, pull it forwards from the right and release it.
14 Changing the light bulb Removing the filter — Press the stops N and remove the filter by pulling it down- wards. — Fig. 8 Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit.
15 Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grille. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders.
16 Technical assistance service In case of any enquiries and faults, please call AEG After-Sales Service: When calling please state the following 1. The model number 2. The E-No. 3. The F-No. The manufacturer reserves the right to make alterations in design and colour in the interests of technical development without prior notice.
If your appliance has a fault, please contact our service engineer and state the following numbers: E-Nr. 610 F-Nr. AEG Hausgeräte AG Postfach 1036 D-90327 Nürnberg © Copyright by AEG H 260 287 140 L 489B Ed.
An important point after buying a device Electrolux 115 D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux 115 D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux 115 D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux 115 D you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux 115 D will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux 115 D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux 115 D.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux 115 D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux 115 D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
