Instruction/ maintenance manual of the product EC-FT-420 EC Line
Go to page of 15
EC - FT - 420 BARCODE LABEL PRINTER User’s Manual.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 1 1 General 1.1 Printer Accessories 1.2 General Specifications 1.3 Communicate Interface 1.4 Printer Parts 2 PRINTER INSTA LLATIONS 2.1 Ribbon Installation 2.2 Label Installation 2.3 Label Roll Core 2.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 2 1. General 1.1. Printer Accessories After unpacking, please check the accessories that come with the package and store appropriately.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 3 Image Monochrome PCX,BMP(support after the softw are control: ICO WMF,JPG,EMF Picture, can control the picture amplification, reduced, .
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 4 1.3. Communication Interface Parallel Interf ace Interface cab le : Parallel ca ble compatib le to IBM PC Pin out : See below PIN NO.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 5 1 Upper cover opens a button 11 LED Light(Ready) 2 Top Cover 12 LED Light (Status) 3 Ribbon Rewind W heel 13 Ribbon Supply Shaft 4 Lock.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 6 2. Pri nter Installation This printer model has the following print mo des ： Thermal Transfer (TT) ： W hen printing, ribbon m ust be installed to tra nsfer the print contents onto the media.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 7 4. Feed the ribbon from the Ribbon Supply Shaft under the Print Head. 5. Warp the ribbo n around the Ribbon Shaft and stick th e ribbon o nto the Empty Ribbon Roll Core 。 6. Firmly close the upper print mechanisms.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 8 2. Place the label roll onto the Label Roll Core. 3. Loosen and lift the upper print mechanism by pressing the locking buttons. 4. Feed the label through the two Label Guides to the Tear-off Bar.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 9 2.3. Label Roll Core Installation Instruction (A) 1” roll core installation (B) 1.5” roll core installation (C) 3” roll core installation 2.4. PC Connection 1. Please make sure the printer is powered off.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 10 3. Control Panel 3.1. FEED Key After pressing the FEED key, printer will send the media (according to media type) to the specified stop position. W hen printing with continuous med ia, pressing the FEED key will feed med ia out to a certain length.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 11 Ready Indicator Show the printer status Green: printer is ready to operate Blinking: printer is paused Power indicator Shows the power and error status Off -printer power off Green ： printer power off Blinking ： error occurs Performing Calibration 1.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 12 NOTE: All se ttings are stored in non -volatile E2PROM and ca nnot be de stroyed even turn off the printer . Notes ： If you are just updating your driv er,make sure to delete the previous v ersion f irst .
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 13 4. Maintenance and A djustment 4-1. Maintenance and Ad justment Thermal Pr int Head Clean ing Unclear print outs may be caused by dusty print head, ribbon stain or label liner glue. There fore when printing, it’s n ecessary to keep the top c over close d.
EC FT - 420 Barcode Printer User Manual ® Copy right 2010 P . 14 4-2. Troublesho oting Problem Recomme nded Solution Power on the printer, but the LED does not light up Check the pow er connect or LE.
An important point after buying a device EC Line EC-FT-420 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought EC Line EC-FT-420 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data EC Line EC-FT-420 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, EC Line EC-FT-420 you will learn all the available features of the product, as well as information on its operation. The information that you get EC Line EC-FT-420 will certainly help you make a decision on the purchase.
If you already are a holder of EC Line EC-FT-420, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime EC Line EC-FT-420.
However, one of the most important roles played by the user manual is to help in solving problems with EC Line EC-FT-420. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device EC Line EC-FT-420 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
