Instruction/ maintenance manual of the product ID 128 Eagle
Go to page of 32
1 ® Fish ID 128 Fish ID 128 Fish ID 128 Fish ID 128 Fish ID 128 INST INST INST INST INST ALLA ALLA ALLA ALLA ALLA TION AND OPERA TION AND OPERA TION AND OPERA TION AND OPERA TION AND OPERA TION TION .
2 Eagle Electronics PO Box 669 Catoosa, OK 74015 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION .............................................................................................. 3 SPECIFICATIONS .
3 SPECIFICATIONS Dimensions ...................... 5.9" W x 5.35" H x 3.4" D Input Voltage .................... 10 - 15 vDC Current Drain ................... 150 ma (lights off) ........................... 250 ma (lights on) Transmitter Frequency .
4 INSTALLATION - Bracket You can install the unit on the top of a dash or from an overhead with the supplied bracket. It can also be installed in the dash with an optional IDA- 3 or IDA-4 mounting kit. If you use the supplied bracket, you may be interested in the optional GBSA-1 swivel bracket kit.
5 PERMANENT MOUNT TRANSDUCER INSTALLATION The HS-WSPC supplied with your sonar is a transom mount transducer. It can be installed on any outboard or stern-drive (inboardoutboard) powered boat. The “kick-up” mounting bracket helps prevent damage if the transducer strikes an object while the boat is moving.
6 4. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps, and areators can be displayed on the sonar’s screen. Use caution when routing the trans- ducer cable around these wires.
7 RATCHETS NUT MET AL W ASHER R UBBER W ASHERS MET AL W ASHER BOL T remov e the transducer and r atchets from the brac k et. Place the ratch- ets into the holes in the brac ket with the letter “B” aligned with the dot stamped in the brac k et. Reassemble the transducer and br ac k et and place them against the transom.
8 4. Hold the transducer and brac k et assemb ly against the transom. The transducer should be roughly parallel to the g round. The bottom of the transducer brac k et should be in line with the bottom of the hull. Don't let the brac k et e xtend belo w the hull! Mark the center of the slots f or the mounting holes.
9 6. Route the transducer cab le to the sonar unit. Make cer tain to leav e some slack in the cab le at the tr ansducer as shown at the bottom of the pre vious page .
10 POWER CONNECTIONS -PERMANENT MOUNT UNITS ONLY IMPORTANT! INSTALL THE TRANSDUCER BEFORE WIRING THE POWER CABLE! The Fish ID 128 works from a 12 volt DC system only. For the best results, run the power cable directly to the boat’s battery. Keep the power cable away from other boat wiring, especially the engine’s wires.
11 FISH ID 128 PORTABLE ASSEMBLY INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES Release the latch on the front of the battery case. Open the compartment and install eight "D" cell batteries into the adapter.
12 WASHER WASHER NUT BOLT TIE NYLON CORD HERE SCREW PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY Assemble the transducer and bracket as shown below. Attach the transducer to the bracket with the supplied hardware.
13 Clean the chosen area of the hull before attaching the suction cup. Locate the transducer on the hull as shown below. Don't allow the bracket to go below the hull, as water pressure against it can cause the suction cup to come off at speed. Moisten the cup, then press it onto the hull as firmly as possible.
14 KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unit has accepted a command. PWR/CLEAR Use this key to turn the unit on and off. It also clears menu selections and the menus from the screen. Note! To turn the unit off, press and HOLD the PWR/CLEAR down.
15 NOTE: Turning the unit off erases all user settings and it returns to the system defaults. For example, if you turn the lights on, then turn the unit off, the next time you turn the unit on, the lights will be off, since the default setting for the lights is off.
16 RANGE You can’t adjust the range when the auto- matic mode is on. It is adjustable when the unit is in the manual mode, however. To do so, first put the unit in the manual mode. Now press a menu key until the “RANGE SEL” menu appears as shown at right.
17 SENSITIVITY The sensitivity menu lets you control the unit’s ability to pick up echoes. A low sensitivity level excludes much of the bottom information, fish signals, and other detail. High sensitivity settings lets you see features, but it can also clutter the screen with noise and other unwanted signals.
18 floats, air bubbles, etc. Individual tree limbs extending outwards from a group of limbs are the hardest objects for the Fish ID feature to distinguish from fish. You may see Fish ID symbols on the screen when, in fact, there are no fish. Practice with the unit when the Fish ID feature is on and off to become more familiar with Fish ID.
19 CHART SPEED The rate echoes scroll across the screen is called the chart speed. It’s adjustable by pressing a menu key until the chart speed menu appears. Chart speed is set to maxi- mum when the unit is first turned on. To decrease it, press the down arrow key.
20 ALARMS FISH ALARM The Fish Alarm sounds a tone when a fish symbol appears on the screen. To use the fish alarm, press a menu key until the “FISH ALARM” menu appears on the screen. Now press the up arrow key to turn the alarm on. Repeat the above steps to turn the alarm off.
21 LIGHTS The display is backlighted for night use. To turn the backlights on or off, press a menu key repeatedly until the back light menu appears. Now press the up arrow to turn the lights on or the down arrow to turn them off. The menu will clear automatically after a few seconds.
22 automatically after a few seconds or press the PWR/CLEAR key to clear the screen. ASP (Advanced Signal Processing) ASP is a program embedded in the computer that is specifically designed to eliminate noise. It continually monitors the signals from the receiver, determines which echoes are noise and rejects them.
23 A A A A A BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL A A A A A C C C C C B B B B B B B B B B C C C C C FISH ARCHES FISH ARCHES FISH ARCHES FISH ARCHES FISH ARCHES Fish arches are created when the cone of sound passes over a fish.
24 One of the best ways to get fish arches is to expand or “zoom” a segment of the water. For example, from 45 to 60 feet. The smaller the segment, the better the screen resolution will be. The easiest way to do this is with the Zoom feature. This feature expands the echoes, making it easier to see detail.
25 SURFACE LAYER ABSORBS HEAT FROM THE SUN EPILIMNION THERMOCLINE MOST PRODUCTIVE ZONE FOR FISHING HYPOLIMNION Unit won’t turn on: 1. Check the power cable’s connection at the unit. Also check the wiring. 2. Make certain the power cable is wired properly.
26 Unit freezes, locks up, or operates erratically: 1. Electrical noise from the boat’s motor, trolling motor, or an accessory may be interfering with the sonar unit. Rerouting the power and transducer cables away from other electrical wiring on the boat may help.
27 rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. Try using resistor spark plugs or routing the sonar unit’s power and transducer cables away from other electrical wiring on the boat.
28 unit’s power cable and transducer cable away from the wiring that is causing the interference. VHF radio antenna cables radiate noise when transmitting, so be certain to keep the sonar’s wires away from it. You may need to route the sonar unit’s power cable directly to the battery to isolate it from other wiring on the boat.
29 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY “We", “our”, or “us” refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. “You” or “your” refers to the first person who purchases this product as a consumer item for personal, family, or household use.
30.
31 Ho w to Obtain Ser vice (Canadian Customers Only) We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you need service or repairs, contact the Eagle Factory Customer Service Department at the toll-free number listed below.
32 Eagle Electronics may find it necessary to change or end our shipping policies, regulations, and special offers at any time. We reserve the right to do so without notice. Accessory Ordering Information To order accessories such as power cables or transducers, please contact: 1) Your local marine dealer.
An important point after buying a device Eagle ID 128 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Eagle ID 128 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Eagle ID 128 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Eagle ID 128 you will learn all the available features of the product, as well as information on its operation. The information that you get Eagle ID 128 will certainly help you make a decision on the purchase.
If you already are a holder of Eagle ID 128, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Eagle ID 128.
However, one of the most important roles played by the user manual is to help in solving problems with Eagle ID 128. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Eagle ID 128 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
