Instruction/ maintenance manual of the product 5232IM Dynex
Go to page of 19
CD-WRITER 5232IM CD-ReWritable Drive User’s Manual.
DANGER INVISIBLE LASER RADIATION WHEN O PEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATIO N DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYO NS.
FCC Compliance Statement This device complies with Part 15 of the FCC Ru les. Operation is subject to the following two condit ions: 1. this device ma y not cause harmful i nterference, and 2. this device must accept any interferen ce received, including interference that may cause undesired operat ion.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 2 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 Windows Environment 6 S O.
CD-WRITER 5232IM 1 INTRODUCTION CD-WRITER 5232IM is a half-height CD-ReWritable drive of standard IDE interface. It supports maximu m 52X speed writing ability on CD-R discs, 32X speed on CD-RW discs and 52X speed reading performance.
CD-WRITER 5232IM 2 System Requirements For IBM compatible PCs, the system requirements recommended are as follows: ♦ PC sufficient to run Windows 98/ME/2000/XP ♦ Pentium II 350MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
CD-WRITER 5232IM 3 INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four dev ices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive.
CD-WRITER 5232IM 4 You may consider one of the two ways recommended below to connect your drive. ♦ To get the most stable performance for the CD-RW drive to write: Primary IDE Master: Hard Disk Prim.
CD-WRITER 5232IM 5 The red-edge of the IDE Cable must be connected to Pin 1 on the CD- ReWritable drive. 5. If you have a sound card that can be connected to this CD- ReWritable drive, you can connect the drive (as Audio-out) and the sound card (as Audio-in) with a 4- pin audio cable.
CD-WRITER 5232IM 6 Driver Installation Windows Environment CD-WRITER 5232IM is a PnP device, and Windows 98/ME/2000/XP can automatically detect the drive and load the appropriate driver. If Windows cannot detect the driv e, you can operate manually: 1.
CD-WRITER 5232IM 7 CONNECTION & OPERATION Front Panel 12 4 3 1. LED Indicator Flashes “green” while verifying or reading a disc/ writing a CD- R/CD-RW disc. 2. Disc Tray This is the tray for the disc. Pl ace the disc in the tray, then press the Close/Eject button or lightly push the tray to close it.
CD-WRITER 5232IM 8 NOTE: The front panel is subject to change wi thout notice. Rear View 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable.
CD-WRITER 5232IM 9 TECHNICAL DATA Performance Transfer rate Read : CD-ROM/CD-R: 7800kb/s (up to 52X) CD-RW: 6000kb/s (up to 40X) Write: CD-R 7800kb/s (up to 52X) CD-RW 4800kb/s (up to 32X) Access time.
CD-WRITER 5232IM 10 Form factor 5.25" Half Height Disc loading Tray (motorised) Audio output level Line out = 0.6 ± 10%Vrms Headphone out = 0.6± 10%Vrms Power 5 VDC & 12VDC Dimensions Height 41.8 ± 0.2 mm Width 148.6 ± 0.3 mm Depth 177.0 ± 0.
CD-WRITER 5232IM 11 Environment Temperature Operating 5°C to 45°C Non-operating -20°C to 60°C Humidity Operating 8% ~ 80%RH Non-operating 5% ~ 95%RH.
CD-WRITER 5232IM 12 TROUBLESHOOTING To help you get more familiar with CD-WRITER 5232IM, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RM A support from your dealer. Q1. CD-WRITER 5232IM cannot be recognized.
CD-WRITER 5232IM 13 (1) Please check if the audio cable is connected to the audio connector properly. (2) Check both rear side of the CD-RW drive and sound card on M/B (If Audio chipset is on board). If they are well connected, check if the sound card is working.
CD-WRITER 5232IM 14 (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.) (8) Copy data as image file to hard drive to avoid buffer underrun.
3100552360 Version 1.0 March 2004.
An important point after buying a device Dynex 5232IM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dynex 5232IM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dynex 5232IM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dynex 5232IM you will learn all the available features of the product, as well as information on its operation. The information that you get Dynex 5232IM will certainly help you make a decision on the purchase.
If you already are a holder of Dynex 5232IM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dynex 5232IM.
However, one of the most important roles played by the user manual is to help in solving problems with Dynex 5232IM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dynex 5232IM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
