Instruction/ maintenance manual of the product DA304 Dual
Go to page of 16
INSTALLATION / OWNER'S MANUAL Mobile Power Amplifiers PERFORMANCE SERIES DA304 DA602 DA604 DA904 DA4001 DA6001 DA8001.
2 INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your Dual amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnectnegative batteryterminal.
NOTE: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used as a general guideline only. Power Wire (+12V) • Disconnectnegative batteryterminal before proceeding.
DA602 DA304 DA604 DA904 High Level Inputs RCA Line Inputs Pass Through Gain 1 2 3 Hi-Pass Filter Crossover Mode Low-Pass Filter Bass Boost 4 5 6 7 8 INSTALLATION Audio Inputs and Controls 4 8 2 4 1 3 .
DA602 DA304 DA904 DA604 Speaker Connections Fuse(s) +12VDC Battery Connection 1 2 3 Remote Turn On Ground Connection 4 5 INSTALLATION Power and Speaker Connections 5 5 4 1 2 3 5 4 1 2 3 5 4 1 2 3.
DA4001 DA6001 DA8001 RCA Line Inputs Pass Through Gain Phase Control Subsonic Filter 1 2 3 Bass Boost Low Pass Filter Slave/Master Controls Data Link Remote 4 5 6 7 8 9 10 INSTALLATION Audio Inputs an.
DA4001 DA8001 DA6001 Speaker Connections Fuse(s) +12VDC Battery Connection 1 2 3 Remote Turn On Ground Connection 4 5 INSTALLATION Power and Speaker Connections 7 5 4 1 3 2 5 4 1 3 2 5 4 1 3 2.
REM (Remote Turn On) SPEAKERS RCA CABLES GROUND FUSE 12V BATTERY MAXIMUM 12V DC (Power) 2-8 ohms Fuse Rating Whenreplacing fuses,makesure newfuse isthe correcttypeand amperage.Using an incorrect fuse could damage the amplifier.
High-Level Input (speaker cables) Low-Level Input (RCA) Speaker Connections Connect speaker wires observing polarity. The minimum impedance load for the DA304, DA602, DA604 and DA904 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage.
INSTALLATION Master/Slave Mode TheDualmonoampliersfeatureaMaster/Slavemode,wheretwoamplierscanbe connectedtogether.Whentwomonoampliersareconnectedtogether,thepower frombothampliersiscombined.
11 INSTALLATION *MASTER For master amplifier, set the switch to master. This will route the signal through Line-out to the slave amplifier. Set the phase to 0, all adjustments for gain and sound are done on this amplifier. The remote subwoofer control should be connected to master amplifier as well.
The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up.
Problem Cause Action Unit will not turn on (no power LED indicator) +12Vwire notconnected orincorrect voltage.REM wirenot connectedor incorrectvoltage Checkco.
DA602 Power Out put (1 4.4VDC, 20Hz ~ 20kHz): •60 Watts RMS x 2 channels @ 4ohms • 1 00 Watts RMS x 2 channels @ 2ohms • 21 5 Watts RMS x 1 channel @ 4ohms (bridged) Peak Music Power Outpu t: 380 Watts Signal t o noise ratio: 90dB (THD< 0.05% @ 4Ω, 1 4.
INSTALLATION Specifications DA4001 Power Out put (1 4.4VDC, 20Hz ~ 250Hz): •850 Watts RMS x 1 channel @ 2ohms • 1 200 Watts RMS x 1 channel @ 1ohm Peak Music Power Outpu t: 3200 Watts Signal t o noise ratio: > 80dB (THD < 0.5% @ 4Ω, 1 4.4V) Frequency response: 20Hz -1 50Hz (-3dB) Amplifier dimensions: 2” x 9.
DualElectronics Corp. TollFree: 1-866-382-5476 9AM-5PM,EST www.dualav.com ©2014Dual ElectronicsCorp. NSA1113-V01 Thiswarranty givesyou specific legalrights. Youmay alsohave other rightswhich vary from state to state.
An important point after buying a device Dual DA304 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dual DA304 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dual DA304 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dual DA304 you will learn all the available features of the product, as well as information on its operation. The information that you get Dual DA304 will certainly help you make a decision on the purchase.
If you already are a holder of Dual DA304, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dual DA304.
However, one of the most important roles played by the user manual is to help in solving problems with Dual DA304. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dual DA304 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
