Instruction/ maintenance manual of the product 2007 LX Charger Dodge
Go to page of 384
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .................. 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es, which could result in an accident or bodily injury . It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 1 ▫ Ignition Key Removal ................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 2 䡵 Sentry Key ............................ 1 3 ▫ Replacement Keys .
▫ Power Door Locks ..................... 2 4 ▫ Child Protection Door Lock ............... 2 6 䡵 W indows ............................. 2 8 ▫ Power W indows ....................... 2 8 ▫ W ind Buffeting ........................ 3 1 䡵 T runk Lock And Release .
A WORD ABOUT YOUR KEYS Y ou can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer .
• For vehicles equipped with the Electronic V ehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned off. Opening either front door will cancel this featur e.
SENTR Y KEY The Sentry Key Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated.
All of the keys provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only keys that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.
The new Sentry Key is programmed. The Keyless Entry T ransmitter will also be programmed during this pro- cedure. Repeat this procedur e to program up to 8 keys.
system is not arming. Also, if you open a door during the arming period, the system will cancel the arming process. If you wish to rearm the system after closing the door , you must repeat one of the pr eviously described arming sequences.
ILLUMINA TED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position.
T o unlock the doors: Press and r elease the UNLOCK button on the transmitter once to unlock the driver’s door , or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter . This feature can be turned on or of f.
T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the transmitter .
The panic alarm will stay on for 3 minutes unless you turn it off by either pr essing the P ANIC button a second time or drive the vehicle at a speed of 15 mph (24 km/h) or greater . NOTE: • The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the panic alarm is activated.
3. Remove and replace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 4. T o assemble the transmitter case, snap the two halves together .
DOOR LOCKS Manual Door Locks T o lock each door , push the door lock plunger on each door trim panel downward. T o unlock each door , pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door , the door will lock.
Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic V ehicle Information Center (EVIC), refer to “P.
Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors On Exit feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic V ehicle Information Center (.
T o Engage the Child Protection Door Lock 1. Open the rear door . 2. Insert the tip of the vehicle’s ignition key or alike into the child lock control and pull it upwar d.
T o Disengage the Child Protection Door Lock 1. Open the rear door . 2. Insert the tip of the vehicle’s ignition key or alike into the child lock control and pull it downwar d.
W ARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment may result in serious injury or death.
T o close the window part way , lift the window switch to the first detent and release it when you want the window to stop. For vehicles not equipped with the Electronic V ehicle Information Center (EVIC), the power window switches will remain active for 10 minutes after the ignition switch is turned off.
W indow Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the passenger doors. When the switch is pressed, the window contr ols on the passenger doors will not illuminate and the passenger windows will be disabled.
TRUNK LOCK AND RELEASE The trunk lid can be r eleased from inside the vehicle by pressing the T runk Release Button located on the instru- ment panel to the left of the steering wheel. NOTE: The transmission must be in Park before the switch will operate.
T runk Emergency Release The trunk of your vehicle is equipped with an emer gency release handle. It is located on the inside of the tr unk lid, near the latch, and is coated so that it glows in a darkened trunk.
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
BeltAlert Programming The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by performing the following steps: NOTE: DaimlerChrysler does not recommend deacti- vating the Enhanced W arning System (BeltAlert).
distinctive label on the webbing. Children 12 years old and under should be properly r estrained in the rear seat whenever possible. How T o Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted.
Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt r estraint systems. The driver’s airbag is mounted in the center of the steering wheel.
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
2. Infants in rear -facing child restraints should NEVER ride in the front seat of a vehicle with a passenger fr ont airbag. An airbag deployment could cause severe injury or death to infants in that position.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
provide dif ferent rates of airbag inflation from dir ec- tion provided by the ACM. The ACM will not detect roll over . • The ACM also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ST AR T or ON positions.
driver’s front airbag gas is vented thr ough vent holes in the sides of the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way , the airbags do not interfere with your control of the vehicle.
However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately . • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-pr oduct of the process that generates the nontoxic gas used for airbag inflation.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you.
the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and impr ove vehicle performance.
• Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Cruise contr ol status (if applicable) • T raction/stability control status (if applicable) Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
Infants and Child Restraints • Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing: infant carriers and “convertible” child seats.
Children T oo Large For Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat.
Here are some tips on getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it befor e you buy it.
All three r ear-seating positions have lower anchorages that are capable of accommodating LA TCH-compatible child seats. Y ou should NEVER install LA TCH- compatible child seats such that two seats share a com- mon lower anchorage.
Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
T o attach a child restraint tether strap: 1. Rotate the cover over the anchor directly behind the seat where you ar e placing the child restraint. 2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat.
ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not r equired for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Lock Y our V ehicle Always remove the keys fr om the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. T ry to park your vehicle in a well-lit area and never invite theft by leaving articles of value exposed.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be r eplaced after a collision.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 6 6 ▫ Inside Day/Night Mirror ................. 6 6 ▫ Automatic Dimming Inside Mirror — If Equipped .......................... 6 6 ▫ Outside Mirrors .
▫ Folding Rear Seat ...................... 9 3 䡵 T o Open And Close The Hood ............. 9 4 䡵 Lights ............................... 9 5 ▫ Headlight Switch ...................... 9 5 ▫ Automatic Headlights — If Equipped ........ 9 6 ▫ Headlights On W ith W ipers (A vailable W ith Auto Headlights Only) .
䡵 Garage Door Opener (HomeLink 威 )—I f Equipped ............................ 1 0 9 ▫ Programming HomeLink ................ 1 1 0 ▫ Canadian Programming/Gate Pr ogramming . . 1 12 ▫ Using HomeLink ..................... 1 1 3 ▫ Erasing HomeLink Buttons .
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Power Remote-Control Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror , right mirror , or off position. After selecting a mirror , move the knob in the same direction you want the mirr or to move.
HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ).
The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones. If your cellular phone supports a differ ent profile (e.g., Headset Profile), you may not be able to use any UCon- nect™ features.
• For each feature explanation in this section, only the combined form of the voice command is given. Y ou can also break the commands into parts and say each part of the command, when you are asked for it.
NOTE: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing ⬙ and follow the audible prompts.
Call/Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙ 234-567-8901.
• When prompted, enter the number designation (e.g., ⬙ Home, ⬙⬙ W ork, ⬙⬙ Mobile, ⬙ or ⬙ Pager ⬙ ). This will allow you to store multiple numbers for each phonebook entry , if desired. • When prompted, r ecite the phone number for the phonebook entry that you are adding.
• Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Delete. ⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
• The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed thr ough the UConnect™ system if the feature(s) ar e available on your cellular service plan.
Place/Retrieve a Call from Hold T o put a call on hold, press the ⬘ Phone’ button until you hear a single beep. This indicates that the call is on hold. T o bring the call back from hold, pr ess and hold the ⬘ Phone’ button until you hear a single beep.
• After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone.
the paired cellular phone to call the emer gency num- ber . This feature is only supported in the USA. NOTE: The emergency number dialed is based on the Country where the vehicle is pur chased (91 1 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
Y ou can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer service. Some services requir e immediate response selection, in some instances, that may be too quick for use of UConnect™ system.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es).
Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Y our cellular phone can be paired with many dif ferent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time.
Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing.
• UConnect™ phonebook nametag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 85 3.
86 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 87 3.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Power Reclining Seats — If Equipped The recliner contr ol is located on the outboard side of the seat. W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Adjustable restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button, which must be pushed in to lower the head restraint.
settings. Amber LEDs in the top portion of each switch indicate the level of heat in use. T wo LEDs will illuminate for high, one for low , and none for off. Press the switch once to select high-level heating. Pr ess the switch a second time to select low-level heating.
Folding Rear Seat The rear seatbacks can be folded forwar d to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks.
TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel. Next, move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood.
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
Automatic Headlights — If Equipped This system automatically turns the headlights ON or OFF according to ambient light levels. T o turn the system ON, rotate the headlight switch counter -clockwise to the AUTO (A) position. When the system is ON, the Head- light T ime Delay feature is also ON.
T o activate the delay feature, turn of f the ignition switch while the headlights are still on. Then, turn of f the headlights within 45 seconds. The delay interval begins when headlight switch is turned off. If you turn the headlights, park lights, or ignition switch on again, the system will cancel the delay .
Multi-Function Lever The multi-function lever controls the operation of the turn signals, headlight beam selection, and passing lights. The lever is located on the left side of the steering column.
Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pr essing the lens.
Dome Light Position Rotate the dimmer control completely upwar d to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer contr ol is in this position. Interior light Defeat (OFF) Rotate the dimmer control to the extr eme bottom “OFF” position.
CAUTION! T urn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than OFF . Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable.
If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two wipe cycles after releasing the lever and then r esume the intermittent interval previously selected.
The fluid reservoir will hold nearly 1 gallon (4 liters) of washer fluid when the message “Low W asher Fluid” appears in the Electronic V ehicle Information Center (EVIC) — if equipped. W ARNING! Commercially available windshield washer solvents are flammable.
W ARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle.
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
T o Activate: Push the speed control lever inwar d (toward the steering column) and release (“ON/OFF”). The indicator light in the lever (and in the instrument cluster on some models) will illu- minate to show that the speed control system is ON. T o turn the system OFF , push the lever inward (towar d the steering column) again and release.
T o Resume Speed: If you deactivated the speed control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the pr evious set speed. T o do so, push the lever up and release (RES/ ACCEL), and then remove your foot fr om the accelerator pedal.
W ARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Y our vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery .
Sunglasses Storage At the rear of the console, a compartment is pr ovided for the storage of a pair of sunglasses. The storage compartment access is a ⬙ push/push ⬙ design. Push the finger depression on the over head console to open. Push the finger depression to close.
Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that you install a new battery in the hand-held transmitter of the device being programmed. This will allow for quicker training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outer HomeLink buttons. Release the buttons only when the EVIC displays “Chan- nels Cleared” (after 20 seconds); however , do not hold the buttons for longer than 30 seconds. Do not repeat this step if programming a second or thir d hand-held trans- mitter to the remaining HomeLink buttons.
NOTE: If your garage door opener fails to respond to the programmed HomeLink 威 Universal T ransceiver , and your garage door opener is manufactured after 1995, it may have a multiple security code system (rolling code system).
NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the ⬙ cycling ⬙ process to pr event possible overheating.
For questions or comments, contact HomeLink at: www .homelink.com or 1-800-355-3515 . Security If you sell your vehicle, be sure to erase the fr equencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada.
W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Pinch Protect Override If a known obstruction (ice, debris, etc.) pr events closing, press the switch forwar d and hold for two seconds after the reversal occurs. This allows the sunr oof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed.
For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to 60 minutes after the ignition switch is turned off. Opening either fr ont door will cancel this feature.
The center console outlet is powered dir ectly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or pr event engine starting. Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
CUP HOLDERS Front Seat Cup Holders — Standard The cup holders are located in the forwar d edge of the center console. Front Seat Cup Holders — Premium The cup holders are located in the forwar d edge of the center console. Push down on the cover as shown to expose the cup holders.
Rear Seat Cup Holders The rear seat cup holders ar e located in the center armrest between the rear seats. The cup holders ar e positioned forward in the armr est and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the r ear occupants’ el- bows.
Cargo Area The 60/40 split-folding rear seat pr ovides cargo-carrying versatility . The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they pr ovide a continuous, nearly flat extension of the load floor .
W ARNING! • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. T o avoid loss of control result- ing in personal injury , follow these guidelines for loading your vehicle: • Always place cargo evenly on the car go floor .
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel And Controls ............ 1 2 6 䡵 Base Instrument Cluster ................. 1 2 7 䡵 Premium Instr ument Cluster — If Equipped . . . 128 䡵 Instrument Cluster Descriptions .....
▫ Operation Instructions - CD Mode ......... 1 5 4 ▫ Operation Instructions - Auxiliary Mode ..... 1 5 5 ▫ Operating Instructions - Hands Fr ee Phone — If Equipped ......................... 1 5 6 ▫ Operating Instructions - Satellite Radio — If Equipped .
䡵 V ideo Entertainment System (Sales Code XR V) — If Equipped .......................... 1 7 2 䡵 Satellite Radio — If Equipped ............. 1 7 3 ▫ System Activation ..................... 1 7 3 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) .
INSTRUMENT P ANEL AND CONTROLS 1 — Air Outlet 6 — Radio 1 1 — Ignition Switch 2 — Instrument Cluster 7 — Climate Control 12 — Hood Release 3 — Hazard Switch 8 — Heated Seat Switch* 13 .
BASE INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 127 4.
PREMIUM INSTRUMENT CLUSTER — IF EQUIPPED 128 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Base Cluster The word ⬙ TRIP ⬙ will appear when this button is pr essed.
7. Electronic Thr ottle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if ther e is a problem with the Elec- tronic Thr ottle Control system.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
12. Electronic Stability Pr ogram (ESP)/T raction Control System (TCS) Indicator Light — If Equipped If this indicator light flashes during accelera- tion, ease up on the accelerator and apply as little throttle as possible. Adapt your speed and driving to the prevailing r oad condi- tions, and do not switch off the ESP or TCS — if equipped.
16. Seat Belt Reminder Light This light will turn on for 5 to 8 seconds as a bulb check when the ignition switch is first turned ON. A chime will sound if the driver’s seat belt is unbuckled during the bulb check.
The dual brake system provides a r eserve braking capac- ity to a portion of the hydraulic system in the event of a failure. Failur e of either half of the dual brake system is indicated by the Brake W arning Light, which will turn on when the brake fluid level in the master cylinder drops below a specified level.
21. V ehicle Security Alarm (VSA) Indicator Light — If Equipped The VSA indicator Light flashes rapidly when the VSA is arming, and slowly when the VSA is armed.
CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Certain conditions such as a loose or missing gas cap, poor fuel quality , etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not requir e towing.
• System Status • V ehicle information warning message displays • Personal Settings (customer programmable featur es) • Compass display • Outside temperature display • T rip computer funct.
If Compass/T emp/Audio is already displayed when the AUDIO MODE button is pressed, then the radio mode will change from AM to FM, to T ape, to CD, or to Satellite (SA T) accordingly .
T rip Functions Press and r elease the MENU button until one of the following T rip Functions displays in the EVIC: • A verage Fuel Economy / Fuel Saver Mode • Distance T o Empty • T rip A • T rip B • Elapsed T ime • Display Units of Measure in Press the SCROLL button to cycle through all the T rip Computer functions.
This feature allows you to monitor when the MDS switches off the fuel on four of the eight cylinders and it can be used to modify driving habits in order to incr ease the time in which the fuel saver mode is active. • Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank.
• Elapsed T ime Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or ST AR T position.
2. Press and hold the compass button for appr oximately 2 seconds. 3. Press the SCROLL button until “Calibrate Compass” displays in the EVIC. 4. Press and r elease the FUNCTION SELECT button to start the calibration. The message “CAL” will display in the EVIC.
1. T urn the ignition switch ON. 2. Press and hold the compass button for appr oximately 2 seconds. 3. Press the SCROLL button until “Compass V ariance” message and the last variance zone number displays in the EVIC. 4. Press and r elease FUNCTION SELECT button until the proper variance zone is selected accor ding to the map.
The EVIC displays this symbol to indicate that the UConnect™ phone is currently in analog mode. The EVIC displays this symbol to indicate that the UConnect™ phone is currently r oaming. The EVIC displays this symbol to indicate that you have voice mail.
Navigation — If Equipped Navigation Display Control Press and r elease the MENU button until Navigation displays in the EVIC. When the Navigation System is On, the steering wheel buttons can be used to select the Map or Menu display on the Navigation Unit.
“Lock Doors Automatically at 15 mph (24 Km/h)” When ON is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). T o make your selection, press and r elease the FUNC- TION SELECT button until “ON” or “OFF” appears.
off if they wer e turned on by this feature. T o make your selection, press and r elease the FUNCTION SELECT button until “ON” or “OFF” appears. NOTE: T urning the headlights on during the daytime causes the instrument panel lights to dim. T o increase the brightness, refer to “Lights” in Section 3 of this manual.
“Display Units of Measure in” The EVIC, odometer , and navigation system (if equipped) can be changed between English and Metric units of measure. T o make your selection, press and release the FUNCTION SELECT button until “US” or “METRIC” appears.
NOTE: For vehicles not equipped with the Electronic V ehicle Information Center (EVIC), the radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for 10 minutes after the ignition switch is turned off.
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Pr ess the ON/VOL a second time to turn OFF the radio.
SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to sear ch for the next listenable station in either , AM, FM, or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, pr ess SCAN a second time.
Press the r otary TUNE control a second time and MID will display . T urn the TUNE control to the right or left to increase or decr ease the Mid Range tones. Press the r otary TUNE control a third time and TREB will display . T urn the TUNE control to the right or left to increase or decr ease the T reble tones.
Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display .
TIME Button (CD Mode) Press this button to change the display fr om elapsed CD playing time to time of day . The time of day will display for 5 seconds. R W/FF (CD Mode) Press and hold the FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased.
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound fr om the speakers. ⬙ MUTE ⬙ will display . Press the MUTE button a second time and the sound from the speakers will r eturn. Rotating the volume control or turning OFF the ignition will also return the sound fr om the speakers.
SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAP ABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection.
AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the r otary TUNE control and BASS will display . T urn the TUNE control to the right or left to increase or decrease the Bass tones. Press the r otary TUNE control a second time and MID will display .
Soft Rock Soft_Rock T op 40 T op_40 Country Country Oldies Oldies Soft Soft Nostalgia Nostalgia Jazz Jazz Classical Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Soft_R_&_B For.
Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the curr ent selection. Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc.
Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. T o turn off the Dolby Noise r eduction System: Press Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is of f.
SCAN Button (CD MODE for CD Audio Play) Press the Scan button to scan thr ough each track on the CD currently playing. LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/EJECT - Load Press the LOAD/EJT button and the push- button with the corresponding number wher e the CD is being loaded.
R W/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . TUNE Control (CD MODE for CD Audio Play) Pressing the TUNE contr ol allows the setting of the T one, Fade, and Balance.
The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ .
Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3 and WMA Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
LOAD/EJT - Eject Press the LOAD/EJT button and the push- button with the corresponding number wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc.
T urn the TUNE control to display available folders or move through available folders. Pr ess the TUNE control to select a folder . Button s1-6( C DM o d ef o rM P 3 Play) Selects disc positions 1 - 6 for Play/Load/Eject. Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Phone” in Section 3 of the Owner’s Manual.
Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America. Refer to your “Navigation User’s Manual” for detailed operating instructions.
5. Select DONE to exit from the clock setting mode. Pr ess ENTER to save your changes. If you press CANCEL or NA V then your changes will not be saved. User Defined Clock If you wish to set the clock to a time differ ent than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option.
Audio Clock Display Select this option to change the size of the clock on the audio screens. 1. When you are at an audio scr een, quickly press the TIME button on the navigation faceplate. 2. In this example the large clock appears on the scr een. 3. T o switch the clock to the small clock, quickly press TIME again.
VIDEO ENTERT AINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (V ideo Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-power ed remote control, and two head- sets. The system is located in the center console storage bin under the armrest lid.
SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to r eceiver broadcast- ing technology to provide clear digital sound, coast to coast.
ESN/SID Access W ith REF Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and T ime buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will display . Press the SEEK UP button to display the next four digits.
A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and r elease the SEEK or TUNE knob to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down.
PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna T o ensure optimum r eception, do not place items on the roof ar ound the rooftop antenna location.
The VOLUME button controls the sound level of the sound system. Press the top of the VOLUME button to increase the sound level. Press the bottom of the VOLUME button to decrease the sound level. Press the AUDIO MODE button to select the Compass/T emp/Audio screen.
T ape Player Operation Press the top of the SCROLL button once to listen to the next track on the cassette. Press the bottom of the SCROLL button once either to listen to the beginning of the current track or to listen to the beginning of the previous track if it is within 5 seconds after the curr ent track begins to play .
5. A loose tape should be corrected before use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
T emperature Control The rotary knob in the center contr ols air temperature. Rotate the contr ol to the left for cooler air temperature and to the right for warmer air tempera- ture. Rotating the contr ol to the ex- treme left pr ovides the coldest setting.
• Panel Air flows through the outlets located in the in- strument panel. Air flows through the registers in the back of the center console to the rear seat passen- gers. These registers can be closed to block airflow . • Recirculation Contr ol The mode control knob also contr ols the recir culation feature.
The controls on the climate contr ol provide the system with operator input. The dual sun-sensor monitors sun load coming through the windshield. The infrar ed sensor independently measures the surface temperatur e of the driver and passenger .
The system will automatically control r ecir- culation. However , pressing the Recir cula- tion Control button will temporarily put the system in recir culation mode (ten minutes). This can be used when outside conditions such as smoke, odors, dust, or high humidity are pr esent.
UNDERST ANDING YOUR INSTRUMENT P ANEL 185 4.
The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Contr ol knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield thr ough the outlets at the base of the windshield.
NOTE: T o control the air conditioning manually , the mode selector must be moved out of the AUTO position. • Recirculation Contr ol This button can be used to block out smoke, odors, dust, high humidity , or if rapid cooling is desired. The r ecirculation mode should only be used temporarily .
V acation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, r un the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting.
Control Setting Suggestions for V arious W eather Conditions UNDERST ANDING YOUR INSTRUMENT P ANEL 189 4.
REAR WINDOW FEA TURES Electric Rear Window Defroster The electric Rear W indow Defroster Control is located on the climate control. Pr ess this button to turn on the rear window defr oster and the heated side mirrors (if equipped). An LED in the button will illumi- nate when the rear window defr oster is ON.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 1 9 4 ▫ Automatic T ransmission ................ 1 9 5 ▫ Normal Starting ...................... 1 9 5 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ......
▫ Anti-Lock Brake System — If Equipped ..... 2 1 4 䡵 Power Steering ........................ 2 1 7 䡵 Multi Displacement System (MDS) - 5.7L Engine Only ...................... 2 1 8 䡵 T raction Control System (TCS) — If Equipped .... 2 1 8 䡵 Brake Assist System (BAS) — If Equipped .
▫ Premium System — If Equipped .......... 2 4 6 ▫ General Information ................... 2 4 9 䡵 Fuel Requirements ..................... 2 5 0 ▫ 2.7L Engine ......................... 2 5 0 ▫ 3.5L And 5.7L Engines .................. 2 5 0 ▫ Reformulated Gasoline .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle.
Automatic T ransmission The gear selector must be in the NEUTRAL or P ARK position before you can start the engine. Apply the brakes before shifting into any driving gear . Normal Starting Normal Starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal.
W ARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . • Do not attempt to push or tow your vehicle to get it started.
ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather . Connect the cord to a standard 1 10-1 15 volt AC electrical outlet with a grounded, thr ee-wire extension cord. The engine block heater cord is r outed under the hood on the driver side of the vehicle.
W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
The selector lever is automatically locked while in the P (Park) position. T o move the selector lever out of the P (Park) position, the brake pedal must be firmly depressed before the shift lock will r elease. Shift the selector lever to the desired position only when the engine is idling normally and the brake pedal is applied.
Brake/T ransmission Shift Interlock System This vehicle is equipped with a brake transmission shift interlock system (BTSI) that holds the selector lever in the P (Park) position when the ignition switch is in the LOCK position.
Gear Ranges P (Park) P (Park) supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P (Park) while the vehicle is in motion.
The following indicators should be used to ensure that you have engaged the selector lever into the P (Park) position: • When shifting into P (Park) move the lever all the way forward until it stops, and is fully seated. • Look at the shift indicator display on the instrument panel to ensure it is in the P (Park) position.
vehicle under heavy loading conditions (in hilly ter- rain, traveling into strong head winds, or while tow- ing heavy trailers. NOTE: • If the vehicle is started in cold temperatures, shifts into Overdrive may be delayed.
T orque Converter Clutch A feature designed to impr ove fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly dif fer- ent feeling or response during normal operation in high gear .
NOTE: Even if the transmission can be reset, we recommend that you visit a dealer at your earliest possible convenience. Y our dealer has diagnostic equip- ment to determine if the problem could r ecur . If the transmission cannot be reset, dealer service is requir ed.
When parking on a flat surface, place the gear selector in the P (Park) position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the gear selector in P (Park), other- wise the load on the transmission locking mechanism may make it difficult to move the selector out of park.
The engine may be started in this range. Use this range for starting your vehicle if it is moving or being towed. CAUTION! Coasting the vehicle, or driving for any other reason with selector lever in NEUTRAL can result in trans- mission damage. W ARNING! Do not coast in N (Neutral) and never turn off the ignition to coast down a hill.
NOTE: T o avoid overrevving the engine when the selector lever is moved in “D -” direction, the transmis- sion will not shift to a lower gear if the engine’s revolu- tions per minute (RPM) limit would be exceeded.
2. Move the selector lever to the P (Park) position. 3. T urn off the engine. 4. W ait approximately 10 seconds. 5. Restart the engine. 6. Move the selector lever to the desired range. If the problem is no longer detected, the transmission will return to normal operation.
Autostick 威 Operation By placing the selector lever in the D (Drive) position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift.
• Y ou can start out in first or second gear . The system will ignore attempts to upshift at too low of a vehicle speed. • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in second gear is helpful in snowy or icy conditions.
DRIVING ON SLIPPER Y SURF ACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the rear wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a dif ference in the surface traction under the rear (driving) wheels.
P ARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. W ARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage.
NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. W ARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
The electronic brake for ce distribution (EBD) prevents the rear wheels fr om over-braking and provides gr eater control of available braking for ces applied to the rear axle. When the vehicle is driven over 7 mph (1 1 km/h), you may also hear a slight clicking sound as well as some related motor noises.
W ARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interfer- ence can cause possible loss of anti-lock braking capability .
Brake Force Distribution (EBD) systems ar e not function- ing. Immediate repair to the ABS system is requir ed. POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces.
MUL TI DISPLACEMENT SYSTEM (MDS) - 5.7L Engine Only This feature of fers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills requir ed.
acceleration, ease up on the accelerator and apply as little throttle as possible. Be sur e to adapt your speed and driving to the prevailing r oad conditions. The TCS OFF button is located in the center of the instrument panel. T o turn OFF the TCS, momentarily press the button and the TCS Indicator Light will illumi- nate.
BRAKE ASSIST SYSTEM (BAS) — IF EQUIPPED W ARNING! The BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions.
ELECTRONIC ST ABILITY PROGRAM (ESP) — IF EQUIPPED W ARNING! The ESP (Electronic Stability Program) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
The ESP OFF button is located in the center of the instrument panel. T o turn OFF the ESP , momentarily press the ESP OFF button and the ESP/TCS Indicator Light will illuminate. T o turn the system ON again, momentarily press the ESP OFF button and the indicator light will turn OFF .
CAUTION! If the vehicle is towed with the front axle raised, the engine must be shut off (key in the ignition switch to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Synchronizing ESP The malfunction indicator light for the ESP is combined with BAS indicator .
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
ST ARTING AND OPERA TING 231 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation, also increases tire r olling resistance and results in higher fuel consump- tion.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pr essure.
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
SELF–SEALING TIRES — IF EQUIPPED A non-hardening viscous sealant applied to the inner liner of each tire fills punctur es up to 0.19 in. (5 mm) to minimize the loss of air pressur e. This contributes to the safety of the vehicle by significantly reducing the pr ob- ability of a roadside stop due to a flat tir e.
NOTE: In order to avoid damage to tir es, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufactur er’s instructions on method of installation, operating speed, and conditions for usage.
Follow the “Maintenance Schedules” in Section 8 of this manual for the recommended tir e rotation frequency for your type of driving. Remember , more fr equent rotation is permissible if desired. Also, correct for anything caus- ing rapid or unusual wear prior to performing the tire rotation.
• The TPM System will warn the driver of a low tire pressur e if the tire pressur e falls below the low- pressur e warning limit for any reason, including low temperature ef fects.
CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Base System — If Equipped The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pr essure readings to the Receiver Module.
NOTE: The compact spare tir e (if so equipped) does not have a tire pr essure monitoring sensor . Therefore, the TPMS will not monitor the pressur e in the compact spare tire.
T ire Pressure Monitoring Low Pressure W arnings The T ire Pressur e Monitoring T elltale Light will illuminate in the instrument cluster and an audible chime will sound when tire pr essure is low in one or more of the four active r oad tires. The audible chime will sound once every ignition cycle for each condition that it detects.
Check TPMS W arning The T ire Pressur e Monitoring T elltale Light will flash on and off for 60 seconds and an audible chime will sound when a system fault is detected. The flash cycle will repeat every ten minutes, without an audible chime, until the fault condition no longer exists.
NOTE: The compact spare tir e (if so equipped) does not have a tire pr essure monitoring sensor . Therefore, the TPMS will not monitor the pressur e in the compact spare tire.
FUEL REQUIREMENTS 2.7L Engine Y our vehicle is designed to meet all emis- sions regulations and pr ovide satisfactory fuel economy and performance when us- ing high quality unleaded gasoline having an octane of 87. 3.5L and 5.7L Engines The 3.5L and 5.
Reformulated Gasoline Many areas of the country r equire the use of cleaner burning gasoline referr ed to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality .
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber . Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT .
• The use of fuel additives, which are now being sold as octane enhancers, are not r ecommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting fr om the use of such fuels or additives are not the responsibility of the manufactur er .
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. Push in on the left side (near the edge) of the fuel filler door to access the fuel filler cap. If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle.
CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunc- tion Indicator Light to turn on.
• When the fuel nozzle “clicks” or shuts off, the fuel tank is full. Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC) — if equipped.
• V ehicle Identification Number (VIN) • T ype of V ehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the V ehicle Identification Number (VIN). Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.
Figure out the weight on the fr ont and rear of the vehicle separately . It is important that you distribute the load evenly over the front and r ear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
NOTE: Refer to the “V ehicle Certification Label” at- tached to the rear of the driver’s door for your vehicle’s GVWR and GA WRs. This table is only an example. TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
W ARNING! It is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident. T ongue W eight (TW) T ongue weight (TW) is the downward for ce exerted on the hitch ball by the trailer .
W ARNING! • An improperly adjusted W eight Distributing Hitch system may reduce handling, stability , braking performance, and could result in an accident.
T railer Hitch Classification Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 2.7L Automatic 22 SQ.
NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight refer enced on the “T ire and Loading Information” placard. Refer to “T ire–Safety Information” in this section.
must be considered as part of the total load on your vehicle. Refer to the “T ire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
• V ehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. Always, block or ⬙ chock ⬙ the trailer wheels. • GCWR must not be exceeded.
T owing Requirements — T railer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer . This could cause inadequate braking and possible personal injury . − An electronically actuated trailer brake contr oller is requir ed when towing a trailer with electronically actuated brakes.
T owing Requirements — T railer Lights & W iring Whenever you pull a trailer , regar dless of the trailer size, stop lights and turn signals on the trailer are r equired for motoring safety . The T railer T ow Package may includ ea4a n d7p i n wiring harness.
T owing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away fr om heavy traffic. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “3” range should be selected.
high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. T owing T ips — Cooling System T o reduce potential for engine and transmission over - heating, take the following actions: − City Driving When stopped for short periods, put transmission in neutral and increase engine idle speed.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................. 2 7 2 䡵 If Y our Engine Overheats ................ 2 7 2 䡵 Jacking And T ire Changing ............... 2 7 4 ▫ Preparations For Jacking ................ 2 7 4 ▫ Jack Location/Spare T ire Stowage .
HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel below the center air outlets. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel.
NOTE: There ar e steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
JACKING AND TIRE CHANGING W ARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous.
5. Passengers should not remain in the vehicle when the vehicle is being jacked. 6. Block both the front and r ear of the wheel diagonally opposite the jacking position.
4. Remove the spare tir e. 5. Remove the fastener securing the jack. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided.
Jacking and Changing a Tire 1. Block the wheel diagonally opposite the flat tire. Passengers should not remain in the vehicle when the vehicle is being jacked. 2. Remove the spare tir e, jack, and lug wrench. 3. If equipped with steel wheels, do not remove the wheel cover at this time.
4. Before raising the vehicle, use the lug wr ench to loosen, but not remove, the lug nuts on the wheel with the flat tire. T urn the lug nuts counter -clockwise one turn while the wheel is still on the ground. 5. Place the jack underneath the lift area that is closest to the flat tire.
Jack Engagement Locations WHA T TO DO IN EMERGENCIES 279 6.
6. Raise the vehicle just enough to remove the flat tir e and install the spare tir e. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
Wheel Cover Installation (If Required) 1. T ighten the two lug nuts on the mounting studs on each side of the stud which is in alignment with the valve stem. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. 3. Install the cover by hand, snapping the cover over the two lug nuts.
JUMP-ST ARTING PROCEDURES W ARNING! • T ake care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. Y ou can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started.
5. Connect one end of the jumper cable to the remote jump-start positive battery post (+) in the engine com- partment. Connect the other end of the same cable to the positive terminal of the booster battery . Refer to the following illustration for jump-starting connections.
8. When removing the jumper cables, r everse the above sequence exactly . Be careful of the moving belts and fan. W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3.
CAUTION! • When “rocking” a stuck vehicle by moving be- tween “First” and R (Reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure.
km/h). Exceeding these towing limits may cause a trans- mission geartrain failure. If the transmission is not op- erative, or if the vehicle is to be towed more than 30 miles (48 km), the vehicle must be transported using a flat bed truck. CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.7L Engine Compartment ............... 2 8 9 䡵 3.5L Engine Compartment ............... 2 9 0 䡵 5.7L Engine Compartment ............... 2 9 1 䡵 Onboard Diagnostic System — OBD II ...... 2 9 2 ▫ Loose Fuel Filler Cap .
▫ Body Lubrication ..................... 3 0 6 ▫ W indshield W iper Blades ................ 3 0 6 ▫ W indshield W ashers ................... 3 0 7 ▫ Exhaust System ...................... 3 0 7 ▫ Cooling System ....................... 3 0 8 ▫ Hoses And V acuum/V apor Harnesses .
2.7L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 289 7.
3.5L ENGINE COMP ARTMENT 290 MAINT AINING YOUR VEHICLE.
5.7L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 291 7.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC) — if equipped.
5. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn of f the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. Checking Oil Level — 5.7L Engine T o assure pr oper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affect the interval at which your oil should be changed. Check the following list to see if any apply to you.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only r ecommends API Certified engine oils. Engine Oil V iscosity (SAE Grade) — 2.
The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Com- partment” illustration in this section. In areas wher e these grades are not generally available, higher SAE grades may be used.
Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter . Use a filter of this type for replacement. The quality of replacement filters varies considerably .
W ARNING! The air induction system (air cleaner , hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc) unless such removal is necessary for repair or maintenance.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system.
Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is perma- nently sealed. Y ou will never have to add water , nor is periodic maintenance requir ed. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals ar e located in the engine compartment for jump starting.
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and identified on the battery case.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor ocar- bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product.
If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
Windshield W ashers The windshield washer fluid reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level at r egular intervals.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breath- ing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Exhaust Gas” in the “Safety T ips” section of this manual.
Cooling System — Drain, Flush, and Refill The system should be drained, flushed, and refilled at the intervals shown on the Maintenance Schedules. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Y ears or 100,000 miles (160 000 km) before r eplacement. T o prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Points T o Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the fr ont of the engine compartment.
Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sur e hoses do not come in contact with any heat source or moving component which may cause heat damage or mechanical wear . Insure nylon tubing in these ar eas has not melted or collapsed.
Brake And Power Steering Hoses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle r ubber , cracking, tears, cuts, abrasion, and excessive swelling indicate deterioration of the rubber .
Master Cylinder — Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area befor e removing the cap.
Automatic T ransmission Fluid Level Check Regular automatic transmission fluid level checks are not requir ed. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
Fluid and Filter Changes Automatic transmission fluid and filter should be changed as follows: Normal Usage — No change necessary Severe Usage (fluid and filter) — Refer to Maintenance Schedule .
Fluid Changes The fluid should be changed as follows: Normal Usage Front Dif ferential No Service Required T ransfer Case Refer to Maintenance Schedule “A” Severe Usage Front Dif ferential No Service Required T ransfer Case Refer to Maintenance Schedule “B” Severe Usage is defined as: 1.
What Causes Corrosion? Corrosion is the r esult of deterioration or removal of paint and protective coatings fr om your vehicle. The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the r esponsibility of the owner . • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and pr otective coating, have your vehicle repair ed as soon as pos- sible.
and Mopar 威 T otal Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery .
1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners.
FUSES (POWER DISTRIBUTION CENTERS) Fuses (Front Power Distribution Center) A power distribution center is located in the engine compartment. This center contains fuses and relays.
Cavity Car- tridge Fuse Mini Fuse Description 1 1 — 25 Amp Clear Auto Shutdown/ Powertrain Control Module (PCM) 1 2——— 1 3——— 14 — 25 Amp Clear Powertrain Control Module (PCM) 15 — 2.
CAUTION! • When installing the Power Distribution Center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Power Distribu- tion Center , and possibly result in an electrical system failure.
Cavity Car- tridge Fuse Mini Fuse Description 1 60 Amp Y ellow — Ignition Off Draw (IOD) 2 40 Amp Green — Battery 3— — — 4 40 Amp Green — Battery Cavity Car- tridge Fuse Mini Fuse Descript.
Cavity Car- tridge Fuse Mini Fuse Description 17 — 20 Amp Y ellow Cluster 18 — 20 Amp Y ellow Selectable Power Outlet 19 — 10 Amp Red Stop Lights 2 0——— 2 1——— 2 2——— 2 3——.
Cavity Car- tridge Fuse Mini Fuse Description 35 — 5 Amp Orange Amplifier - if equipped/ Antenna/Ignition Delay/Overhead Console/Passenger Door Lock & Express Power W indow Switch - if equipped/.
(base), the Driver Express Power W indow Switch (if equipped), and the Passenger Door Lock Switch (base) are fused by the 25 amp cir cuit breaker in Cavity 13. If you experience temporary or permanent loss of these systems, see your authorized dealer for service.
REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights .............. W 5 W Rear Compartment (T runk) Light ............. 5 6 2 Overhead Console Reading Lights ............. 5 7 8 V isor V anity Lights ..............
BULB REPLACEMENT Low Beam Headlight, High Beam Headlight, Park/T urn Light, and Front Side Marker Light 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the headlight assem- bly on the driver side of the vehicle.
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
Backup Light, Side Marker Light, T ail/T urn Light, and T ail/Stop Light 1. Open the T runk. 2. Remove two fasteners from the back of the tail light assembly . 3. Pull back the trunk liner . 4. Remove the remaining fastener fr om the back of the tail light assembly .
7. Pull the tail light assembly clear from the vehicle to access the bulbs. 8. T urn the appropriate bulb and socket assembly counter-clockwise to r emove it from the tail light assem- bly .
9. Pull the bulb out of the socket assembly . 10. Push the replacement bulb into the socket assembly . 1 1. Reinstall the bulb and socket assembly into the tail light assembly , and then turn it clockwise. 12. Reinstall the tail light assembly , fasteners, electrical connector , and trunk liner .
License Light 1. Remove the screws securing the light to the r ear fascia. 2. Remove the bulb and socket assembly . 3. Pull the bulb out of the socket assembly . 4. Push the replacement bulb into the socket assembly . 5. Reinstall the bulb and socket assembly .
FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 2.7 Liter Engine 18 gallons 68 liters 3.5 Liter Engine 18 gallons 68 liters 5.7 Liter Engine 19 gallons 72 liters Engine Oil-W ith Filter 2.7 Liter Engine (SAE 5W -20, API Certified) 6.0 qts. 5.7 liters 3.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluids, Lubricants, and Genuine Parts Engine Coolant Mopar 威 Antifr eeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil (2.7 Liter) Use API Certified engine oil.
Chassis Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid. Brake Master Cylinder Mopar 威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 3 4 2 䡵 Maintenance Schedules .................. 3 4 2 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather , above 90°F (32°C). • T railer towing. 〫 • T axi, police, or delivery service (commercial ser - vice).
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
SCHEDULE “B” Follow Schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 .
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XXXX X Replace the air cleaner filter .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (1 10 000) (1 15 000) (120 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 108,000 11 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
SCHEDULE “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) (60 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Inspect the air cleaner filter and replace if r e- quired.
Miles 42,000 48,000 54,000 60,000 66,000 72,000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (1 10 000) (120 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X X X X X Inspect the air cleaner filter and replace if requir ed.
Miles 78,000 84,000 90,000 96,000 102,000 (Kilometers) (130 000) (140 000) (150 000) (160 000) (170 000) [Months] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.* XX X X Replace the air cleaner filter .
Miles 108,000 1 14,000 120,000 126,000 132,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) [Months] [108] [1 14] [120] [126] [132] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.
Miles 138,000 144,000 150,000 (Kilometers) (230 000) (240 000) (250 000) [Months] [138] [144] [150] Change engine oil and engine oil filter . X X X Inspect the air cleaner filter and replace if r equired.* X X Replace the air cleaner filter . X Inspect the front and r ear brake linings and rotors.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle ....................... 3 6 2 ▫ Prepar e For The Appointment ............ 3 6 2 ▫ Prepar e A List ........................ 3 6 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
• If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center .
Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs after your manufactur er’s new vehicle limited warranty expires. The manufactur er stands be- hind only the manufacturer’s Service Contracts.
REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer .
Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, dia- grams, and charts.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under contr olled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10.
ABS (Anti-Lock Brake System) ............. 2 1 4 Adding Engine Coolant (Antifreeze) ......... 3 1 0 Adding Fuel .......................... 2 5 4 Adding W asher Fluid ................. 102,307 Adjustable Pedals ....................... 1 0 4 Air Cleaner , Engine (Engine Air Cleaner Filter) .
Fluid Level Check ..................... 3 1 6 Fluid T ype .......................... 3 3 9 Gear Ranges ......................... 2 0 1 Shifting .......................... 200,205 Special Additives ..................... 3 1 7 T orque Converter ........
Cellular Phone .......................... 6 9 Chains, T ire ........................... 2 4 0 Changing A Flat T ire .................... 2 7 4 Chart, T ire Sizing ....................... 2 2 5 Check Engine Light (Malfunction Indicator Light) .........
Delay (Intermittent) W ipers ............... 1 0 1 Diagnostic System, Onboard ............... 2 9 2 Dimmer Switch, Headlight ................. 9 8 Disposal Antifreeze (Engine Coolant) ............. 3 1 1 Door Locks ............................ 2 3 Door Locks, Automatic .
Enhanced Accident Response Feature ......... 4 8 Ethanol .............................. 2 5 1 Event Data Recorder ..................... 4 9 Exhaust Gas Caution ............... 60,253,308 Exhaust System ...................... 60,307 Exterior Folding Mirrors .
Requirements ..................... 250,337 T ank Capacity ........................ 3 3 7 Fuel System Caution .................... 2 5 5 Fueling .............................. 2 5 4 Fuses ................................ 3 2 3 Garage Door Opener (HomeLink 威 ) .
Ignition ............................... 1 1 K e y ................................ 1 1 Ignition Key Removal .................... 1 1 Illuminated Entry ....................... 1 7 Immobilizer (Sentry Key) .................. 1 3 Infant Restraint ......
Bulb Replacement ..................... 3 3 0 Courtesy/Reading .................. 99,108 Cruise ............................. 1 2 9 Daytime Running ...................... 9 7 Dimmer Switch, Headlight ............... 9 8 Electronic Stability Pr ogram (ESP) Indicator .
Lower Anchors and T ether for CHildren (LA TCH) .................... 54,55 Lubrication, Body ....................... 3 0 6 Lumbar Support ........................ 9 0 Maintenance Free Battery ................. 3 0 3 Maintenance Procedur es ...........
Materials Added to .................... 2 9 9 Recommendation .................. 297,337 Synthetic ........................... 2 9 9 V iscosity ......................... 298,337 Onboard Diagnostic System ............ 292,293 Opener , Garage Door (HomeLink 威 ) .
Radio Operation .................. 150,157,180 Radio Remote Controls .................. 1 7 6 Radio, Satellite ...................... 169,173 Radio (Sound Systems) ................ 150,157 Rear Seat, Folding ....................... 9 3 Rear W indow Defroster .
Untwisting Procedur e ................... 3 9 Seats ................................. 8 8 Adjustment .......................... 8 8 Heated .............................. 9 1 Lumbar Support ....................... 9 0 Power ............................
Storage, V ehicle ..................... 188,329 Storing Y our V ehicle ..................... 3 2 9 Sun Roof ............................. 1 1 4 Sunglasses Storage ...................... 1 0 9 Supplemental Restraint System - Airbag ....... 4 2 Synthetic Engine Oil .
T ongue W eight/T railer W eight ............. 2 6 4 T orque Converter Clutch ................. 2 0 4 T owing .............................. 2 5 9 Behind a Motor Home ................. 2 7 0 Disabled V ehicle ...................... 2 8 5 Guide .......
V ehicle Loading .................. 229,256,258 V ehicle Modifications/Alterations ............ 7 V ehicle Storage ...................... 188,329 V ehicle Theft Alarm (Security Alarm) ......... 1 5 V ideo Entertainment System (Rear Seat V ideo System) .
An important point after buying a device Dodge 2007 LX Charger (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dodge 2007 LX Charger yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dodge 2007 LX Charger - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dodge 2007 LX Charger you will learn all the available features of the product, as well as information on its operation. The information that you get Dodge 2007 LX Charger will certainly help you make a decision on the purchase.
If you already are a holder of Dodge 2007 LX Charger, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dodge 2007 LX Charger.
However, one of the most important roles played by the user manual is to help in solving problems with Dodge 2007 LX Charger. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dodge 2007 LX Charger along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
