Instruction/ maintenance manual of the product 2006 Durango Dodge
Go to page of 440
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ......
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 0 ▫ Key-In-Ignition Reminder ................ 1 0 ▫ Sentry Key — If Equipped ................ 1 0 䡵 Ignition And Steering Lock ...........
䡵 Security Alarm System — If Equipped ......... 2 6 ▫ T o Set The Alarm ...................... 2 7 ▫ T o Disarm The System ................... 2 7 䡵 Remote Starting System — If Equipped ........ 2 8 䡵 Liftgate ...........................
▫ Exhaust System ....................... 7 5 ▫ Safety Checks Y ou Should Make Inside The V ehicle .............................. 7 6 ▫ Safety Checks Y ou Should Make Outside The V ehicle .
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith.
on the remaining transmitters will work. If the vehicle is moving 5 mph or more, then all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting pr oblems and a loss of security protection.
consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1.
NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to pr ovide anti-theft protection for your ve- hicle.
W ARNING! The key cannot be turned to LOCK until the selector is in the P ARK position. Do not attempt to pull the shift lever out of P ARK after the key is in the LOCK position.
DOOR LOCKS Manual Door Locks All the doors can be “manually” locked from the inside by pushing down the door lock plunger , located at the rear of the door . Both front doors may be opened fr om the inside with the door lock plunger in the down or locked position.
Power Door Locks V ehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pr essing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
occur only after the vehicle has been shifted into the Park position after the vehicle has been driven (shifted out of Park and all doors closed). This feature will not operate if ther e is any manual operation of the power door locks (Lock or Unlock).
Child Protection Door Lock T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
NOTE: Y our vehicle’s keyfob may have three, four or five buttons (shown), depending on the optional features purchased with your vehicle. This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter .
5. If the desired programming was not achieved or to reactivate this featur e, repeat the above steps. T o lock the doors and liftgate: Press and r elease the LOCK button on the key fob to lock all doors and liftgate. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Flash Lamps with Lock Programming 1. Press and hold the UNLOCK button on the key fob. 2. After holding the UNLOCK button for four seconds, also press the LOCK button within 6 seconds. A single chime will sound to indicate that this feature has changed.
General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interfer ence that may cause undesired operation.
2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this program- ming procedur e). 3. Place the key into the ignition. 4. T urn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on the key fob.
Battery Replacement The recommended r eplacement battery is CR2032. 1. If the key fob is equipped with a screw , remove the screw . W ith the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal.
T o Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming.
UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position. REMOTE ST ARTING SYSTEM — IF EQUIPPED Y our Dodge Durango may be equipped with a remot.
T o enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. After the vehicle is unlocked, you have 60 seconds to.
NOTE: When the engine is running fr om a Remote Start (if equipped), the vehicle must first be unlocked by pressing the keyfob UNLOCK button prior to activating the Power Liftgate otherwise the engine will stop auto- matically . Once unlocked, the liftgate can be opened or closed.
Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter . Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate.
W ARNING! During power operation, personal injury or cargo damage may occur . Ensure the liftgate travel path is clear . Make sure the liftgate is closed and latched before driving away . A beeping signal will sound two seconds before the liftgate starts to open or close.
(65° C). Be sure to r emove any buildup of snow or ice from the liftgate befor e pressing any of the power liftgate switches. • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually .
WINDOWS Power Windows The control on the left fr ont door has up-down switches that give you finger tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control.
ignition is turned OFF or the driver’s door is opened. This feature can be turned of f by your authorized dealer . NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF . Auto Down The driver’s window switch has an Auto Down feature.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, knee bolsters.
of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt buckled into the wrong buckle will not protect you properly .
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in the desired position.
Rear 60/40 Seat Third Row Center Three Point Belt — If Equipped The center three point seat belt for the thir d row r ear seat may be disconnected to allow the 60% seat back to easily fold down.
T o reattach the seat belt to the thir d row center seat, pull the small (keyed buckle) latch plate forward fr om the headliner slots and insert it into the keyed buckle until there is an audible click. Refer to the pr evious section for the proper seat belt usage.
Seat Belt Pretensioners The seat belts for both front seating positions ar e equipped with pretensioning devices that ar e designed to remove any slack fr om the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert) will alert the driver to buckle their seat belt.
buckled. A chime will sound immediately (once the feature has toggled). If during this time the ignition switch is turned out of the ON position or the timer expires, pr ogramming mode will be cancelled.
W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
the instrument panel, above the glove compartment. The words SRS/AIRBAG ar e embossed on the airbag covers. NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design.
Along with the seat belts, front airbags work with the instrument panel knee bolsters to pr ovide improved protection for the driver and fr ont passenger . W indow bags also work with seat belts to improve occupant protection. The seat belts are designed to pr otect you in many types of collisions.
4. If your vehicle has window bags, do not lean against the door or window , airbags will inflate forcefully into the space between you and the door . 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center .
Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag W arning Light • Driver Airbag .
The ORC also monitors the readiness of the electr onic parts of the system whenever the ignition switch is in the ST AR T or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appr opriate child restraint. • The Passenger Airbag Disable (P AD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned of f.
adult passenger is properly seated in the fr ont passen- ger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs.
will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
sensors, a fault will occur which turns on both the P AD Indicator Light and the Airbag W arning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time.
• The Side Impact SRS W indow Bags are designed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag.
• Do not replace the seat cover with an aftermarket seat cover . • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar .
NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
• The light flickers or comes on and remains on while driving. NOTE: If the speedometer , tachometer or any engine related gauges ar e not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection.
may be released for incorporation in aggr egate crash databases, such as those maintained by the US govern- ment and various states. Data of a potentially sensitive nature, such as would identify a particular driver , ve- hicle, or crash, will be treated confidentially .
Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it.
LA TCH child restraint anchorage system. (See the LA TCH - Child Seat Anchorage System section.) • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a fr ont passenger airbag. An airbag deployment could cause severe injury or death to infants in this position.
• If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. W ARNING! • Improper installation can lead to failure of an infant or child restraint.
lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however , any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary . If the seat belt has a automatic locking retractor , it will have a distinctive label.
restraints, many child r estraint manufacturers of fer add-on tether strap kits or retr o-fit kits. Y ou are ur ged to take advantage of all the available attachments provided with your child restraint in any vehicle.
Installing the LA TCH-Compatible Child Restraint System W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that were pr ovided with the child restraint system.
and some rear -facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Second Row Seat T ether Anchors 72 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE.
Child Restraints in Third Row Seating (If Equipped) The third seating r ow is not capable of installing child restraints that r equire the use of a tether strap. Ther e are no tether anchor provisions for the thir d seating row in your vehicle, the hooks in the rear floor ar e not designed to withstand the forces that may occur during a crash.
W ARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of dif ficulty . SAFETY TIPS Exhaust System W ARNING! Exhaust gases contain carbon monoxide, an ex- tremely toxic gas that by itself is colorless and odorless.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.
Fluid Leaks Check the area under vehicle after overnight parking for fuel, water , oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 8 4 ▫ Inside Day/Night Mirror ................. 8 4 ▫ Automatic Dimming Mirror — If Equipped .... 8 4 ▫ Outside Mirrors ....................... 8 5 ▫ Exterior Mirrors Folding Featur e — If Equipped .
䡵 Seats ................................ 1 1 1 ▫ Front Seat Manual Seat Adjustment ........ 1 1 1 ▫ Front Seats Manual Seat Recliners .......... 1 1 2 ▫ Manual Lumbar Support Adjustment — If Equipped ........................... 1 1 3 ▫ Adjustable Head Restraints — All Seating Positions .
▫ Automatic Headlights — If Equipped ....... 1 3 3 ▫ Headlights, Parking Lights, Panel Lights ..... 1 3 4 ▫ Illuminated Entry ..................... 1 3 4 ▫ Daytime Running Lights (Canada Only) ..... 1 3 4 ▫ Lights-On Reminder .............
䡵 Electronic Brake Contr ol System ............ 1 4 6 ▫ ABS (Anti-Lock Brake System) ............ 1 4 6 ▫ BAS (Brake Assist System) – If Equipped W i t h E S P ........................... 1 4 7 ▫ TCS (T raction Control System) – If Equipped W i t h E S P .
▫ Canadian Pr ogramming/Gate Programming . . 166 ▫ Using HomeLink ..................... 1 6 6 ▫ Erasing HomeLink Buttons .............. 1 6 6 ▫ Reprogramming a Single HomeLink Button . . . 167 ▫ Security ............................ 1 6 7 䡵 Power Sunroof — If Equipped .
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the r ear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of truck).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Electric Remote-Control Mirrors The controls for the power mirr ors are located on the driver’s door trim panel. T o adjust a mirror , turn the control wand toward the left or right mirror positions indicated. T ilt the control wand in the direction you want the mirr or to move.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror .
that the heating elements are ON. T urning Of f the rear window defroster or the ignition will deactivate the heated mirrors. Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare fr om vehicles behind you.
that enables differ ent electronic devices to connect to each other without wires or a docking station, so UCon- nect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system.
Headset Profile), you may not be able to use any UCon- nect™ features. Refer to your cellular service pr ovider or the phone manufacturer for details.
V oice Command T ree Refer to “V oice T ree” at the end of this section. Help Command If you need assistance at any prompt or if you want to know what your options are at any pr ompt, say ⬙ Help ⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help.
The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • When prompted, after the voice on beep, say ⬙ Pair a Phone.
Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙ 234-567-8901. ⬙ The phone number that you enter must be of valid length and combination.
Add Names to Y our UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook New Entry . ⬙ • When prompted, say the name of the new entry .
• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing.
• After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager . Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be de- leted.
Phone Call Features The following features can be accessed thr ough the UConnect™ system if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the UConnect™ system.
second call is in progr ess. T o go back to the first call, refer to ⬙ T oggling Between Calls. ⬙ T o combine two calls, refer to ⬙ Conference Call. ⬙ Place/Retrieve a Call from Hold T o put a call on hold, press the ⬘ Phone’ button until you hear a single beep which will indicate that the call has been placed on hold.
Redial • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ sys- tem.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. T owing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ T owing Assistance.
When calling a number with your UConnect™ system that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es).
Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc.
Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously pair ed to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin.
⬘ V oice Recognition’ button anytime while the list is being played and say the priority number of the phone you wish to delete. Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking.
• UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
108 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 109 3.
1 10 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
T o lower the head restraint, depr ess the release button located at the base of the head restraint and push down on the head restraint. 8 - W ay Driver’s Power Seat — If Equipped The driver power seat switches are located on the left side of the driver seat lower side trim.
4 - W ay Passenger’s Power Seat — If Equipped The front passenger’s power seat switches ar e located on the right side of the passenger seat lower side trim. The bottom switch controls forwar d/rearwar d adjustment. The top switch controls the seatback r ecline adjustment.
passenger to select from two dif ferent levels of supple- mental electrical seat heating, or no seat heating to suit their individual comfort requir ements.
W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
be folded into the down position for use as a cargo floor , or the seat can now be tumbled forward to allow access to the rear of the vehicle. T o fold the 20% seatback, pull the strap forward to r elease the seatback. Fold the seatback down for use as an armrest or to carry car go.
W ARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position. The outer 40% second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury .
Third Row Seat Bench — If Equipped T o Fold The Seats Folding the third seat occurs in two stages: First the cushion is lifted and moved forward fr om the pockets at the front of the cushion. The cushion will r est onto the floor directly behind the second r ow seat.
T o Achieve Maximum Cargo Capacity Pull the release handles and strap on the second r ow seats and fold flat. After folding the third row seat, unsnap the flipper panel on the third r ow seatback and flip it forward on the backs of the second r ow seats.
NOTE: Before r eturning the second row 40% seats to their upright position, always snap the third r ow seat flipper panel(s) back to the third r ow seat first. NOTE: The seat belt buckles are hinged to fold with the seat back. W ARNING! Do not sit in the third row seat unless the cushion and back are properly engaged.
Third Row Seat 40% Seatback Folded Down Third Row Seat Features UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 123 3.
Third Row Seat Folded Forward Third Row Seat Return Pull Strap 124 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
DRIVER MEMOR Y SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic T em- perature Contr ol (A TC) temperature and radio station preset settings.
Setting Memory Positions and Linking Remote Keyless Entry T ransmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pr essed, you erase the memory settings for that button and store new settings. 1. Adjust the driver’s seat, recliner , and both side view mirrors to the desir ed positions.
Memory Position Recall NOTE: • The driver’s seat belt must be unbuckled to recall memory positions. • The vehicle must be in Park to recall memory posi- tions. • Not all motors may be moved at one time. Please refer to the 8-way power seat description.
3. W ithin 10 seconds, press and r elease the UNLOCK button on the Remote Keyless Entry transmitter . T o disable another transmitter linked to either memory position, repeat steps 1-3 for each transmitter . NOTE: The capability to link Remote Keyless Entry transmitters to memory is enabled when delivered fr om the factory .
the seat is positioned rearwar d enough and no benefit from moving the seat any farther r earward. NOTE: The Easy Exit Easy Entry feature is not enabled when delivered fr om the factory . The Easy Exit Easy Entry feature may be enabled (or later disabled) by a qualified DaimlerChrysler service repr esentative.
Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center . T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center fr ont edge of the hood to ensure that both latches engage.
LIGHTS UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 131 3.
Interior Lights Courtesy and dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or when the UNLOCK button is pressed on the key fob.
If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn of f after 8 minutes. If the headlights are turned on and left on for 8 minutes while the ignition is off, the exterior lights will automatically turn off.
Headlights, Parking Lights, Panel Lights When the headlight switch is rotated to the first position to the right, the parking lights, taillights, side marker lights, license plate light and instrument panel lights ar e all turned on. The headlights will turn ON when the switch is rotated to the second position.
Lights-on Reminder If the headlights, parking lights, or courtesy lights are left On, after the ignition is turned Off, a continuous fast chime will sound when the driver’s door is opened.
T urn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instr ument cluster flashes to indicate the direction of the turn, and pr oper operation of the front and r ear turn signal lights.
High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever .
with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the contr ol knob into the upper end of the delay range. The delay interval decreases as you r otate the knob until it enters the LO continual speed position.
Windshield W ashers T o use the washer , push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depr essed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
deep snow , sand, or gravel turn the system Off to improve traction. If the vehicle is 4WD, use 4HI position. When the ESP is switched of f, the ESP/TCS Indicator light in the instrument cluster comes on. When the ESP is switched on, the Indicator light goes out.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2.
T o Activate Push the ON/OFF button to the ON position. In the instrument cluster , the word “CRUISE” illuminates when the system is on. T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed.
W ARNING! Leaving the Speed Control ON when not in use is dangerous. Y ou could accidentally set the system to cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you aren’t using it. T o Resume Speed T o resume a pr eviously set speed, push and release the RESUME button.
Functions 3.7L 4.7L 5.7L Engage Speed 35 mph (56 km/h) 35 mph (56 km/h) 25 mph (40 km/h) Minimun RESUME Speed 30 mph (50 km/h) 30 mph (50 km/h) 20 mph (32 km/h) ACCEL Increase 2 mph (3km/h) 2 mph (3km.
W ARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Y our vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery .
W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
applies optimum pressur e to the brakes. The system applies optimum pressur e to the brakes in emergency braking conditions. This can help reduce braking dis- tances. The BAS complements the antilock brake system (ABS). Applying the brakes very quickly results in the best BAS assistance.
TCS (T raction Control System) – if equipped with ESP This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressur e is applied to the slipping wheel(s) and engine power is reduced to pr ovide enhanced acceleration and stability .
W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur . • ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
• Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP/TCS Indicator Light The ⬙ ESP/TCS Indicator Light ⬙ starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ ESP/TCS Indicator Light ⬙ also flashes when TCS is active.
High Range (4WD Models) or 2WD Models ON This is the normal operating mode for ESP in 4WD high range and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD low range or neutral back to 4WD high range, the ESP system will be in this mode.
situation requiring ESP to be switched to the “Partial Of f” mode is overcome, turn ESP on by momentarily depress- ing the “ESP Contr ol Switch”. This may be done with the vehicle is in motion. 4WD Low Range Partial Of f This is the normal operating mode for ESP in 4WD low range.
W ARNING! In the Partial Off mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP/BAS W arning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator .
OVERHEAD CONSOLE The overhead console has the following featur es: • Courtesy Lights • Garage Door Opener — If Equipped • Compass/T emperature Mini-T rip Computer — If Equipped Courtesy/Reading Lights Near the front of the console ar e two courtesy/reading lights.
COMP ASS/TEMPERA TURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of four trip conditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units.
Global Reset If the RESET button and STEP button ar e pressed at the same time and held for 3 seconds (you will hear a confirmation beep) and the Global Reset feature will r eset the distance to empty (using a default fuel economy value), fuel economy , trip odometer , and elapsed time displays.
A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset incr eases.
C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. Compass/T emperature Display W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges.
After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area fr ee from lar ge metal or metallic objects, the CAL symbol will turn off and the compass will function normally .
T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
GARAGE DOOR OPENER — IF EQUIPPED The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver . Exhaust gas can cause seri- ous injury or death. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light (dots below House Symbol) in view . 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons.
constantly , programming is complete and your device should activate when the HomeLink button is pressed and released. NOTE: T o program the r emaining two HomeLink but- tons, begin with ⬙ Programming ⬙ step two.
Canadian Programming/Gate Programming Canadian radio-frequency laws r equire transmitter sig- nals to ⬙ time-out ⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law , some U.
• Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙ Programming ⬙ - step 2.
• This device must accept any interference that may be received including interfer ence that may cause undes- ired operation. NOTE: Changes or modifications not expressly ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment.
condition until the switch is pushed forward again. T o close fully , hold the switch in the forward position until the glass movement has stopped. The sunshade can be opened manually . It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open.
the rear windows open, open the fr ont and rear windows together to minimize the buffeting. If the buf feting occurs with the sunroof open, adjust the sunr oof opening to minimize the buffeting or open any window . Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
NOTE: The fuse block is located in the left side kick panel behind a removable cover near the park brake pedal. A fuse puller is attached to the inside surface of the fuse panel cover to aid in removing fuses, if necessary .
The coin slots are located under the instr ument panel center stack. Cup Holders The Durango has 8 cupholders. Four are located in the center console, two are located in the second r ow armrest, and two are located in the left hand quarter panel for third r ow occupants.
F ACTOR Y INST ALLED ROOF LUGGAGE RACK The load carried on the roof when equipped with a luggage rack must not exceed 68 kg (150 lbs.), and should be uniformly distributed over the cargo ar ea. The side rails between the stantions should be used to tie down cargo.
CAUTION! T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity . Always distribute heavy loads as evenly as possible and secure the load appropriately . Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
CARGO MANAGEMENT SYSTEM—IF EQUIPPED The cargo management system consists of a r emovable cargo liner and r emovable cargo or ganizer . T o open the side cover , pull on the cover latch.
INSTRUMENT P ANEL AND CONTROLS CONTENTS 䡵 Instruments And Contr ols ................. 1 8 1 䡵 Instrument Cluster ...................... 1 8 2 䡵 Instrument Cluster Description ............. 1 8 3 䡵 Radio Reception Information ............... 1 9 1 ▫ AM Reception .
䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio W ith Optional Satellite Radio, Hands Free Phone, And V ehicle Entertainment Systems (VES) Capabilities ........................... 2 0 0 ▫ Operating Instructions - Radio Mode ....... 2 0 1 ▫ Operation Instructions - (CD Mode For CD Audio Play) .
▫ PTY Button ⬙ Scan ⬙ ..................... 2 1 8 ▫ PTY Button ⬙ Seek ⬙ ..................... 2 1 9 ▫ Satellite Antenna ...................... 2 1 9 ▫ Reception Quality ..................... 2 1 9 䡵 Remote Sound System Controls — If Equipped .
䡵 Rear W indow Features ................... 2 3 7 ▫ Rear W indow W iper/W asher ............. 2 3 7 ▫ Rear W indow Defrosting ................ 2 3 8 180 INSTRUMENT P ANEL AND CONTROLS.
INSTRUMENTS AND CONTROLS INSTRUMENT P ANEL AND CONTROLS 181 4.
Instrument Cluster 182 INSTRUMENT P ANEL AND CONTROLS.
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. T emperature Gage The temperature gage indicates engine coolant temperature. Any r eading within the normal range indicates that the cooling system is operat- ing satisfactorily .
left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for mor e than one mile. 4. Low Fuel W arning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. 5. High Beam Indicator Indicates that headlights are on high beam.
CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately , and call for service.
13. ABS W arning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for approximately 3 seconds.
range (PRND21). If the PRNDL displays only the char- acters PRND21 (no boxes) have the system checked by an authorized dealer . 17. T rip Odometer The trip odometer shows individual trip mileage. T o toggle between the odometer and the trip odometer , press the Odometer/T rip Odometer Button.
⬙ ESP/TCS Indicator Light ⬙ also flashes when TCS is active. If the ⬙ ESP/TCS Indicator Light ⬙ begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sur e to adapt your speed and driving to the prevailing r oad conditions.
NOTE: A chime will sound if the vehicle is rolling and a door has been opened. 23. BRAKE System W arning Light The red “BRAKE” warning light will come on when the ignition key is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repair ed promptly .
driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. NOTE: • ⬙ The ⬙ ESP/TCS Indicator Light ⬙ and the ⬙ ESP/ BAS W arning Lamp ⬙ come on momentarily each time the ignition switch is turned ON.
27. Airbag Indicator The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned ON. If the light does not come on when the ignition is first turned on, or the light stays on or comes on while driving, have the airbag system checked by an authorized dealer .
another . Noise from storms and power lines can also interfere with AM reception. Reducing the tr eble can reduce some of the noise. FM Reception FM Stereo signals pr oduce better sound quality than AM signals. However , FM signals will only travel approxi- mately 10 to 40 miles (16 to 64 km).
SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Mode Button (Radio Mode) Press the mode button r epeatedly to select between the CD player or Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une/ Audio control. 3. After the hours are adjusted, press the right side T une/Audio control to set the minutes. The minutes will begin to blink.
Press the r otary TUNE control a fourth time and BAL will be displayed. T urn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the r otary TUNE control a fifth time and F ADE will be displayed.
Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display .
SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , cassette player or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
R W/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button r epeatedly to select between the CD player or Satellite Radio (if equipped). Operating Instructions - Hands Free Phone — If Equipped Refer to the HANDS FREE PHONE (UConnect™) section of the Owner’s Manual.
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
will return. Rotating the volume contr ol, turning the radio ON/OFF , or turning OFF the ignition will also return the sound fr om the speakers NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone.
R W/FF (Radio Mode) Pressing the r ewind/fast forward button causes the tuner to search for the next fr equency in the direction of the arrows. This featur e operates in either AM, FM or Satel- lite (if equipped) frequencies.
turning the TUNE rotary knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently br oadcast PTY information.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), .
SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the curr ent selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
• Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are supported by the radio.
MPEG Specifi- cation Sampling Fre- quency (kHz) Bit rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.
Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if avail- able). Press the MSG or INFO button once mor e to return to ⬙ elapsed time ⬙ priority mode.
Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability . Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
System Activation NOTE: Y our vehicle’s radio must be on and in satellite mode when the activation process takes place. T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.
ESN/SID Access W ith RAQ and RAK Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds.
Selecting a Channel Press and r elease the SEEK or TUNE knob to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
one and stop the search. Pr essing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button within five seconds.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a push button in the center .
The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pr e-set push-buttons.
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e. scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have theft protection encoding. T ry a known good disc before considering disc player service.
Air Conditioning Operation T o turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desir ed airflow setting. • Set the front blower contr ol to any desired speed. • Press the Snowflake (A/C) button which is located to the right of the temperature contr ol slide.
Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots and give an even blend of both modes.
NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives impr oved comfort during sunny but cool conditions. Heat (Floor) Outside air flows primarily through the floor out- lets located under the instrument panel.
T emperature Control The temperature of the air is contr olled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature. The blue ar ea of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures.
mode on the front contr ol will give you air from the outlets in the headliner in the rear . Floor mode in the front will give you floor in the r ear . Rear Window Defrosting and Rear Window W asher/Wiper See the “Rear W indow Features” section of this book.
The A TC system uses an infrared sensor located in the overhead console to measur e the temperature of the driver . Based on the sensor input, the system will auto- matically control comfort by varying the temperatur e, fan speed, and mode. This maintains a comfortable tempera- ture, even under changing conditions.
Manual Control (A TC) Y ou also may choose to customize your comfort by selecting the fan speed and mode manually . Pressing the fan speed button or any mode button places the system into manual operation. While in manual operation there ar e six fan speeds available and the choice of any mode.
Manual control of Recir culation is possible only in Panel, Floor , and Bi-Level modes. It will not operate in Mix, or Defrost modes. The r ecirculation symbol will flash thr ee times indicating recir culation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the recir culate button to return to outside air .
the A/C snowflake button has not been pressed. This dehumidifies the air to help dry the windshield. Rear T emperature Control (A TC) The “REAR” button cycles through the following modes: Rear Con.
Rear Zone Climate Control — If Equipped Headliner air comes from the outlets in the headliner . Each of these outlets can be individually adjusted to direct the flow of air . Moving the air vane knobs on the outlets to one side will shut off the airflow .
Rear Rotary Blower Control The second row seat occupants have contr ol of the rear blower speed, only when the front contr ol unit is in the “REAR CONTROL” position or CONTROL IN REAR ⬙ for A TC. ⬙ The rear blower switch has an “Of f” position and a range of blower speeds.
Front Unit to Rear Unit Chart If the Front Control is selected Rear Airflow will come from Panel Headliner Bi-Level Headliner • Between Bi-Level Floor Bi-Level Floor Floor Mix Floor Defrost Floor Op.
and blower speed to maintain comfort. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigar ette smoke, perfumes, etc.
Operating Tips Chart 236 INSTRUMENT P ANEL AND CONTROLS.
REAR WINDOW FEA TURES Rear Window Wiper/W asher A rotating switch located on the climate control panel turns the rear wiper On or Of f. Pressing the rotating switch inwar d activates the rear window washer . Rotating the switch will enable one of five intermittent delay times for the rear wiper .
If the rear wiper is operating when the ignition is turned off, the wiper will automatically r eturn to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 4 2 ▫ Automatic T ransmission ................ 2 4 2 ▫ Normal Starting ...................... 2 4 2 ▫ Engine Block Heater — If Equipped ........ 2 4 4 䡵 Automatic T ransmission .
䡵 T ire Safety Information ................... 2 6 4 ▫ T ire Markings ........................ 2 6 4 ▫ T ire Identification Number (TIN) .......... 2 6 8 ▫ T ire Loading And T ire Pressur e ........... 2 6 9 䡵 T ires—General Information ..
▫ Fuel System Cautions .................. 2 8 9 ▫ Carbon Monoxide W arnings .............. 2 9 0 䡵 Catalytic Converter ..................... 2 9 1 䡵 V ehicle Loading ........................ 2 9 2 ▫ Certification Label ..................... 2 9 2 ▫ Curb W eight .
ST ARTING PROCEDURES Automatic T ransmission Start the engine with the selector lever in NEUTRAL or P ARK position. Apply the brake before shifting to any driving range. W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way .
If Engine Fails T o Start If the engine fails to start after you have followed the Normal Starting procedur e, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
CAUTION! Long periods of engine idling can cause excessive exhaust temperatures which can damage your ve- hicle. Do not leave your vehicle unattended with the engine running. W ARNING! Do not leave children or animals inside parked vehicles in hot weather .
AUTOMA TIC TRANSMISSION Automatic T ransmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. T o drive, move the selector lever from Park or Neutral to the desired drive position.
W ARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
it also when climbing long grades, and for engine brak- ing when descending moderately steep grades. T o pre- vent excessive engine speed do not exceed 45 miles per hour (72 km/h) in this range. “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill.
If the transmission temperature gets extr emely hot, the transmission will automatically select the most desirable gear for operation at this temperature. If the transmission temperature becomes hot enough the TRANS TEMP light may illuminate and the transmission may downshift out of Overdrive until the transmission cools down.
equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) ar e allowed during steady cruise (for impr oved fuel economy) and automatic closed-throttle downshifts to 3r d gear (for improved braking) will occur during steady braking.
cause damage to the transmission. The torque converter will refill within five seconds of shifting fr om Park into any other gear position. FOUR-WHEEL DRIVE OPERA TION NV 144 T ransfer Case Operating .
W ARNING! Always engage the parking brake when powering down the vehicle if the ⴖ Service 4WD ⴖ light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury . NOTE: Do not attempt to make a shift while only the front or r ear wheels are spinning.
Shifting Procedure - NV 144 T ransfer Case A WD to 4LOCK or 4LOCK to A WD W ith the key ON and the engine either OFF or RUN- NING, rotate the transfer case switch, located on the instrument panel to the desir ed position.
If the key is not ON then the shift will not take place and no position indicator lights will be on or flashing. NV 244 Generation II T ransfer Case Operating Information / Precautions The NV 244 Generation II is an electric shift transfer case and is operated by the 4WD Control Switch, which is located on the instrument panel.
NOTE: The transfer case Neutral (N) position is to be used for recr eational towing only . See Recreational T ow- ing section for specific procedur es on shifting into and out of Neutral (N). T ransfer Case Position Indicator Lights T ransfer case position indicator lights are located on the instrument cluster .
When operating your vehicle in 4LO, the engine speed is approximately thr ee times that of the A WD or 4LOCK positions at a given road speed. T ake care not to over- speed the engine and do not exceed 40 km/h (25 mph). Proper operation of four -wheel-drive vehicles depends on tires of equal size, type and cir cumference on each wheel.
4LOCK Four-Wheel-Drive LOCK - Locks the transfer case inter - axle differ ential. Forces fr ont and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only . 4LO Four-Wheel-Drive Low Range - Low speed 4 wheel drive.
wheels to complete the shift. There may be a delay up to 13 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4LOCK position may be experienced due to uneven tire wear , low tire pr essure, or excessive loading.
NOTE: If any of the requir ements to select a new transfer case position have not been met, the transfer case will not shift. The indicator light will flash and the current transfer case position will be maintained. T o retry the selection, turn the control knob back to the curr ent position, wait five (5) seconds, and retry the shift.
NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. Y ou must be sure the parking brake is fully applied befor e leaving the vehicle. When parking on a hill, turn the front wheels towar d the curb on a downhill grade and away from the curb on an uphill grade.
BRAKE SYSTEM In the event power assist is lost for any reason, (for example, repeated brake applications with the engine off), the brakes will still function. The ef fort requir ed to brake the vehicle will be significantly increased over that requir ed with the power system operating.
At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode.
W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
If for some reason, the power assist is interr upted, it will still be possible to steer your vehicle. Under these condi- tions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
ROCKING THE VEHICLE If vehicle becomes stuck in snow , sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressur e to the accelerator .
• European Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tir e size designation. Example: 215/65R15 96H • L T (Light T ruck)-Metric tire sizing is based on U.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle.
272 ST ARTING AND OPERA TING.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure”.
loading may be requir ed for high speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pr essures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity .
Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tir e warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the fr ont or rear axle of your vehicle, but it is not.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear .
These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es of Durango trucks. NOTE: The use of class “S” chains is permitted on Durangos with P245/70R17 tires.
TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns.
FUEL REQUIREMENTS All engines (except 5.7L engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality un- leaded “regular” gasoline having an oc- tane rating of 87. The routine use of pr e- mium gasoline is not recommended.
and durability for your vehicle. W e recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country r equire the use of cleaner burning gasoline referr ed to as “Reformulated Gasoline.
MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT . Gasolines blended with MMT reduce spark plug life and reduce emission system performance.
NOTE: T ighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. Make sure that the gas cap is tightened each time the vehicle is refueled. W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. W ARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases.
CA T AL YTIC CONVERTER The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not requir e maintenance.
vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained imme- diately . T o minimize the possibility of catalyst damage: • Do not shut off the engine or interr upt the ignition when the transmission is in gear and the vehicle is in motion.
Rating (GA WR) front and r ear , and V ehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day , and Hour of manufacture. The bar code that appears on the bottom of the label is your V ehicle Identification Number (VIN).
Inflation Pressure (Cold) This is the cold tire inflation pr essure for your vehicle for all loading conditions up to full GA WR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
W ARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle.
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible.
Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and r ear axles. Distribute the load over the front and r ear axles evenly . Make sure that you do not exceed either front or rear GA WR. W ARNING! It is important that you do not exceed the maximum front or rear GA WR.
W eight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame.
T railer Hitch Classification Class Max. GTW (Gross T railer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1587 kg) Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV.
Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle.
CAUTION! • A void towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual.
• Safety chains must always be used between your vehicle and trailer . Always connect the chains to the frame or hook retainers of the vehicle hitch. Cr oss the chains under the trailer tongue and allow enough slack for turning corners. • V ehicles with trailers should not be parked on a grade.
− Check for signs of tire wear or visible tir e damage before towing a trailer . Refer to the T ires–General Information section of this manual on T read W ear Indicators for the proper inspection pr ocedure.
W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. Y ou might not have brakes when you need them and could have an accident. T owing any trailer will increase your stopping dis- tance.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
NOTE: Check the automatic transmission fluid level before towing. T owing T ips — T ow/Haul (If Equipped) T o reduce potential for automatic transmission over heat- ing, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more sever e grades.
T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped Out or In).
W ARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational T owing 2WD Models Recreational towing of 2WD models is not allowable.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
2. Shut engine OFF . 3. T urn the ignition key to the ON position without starting the engine. 4. Depress brake pedal. 5. Shift automatic transmission to Neutral (N). 6. Using the point of a ballpoint pen or similar object, depress the r ecessed transfer case Neutral (N) button for 4 seconds.
NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing.
NOTE: Items 1 through 5 ar e requir ements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until 1 second elapses and the shift has been completed.
2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 3 1 6 䡵 Adding Fuel .......................... 3 1 6 䡵 Changing A Flat T ire .................... 3 1 7 ▫ Jack Location ........................ 3 1 7 ▫ Removing The Spare T ire .
HAZARD W ARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and r ear directional signals will flash intermittently . Press the switch a second time to turn of f the emergency flashers.
W ARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
W ARNING! The jack is designed as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only .
Removing The Spare Tire The spare tir e on the Dodge Durango is located under- neath the vehicle in the rear . Remove the spare tir e before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area. 2. Engage the jack wrench extension to the spar e tire winch through the hole in the floor .
It is recommended that you stow the flat or spar e to avoid tangling the loose cable. CAUTION! The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch.
Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in P ARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position.
(prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube exten- sion, may be used but is not requir ed. When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
W ARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack, tools and the extra tire and wheel in the places provided. 7. Remove wheel blocks. Do not install chrome or alu- minum wheel center caps on the spare wheel.
T o Stow The Flat Or Spare T urn the wheel so that the valve stem is down. Slide the wheel retainer thr ough the center of the wheel and position it properly acr oss the wheel opening. For convenience in checking the spare tir e inflation, stow with the valve stem toward the r ear of the vehicle.
Check the Battery T est Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery .
W ARNING! Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
W ARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. W ARNING! Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road.
Four-Wheel Drive V ehicles The manufacturer r ecommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly .
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment 3.7L V6 .............. 3 3 4 䡵 Engine Compartment 4.7L V -8 .............. 3 3 5 䡵 Engine Compartment 5.7L HEMI V -8 ......... 3 3 6 䡵 Onboard Diagnostic System — OBD II ........ 3 3 7 ▫ Loose Fuel Filler Cap Message .
▫ Catalytic Converter .................... 3 4 7 ▫ Maintenance-Free Battery ................ 3 4 8 ▫ Air Conditioner Maintenance ............. 3 4 9 ▫ Power Steering — Fluid Check ............ 3 5 0 ▫ Front Suspension Ball Joints .........
䡵 Bulb Replacement ...................... 3 7 7 ▫ Headlights/Parking/T urn Signal .......... 3 7 7 ▫ Rear Side Marker , T ail Lights, T urn Signals And Backup Lights — Replacement ........ 3 7 8 ▫ License Lights ........................ 3 8 2 ▫ Center High-Mounted Stoplight .
ENGINE COMP ARTMENT 3.7L V6 334 MAINT AINING YOUR VEHICLE.
ENGINE COMP ARTMENT 4.7L V -8 MAINT AINING YOUR VEHICLE 335 7.
ENGINE COMP ARTMENT 5.7L HEMI V -8 336 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Pr ess the odometer reset button to turn the message of f. If the problem persists, the message will appear the next time the vehicle is started.
3. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 4. Approximately 15 seconds later , one of two things will happen: a. The MIL light will blink for appr oximately 5 sec- onds and then remain on until the first engine crank or the key is turned off.
DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pr ocedure yourself.
1. Position the vehicle on a level surface. 2. T urn Off the engine and allow appr oximately 5 min- utes for the oil to settle to the bottom of the crankcase. 3. Remove the engine oil level indicator (dipstick). 4. W ipe the engine oil level indicator (dipstick) clean.
Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures ar e below 32°F (0°C). • Stop and Go driving.
periodically . Make sure that these units are always clean. This will tend to reduce to a minimum the amount of abrasive material that may enter the engine.
For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used.
Drive Belts — Check Condition and T ensioner Belt tension is controlled by means of an automatic tensioner . No belt tension adjustments are r equired. However , belt and belt tensioner condition should be inspected at the specified intervals, and replaced if r e- quired.
Ignition Cables Replace the ignition cables (5.7L engines only) at the mileage interval shown in the maintenance charts. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”.
Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
W ARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery . T o determine the battery charge, check the battery test indicator (if equipped) on top of the battery . Refer to the illustration.
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the pr oper indicated level.
attention should also be given to hood latching compo- nents to insure pr oper function. When performing other underhood services, the hood latch, r elease mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year , preferably in the fall and spring.
W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
W ARNING! Y ou or others can be badly burned by hot coolant or steam from your radiator . If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool. If you open the hood and see steam or hot coolant escaping from the radiator , don’t touch anything.
Recommended Engine Coolant This vehicle has been factory filled with an Ethylene Glycol based engine coolant with long life corrosion inhibitors (called HOA T , for Hybrid Organic Additive T echnology). Follow the “Maintenance Schedule” for the recommended coolant change intervals.
Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOA T ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺ 34°F ( ⫺ 37°C) ar e anticipated.
W ARNING! The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. T o prevent scalding or injury , do not remove the pres- sure cap when the system is hot or under pressure.
D. Maintain coolant concentration at 50% HOA T ethyl- ene glycol engine coolant (minimum) and distilled water for proper corr osion protection of your engine. E. Make sure that the radiator and coolant bottle over- flow hoses are not kinked or obstr ucted.
Y ou are ur ged to use only the manufacturer’s specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing. It is manda- tory to replace all clamps that have been loosened or removed during service. Car e should be taken in install- ing new clamps to insure they ar e properly tor qued.
W ARNING! Use of brake fluid that may have a lower initial boiling point, or is unidentified, as to specifications may result in sudden brake failure during hard prolonged braking. Y ou could have an accident. W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching on fire.
W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately . Automatic T ransmission Fluid Level Check Check the fluid level while the transmission is at normal operating temperature 180°F (82°C).
a minimum of two (2) minutes for the oil to fully drain into the transmission before r echecking the fluid level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at approximately 70°F ( 21°C) (r oom temperature).
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Axles Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. The manufacturer does not r ecommend regularly sched- uled oil changes for axles in vehicles whose operation is classified as normal truck service. NOTE: The presence of water in the gear lubricant will result in corr osion and possible failure of dif ferential components.
There ar e two groups identified, those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Perfor- mance categories within these groups r esult in dual letter designations for each group.
The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar . • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. W ashing • W ash your vehicle regularly .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the r esponsibility of the owner . • If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating have your vehicle repair ed as soon as possible.
Y our leather upholstery can be best preserved by r egular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed pr omptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar 威 T otal Clean.
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
FUSE BLOCK CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow , it suggests a problem in the circuit that must be corrected.
Cavity Mini Fuse/Color Description F1 15 Amp Blue Instrument Cluster Battery Feed F 2 10 Amp Red Occupant Classification Module (OCM) Battery Feed F3 10 Amp Red Ignition Run/Start for Con- troller (NG.
Cavity Mini Fuse/Color Description F1 1 10 Amp Red Heated Mirrors F12 20 Amp Y ellow Cluster Battery Feed F13 10 Amp Red Ignition Run HV AC Module/Heated Rear Glass (EBL) Relay F14 10 Amp Red ABS Modu.
Cavity Cartridge Fuse / Relay Mini Fuse Description 12 40 Amp Green JB Feed / EBL /TC a s e Brake 13 30 Amp Pink JB Feed RR 14 40 Amp Green ABS Pump 15 50 Amp Red JB Feed 16 10 Amp Red Crank 17 Spare .
Underhood Fuses (Integrated Power Module) Cavity Cartridge Fuse / Relay Mini Fuse Description 1 Relay W iper On/Off Rly 2 Relay W iper Hi/Lo Rly 3 Relay Horn Rly 4 Relay Rear W iper Rly 5 Relay Lt T -.
Cavity Cartridge Fuse / Relay Mini Fuse Description 24 Relay Rad Fan Lo Rly 25 Relay Ft Fog Lamps Rly 26 Relay Adjustable Pedal Rly 27 30 Amp Green IOD #1 28 30 Amp Green IOD #2 29 Spare 30 Spare REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb No.
BULB REPLACEMENT Headlights/Parking/T urn Signal 1. Remove the two bolts attaching the headlight to the inner fender panel. 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner .
6. T wist and remove socket fr om lamp. 7. Remove bulb from socket and replace. NOTE: These are Halogen bulbs. T ake care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat build-up which reduces bulb life.
2. Rotate the light to the outboard side of the vehicle and remove. MAINT AINING YOUR VEHICLE 379 7.
3. Unlock and remove electrical connector . 4. Remove the three screws holding the bulb strip to the back of the tail lamp. 380 MAINT AINING YOUR VEHICLE.
5. Remove the bulb strip from the tail light lens. 6. Remove bulbs fr om bulb strip by pulling the bulb straight out. MAINT AINING YOUR VEHICLE 381 7.
License Lights 1. Remove the two screws securing the lens to the liftgate. 382 MAINT AINING YOUR VEHICLE.
2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket. Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assem- bly to the liftgate.
2. T urn socket 1/4 counterclockwise and fr ee from hous- ing. 3. Pull bulb straight from socket to remove. Fog Lights 1. Rotate bulb and connector 1/4 turn counterclockwise.
FLUIDS AND CAP ACITIES U.S. Metric Fuel 3.7L/4.7L, 87 Octane 27 Gal. 102L 5.7L, 89 Octane 27 Gal 102L Engine Oil (with filter) 3.7L, SAE 5W -30, API Certified 5 Qt. 4.7L 4.7L, SAE 5W -30, API Certified 6 Qt. 5.7L 5.7L, SAE 5W -20, API Certified 7 Qt. 6.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifr eeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. 3.7/4.7L Engine Oil Use SAE 5W -30, API Certified, meeting material standar d MS-6395 or equiva- lent.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar 威 A TF+4, Automatic T ransmission Fluid. T ransfer Case Mopar 威 A TF+4, Automatic T ransmission Fluid. Front Axle SAE 75W -90 Multipurpose T ype, GL-5 Gear Lubricant or equivalent.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 9 0 䡵 Emissions T esting ....................... 3 9 0 䡵 Maintenance Schedules ................... 3 9 1 ▫ Schedule “B” ........................ 3 9 4 ▫ Schedule “A” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued pr oper func- tioning of the emission control system.
MAINTENANCE SCHEDULES There ar e two maintenance schedules that show the required service for your vehicle. First is Schedule “B” . It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule.
Use the schedule that best describes your driving condi- tions. Where time and mileage ar e listed, follow the interval that occurs first. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , and transmission and add as needed.
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 33,000 36,000 39, 000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Inspect auto tension drive belt and replace if r e- quired. X Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your ve- hicle is used for police, taxi, fleet, or frequent trailer towing.
Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. XXX X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers ) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXX Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage.
Miles 93,000 96,000 99,000 102,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. XXX X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 105,000 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter , or at 3 months whichever comes first. X X XXXX Rotate tires. X X X Check spare tir e for proper pr essure and cor- rect stowage.
Miles 105,000 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Drain and refill transfer case fluid (4X4). X Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your vehicle is used for police, taxi, fleet, or fre- quent trailer towing.
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stowage.
Miles 36,000 42,000 48,000 54,000 60,000 66,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [36] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X X X X X Rotate tir es. X X X X X X Check spare tir e for proper pr essure and cor- rect stowage.
Miles 36,000 42,000 48,000 54,000 60,000 66,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [36] [42] [48] [54] [60] [66] Inspect engine air cleaner filter , replace if necessary . X Replace spark plugs. X Inspect PCV valve, replace as necessary .
Miles 72,000 78,000 84,000 90,000 96,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) [Months] [72] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stowage.
Miles 102,000 108,000 1 14,000 120,000 (Kilometers) (170 000) (180 000) (190 000) (200 000) [Months] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X X Rotate tir es. X X X X Check spare tir e for proper pr essure and correct stowage.
Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 1 2 ▫ Prepar e For The Appointment ............ 4 1 2 ▫ Prepar e A List ........................ 4 1 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
.
INDEX 10.
ABS (Anti-Lock Brake System) ............ 186,260 Adding Fuel ........................ 287,316 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 346 Air Conditioner Maintenance ............ 223,349 Air Conditioning ........................ 2 2 2 Air Conditioning, Operating T ips .
Ball Joints ............................. 3 5 1 Battery ............................... 3 4 8 Charging ............................ 3 2 5 Emergency Starting ..................... 3 2 5 Gas Caution .......................... 3 2 5 Keyless T ransmitter Replacement (RKE) .
Cargo Or ganizer ....................... 1 7 6 Cargo Or ganizer ........................ 1 7 6 Cargo (V ehicle Loading) ................... 2 9 2 Catalytic Converter .................... 291,347 CD (Compact Disc) Player ............... 193,200 Cellular Phone .
Points to Remember .................... 3 5 8 Radiator Cap ......................... 3 5 7 Selection of Coolant (Antifreeze) ...... 356,385,386 T emperature Gauge ..................... 1 8 3 Cruise Contr ol (Speed Control) .............. 1 4 2 Cup Holder .
Jacking ............................. 3 2 0 Overheating .......................... 3 5 7 T ow Hooks .......................... 3 2 7 T owing ............................. 3 2 8 Emission Control System Maintenance ......... 3 9 0 Emission Related Components .
Engine Oil Disposal .................... 3 4 4 Flashers Hazard W arning ....................... 3 1 6 T urn Signal ..................... 136,183,378 Flat T ire Stowage ..................... 319,325 Flooded Engine Starting ................... 2 4 3 Floor Console .
Gasoline, Reformulated ................... 2 8 6 Gauges Coolant T emperature .................... 1 8 3 Fuel ................................ 1 8 3 Odometer ........................... 1 8 7 Speedometer ......................... 1 8 5 T achometer ....
Lock ................................ 1 3 Illuminated Entry ........................ 1 4 Infant Restraint ........................ 64,65 Inflation Pressur e T ires .................... 2 8 2 Inside Rearview Mirror .................... 8 4 Instrument Cluster .
Bulb Replacement ................... 376,377 Center Mounted Stop ................... 3 8 3 Courtesy/Reading ..................... 1 5 5 Cruise .............................. 1 9 1 Daytime Running ...................... 1 3 4 Door Ajar ................
Lower Anchors and T ether for CHildren (LA TCH) .............................. 6 7 Lubricating Oil ......................... 3 6 5 Lubrication, Body ....................... 3 5 1 Lug Nuts ............................. 3 2 3 Luggage Carrier ...........
Change Interval ....................... 3 4 2 Dipstick ............................. 3 4 0 Disposal ............................ 3 4 4 Filter ............................ 344,386 Filter Disposal ........................ 3 4 4 Identification Logo .....
Sunroof ............................. 1 6 8 W indows ............................. 3 4 Power Steering Fluid ..................... 3 8 7 Pregnant W omen and Seat Belts .............. 4 7 Preparation for Jacking .................... 3 2 1 Pretensioners Seat Belts .
Replacement Parts ....................... 3 3 9 Replacement T ires ....................... 2 8 0 Reporting Safety Defects ................... 4 1 5 Restraints, Child ....................... 64,69 Restraints, Occupant ...................... 3 6 Rocking V ehicle When Stuck .
Sentry Key Programming ................... 1 2 Service and Maintenance ............. 340,390,391 Service Assistance ....................... 4 1 2 Service Contract ......................... 4 1 4 Service Manuals ........................ 4 1 6 Setting the Clock .
Stuck, Freeing .......................... 2 6 4 Sun Roof .............................. 1 6 8 Supplemental T ire Pressur e Information ........ 2 8 2 Synthetic Engine Oil ...................... 3 4 4 System, Remote Starting .................... 2 8 T achometer .
Spare T ire ........................... 3 1 9 Spinning ............................ 2 7 8 T read W ear Indicators ................... 2 7 9 Wheel Mounting ....................... 3 2 0 Wheel Nut T orque ..................... 3 2 3 T ongue W eight/T railer W eight .
T ransmitter Programming (Remote Keyless Entry) .................... 2 4 T read W ear Indicators .................... 2 7 9 T rip Computer .......................... 1 5 6 T rip Odometer .......................... 1 8 7 T rip Odometer Reset Button ...
W indshield W iper Blades .................. 3 5 2 W indshield W ipers ....................... 1 3 7 W iper Blade Replacement .................. 3 5 2 W iper , Rear ............................ 2 3 7 W ipers, Intermittent ...................... 1 3 7 W recker T owing .
NOTES.
NOTES.
NOTES.
An important point after buying a device Dodge 2006 Durango (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dodge 2006 Durango yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dodge 2006 Durango - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dodge 2006 Durango you will learn all the available features of the product, as well as information on its operation. The information that you get Dodge 2006 Durango will certainly help you make a decision on the purchase.
If you already are a holder of Dodge 2006 Durango, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dodge 2006 Durango.
However, one of the most important roles played by the user manual is to help in solving problems with Dodge 2006 Durango. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dodge 2006 Durango along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
