Instruction/ maintenance manual of the product 2004 Neon SRT4 Dodge
Go to page of 200
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS m Introduction ........................... 4 m How T o Use This Manual ................. 4 m W arnings And Cautions .................. 6 m V ehicle Identification Number .............. 6 m V ehicle Modifications / Alterations ...
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys ................. 9 ▫ Locking Doors W ith The Key .............. 9 ▫ Key-In-Ignition Reminder ................ 9 m Sentry Key ............................ 9 ▫ Replacement Keys .
▫ T o Unlock The T runk .................... 1 7 ▫ Using The Panic Alarm .................. 1 7 ▫ Programming Additional T ransmitters ........ 1 7 ▫ General Information .................... 1 8 ▫ T ransmitter Battery Service ...............
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer . Ask your dealer for these numbers and keep them in a safe place. The double sided keys may be inserted into the locks with either side up.
immediately after the ignition switch is turned on for a bulb check. Afterwar ds, if the bulb remains on, this indicates a problem with the electr onics. If the bulb begins to flash after the bulb check, this indicates that an invalid key has been used to start the vehicle.
consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer .
STEERING WHEEL LOCK Y our vehicle is equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key . If the steering wheel is rotated no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Child-Protection Door Lock System (Rear Doors) T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
INTERNAL EMERGENCY TRUNK LID RELEASE W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
REMOTE KEYLESS ENTR Y This system allows you to lock or unlock the doors and trunk or activate the panic alarm fr om distances up to about 23 feet (7 meters) using a hand held transmitter . NOTE: A slight delay of up to two seconds can occur before the doors or tr unk will unlock.
T o Unlock the T runk Press the TRUNK button on the transmitter twice to unlock the trunk. NOTE: A slight delay of up to two seconds can occur before the tr unk unlatches. Using The Panic Alarm T o turn on the panic alarm feature, pr ess and release the P ANIC button.
General Information This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be r eceived, in- cluding interference that may cause undesir ed operation.
POWER WINDOWS The window switches on the driver’s door panel control both front windows. The switch on the passenger’s door panel controls the passenger’s window . OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems.
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. • W earing your belt in the wrong place could make your injuries in a collision much worse.
2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
2. At about 6 to 12 inches above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if ther e is a collision. Seat Belt Extender If a seat belt is too short, even .
If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deploy- ment.
Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instr u- ment panel knee bolsters to provide impr oved protection for the driver and front passenger . Side airbags also work with seat belts to improve occupant pr otection.
If a child from 1 to 12 years old must ride in the fr ont passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. See the section on Child Restraint. Y ou should read the instructions pr ovided with your child restraint to make sur e that you are using it properly .
Airbag System Components The front airbag system consists of the following: • Airbag Control Module (ACM) • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Col.
• The Airbag Control Module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned to ON/RUN, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momen- tarily or continuously .
• The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag. If A Deployment Occurs The airbag system is designed to deploy when the Airbag Control Module detects a moderate-to-sever e frontal collision, to help restrain the driver and fr ont passenger , and then to immediately deflate.
W ARNING! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Side Airbag System — If Equipped • The Side Impact Airbag Control Modules determine if a side collision is severe enough to r equire the airbag to inflate.
Maintaining Y our Airbag Systems W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you.
Children 12 years and under should ride pr operly buck- led up in a rear seat, if available. According to crash statistics, children ar e safer when properly restrained in the rear seats, rather than in the fr ont. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle.
• Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forwar d-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing dir ection are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year .
• The restraint must be appr opriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instr uctions that come with the restraint. If you install the r estraint improperly , it may not work when you need it.
the rear seat to install the child r estraint. Y ou will easily feel them if you run your finger along the intersection of the surfaces. The lower strap hooks are passed over the top of each bar , pushing aside the seat cover material.
3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child r estraint manufacturer’s instruc- tions. W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
W ARNING! Do not install child restraint systems equipped with LA TCH attachments at all three rear seating posi- tions at one time. The LA TCH anchorages are de- signed to restrain no more than two child restraints at a time in the event of a collision.
• The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and not an indication of a pr oblem. SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless.
Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the bulb is not lit during starting, have it replaced. If the light stays on or comes on while driving, have the system checked by an authorized dealer .
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors .............................. 4 7 ▫ Inside Day/Night Mirror ................. 4 7 ▫ Outside Mirror — Driver’s Side ............ 4 7 ▫ Outside Mirror — Passenger’s Side ....
▫ W indshield W ashers .................... 5 5 ▫ Mist Function ......................... 5 6 ▫ Intermittent W iper System ................ 5 6 ▫ Lo Speed W ipers ....................... 5 6 ▫ Hi Speed W ipers ....................... 5 6 m T ilt Steering Column .
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
Electric Remote-Control Mirrors Use the mirror select switch, located on the drivers door trim panel, to adjust the view obtained in the outside mirrors. Pr ess the rocker knob to the L or R for Left or Right mirror selection. Use the center of f position to guard against accidentally moving a mirr or position.
W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Folding Rear Seat T o provide additional storage ar ea, the center of each rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the driver’s side of the instrument panel. Then lift the safety catch located under the front edge of the hood, near the center and raise the hood.
Use the hood prop r od to secure the hood in the open position as shown. T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. W ARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision.
Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. T urn the ignition switch ON to restor e the interior light operation.
lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights T urn the end of the Multi-Function Control Lever to the first detent for parking light operation.
T urn Signals Move the Multi-Function Control Lever up or down to detent and the arrows on each side of the instr ument cluster flash to show proper operation of the fr ont and rear turn signal lights. Y ou can signal a lane change by moving the lever partially up or down.
If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF . CAUTION! • In cold weather , always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.
TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towar ds you to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
CONSOLE FEA TURES The Standard console with armr est has two front cup holders and a front storage tray . There ar e two additional cupholders; one is molded in the center of the console to hold large cups, and the other is on the underside of the console lid to serve passengers in the rear seat.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instrument Panel Featur es ................ 6 1 m Instrument Cluster—T urbo ................ 6 2 m Instrument Cluster Descriptions ............ 6 3 m Electronic Digital Clock .................. 6 8 ▫ Clock Setting Procedur e.
▫ Selecting Satellite Mode In RBP , RBU, RAZ, And RBQ Radios ...................... 7 5 ▫ Selecting a Channel ..................... 7 5 ▫ Storing And Selecting Pre-Set Channels ....... 7 6 ▫ Using The PTY (Pr ogram T ype) Button (If Equipped) .
INSTRUMENT P ANEL FEA TURES UNDERST ANDING YOUR INSTRUMENT P ANEL 61 4.
INSTRUMENT CLUSTER—TURBO 62 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fog Light Indicator This light shows when the fog lights are ON. 2. Brake System W arning Light This light monitors various brake functions, including brake fluid level and parking brake application.
If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed, however , the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on.
The light does not show the quantity of oil in the engine. This can be determined using the procedur e shown in Section 7. 9. Seat Belt Reminder Light When the ignition key is first turned on, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor .
16. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine con- trol systems. The light will illuminate briefly when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly .
20. T rip Indicator This light will illuminate when the T rip Odometer is in use. 21. T emperature Gauge The temperature gauge shows engine coolant temperature. Normal operating range should be within one notch above or one notch below the 200 degree mark.
ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the fr equency variations that carry the FM signal.
Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it.
Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory .
display will show the track number and index time in minutes and seconds. Play will begin at the start of track 1. Seek Press the top of the SEEK button for the next selection on the CD.
CD Changer Operation — If Equipped MODE Press the MODE button to select between the cassette tape player , CD player , and the CD changer (if equipped).
SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to r eceiver broadcast- ing technology to provide clear digital sound, coast to coast.
ESN/SID Access W ith RBP , RBU, RAZ, and RBQ Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds.
888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory .
• Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. COMP ACT DISC MAINTENANCE T o keep the compact discs in good condition, take the following precautions: 1.
CLIMA TE CONTROLS Air Conditioning The Air Conditioning System allows you to balance the temperature, amount, and dir ection of air circulating throughout the vehicle. The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere.
Bi-Level Air is directed thr ough the panel and floor out- lets. NOTE: There is a dif ference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives impr oved comfort during sunny but cool conditions.
NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con- denser located in front of the radiator , for an accumula- tion of dirt or insects. Clean with a gentle water spray from behind the radiator and thr ough the condenser .
Operating Tips UNDERST ANDING YOUR INSTRUMENT P ANEL 81 4.
W indow Fogging V ehicle side windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C, P ANEL and blower controls. Direct the panel outlets toward the side windows. Do not use r ecirculate without A/C for long periods as fogging may occur .
ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrument panel, below the radio, turns the defroster ON or OFF . An amber light shows that the defroster is on. NOTE: The defroster turns of f automatically after 10 minutes of operation.
.
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es ..................... 8 7 ▫ Manual T ransaxle ...................... 8 7 ▫ Normal Starting ....................... 8 7 ▫ Starting In Cold W eather (Below 32°F Or 0°C) ...................
▫ T ire Inflation Pressur es ................. 1 0 5 ▫ Radial-Ply T ires ...................... 1 0 7 ▫ Compact Spare T ire .................... 1 0 7 ▫ T ire Spinning ........................ 1 0 8 ▫ T read W ear Indicators ................
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
If the engine fails to start within 15 seconds, turn the key OFF wait 10 to 15 seconds, then repeat the normal starting procedur e. W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
CAUTION! T o prevent damage to the starter , do not crank the engine for more than 15 seconds at a time. W ait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up.
MANUAL TRANSAXLE NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving the vehicle, especially on an incline. NOTE: Clutch must be depressed for engine to start. Fully depress the clutch pedal befor e you shift gears.
Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch.
If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer . The engine will run normally when you reduce engine speed. Downshifting Proper downshifting may impr ove fuel economy and prolong engine life.
When parking on a hill,, turn the front wheels towar d the curb on a downhill grade and away from the curb on a uphill grade. Y ou should always apply the parking brake before leav- ing the vehicle. W ARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons.
BRAKE SYSTEM Y our vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, r epeated brake applications with the engine off), the brakes will still function. The effort r equired to brake the vehicle will be much greater than that requir ed with the power system operating.
W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards L T = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
ST ARTING AND OPERA TING 103 5.
W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tire rolling r esistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pr essure”.
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h).
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm).
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Tire Chains Due to limited clearance, tire chains ar e not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. Snow Tires Some areas of the country r equire the use of snow tires during winter .
Snow tires may have a lower speed rating than factory equipped tires and may not match the maximum vehicle speed. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).
The requir ed rotation method for directional tir es is to swap the front tir e with the rear on the same side of the vehicle. Do not cross switch tir es without dismounting the tires and r e-mounting them in the correct rotational direction. SELECTING FUEL 2.
Reformulated Gasoline Many areas of the country r equire the use of cleaner burning fuel referr ed to as Reformulated Gasoline. Re- formulated gasolines contain oxygenates, and are specifi- cally blended to reduce vehicle emissions and impr ove air quality .
vehicle. The MMT content of gasoline may not be indi- cated on the gasoline pump, therefor e you should ask your gasoline retailer whether or not his/her gasoline contains MMT . It is even more important to look for gasolines without MMT in Canada because MMT can be used at higher levels than allowed in the United States.
ADDING FUEL NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured fr om a portable container , the container should have a flexible nozzle long enough to force open the restricting door .
W ARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury . • The volatility of some gasolines may cause a build up of pressure in the fuel tank that may increase while you drive.
.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher ................. 1 2 0 m If Y our Engine Overheats ................ 1 2 0 m Jacking And T ire Changing ............... 1 2 2 ▫ Preparations For Jacking ................ 1 2 2 ▫ Instructions .
HAZARD W ARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and r ear direc- tional signals will flash. Depress the switch again to turn Hazard W arning Flashers off.
the fan control to High. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads over 250 degrees (in the red zone), pull over and stop the vehicle.
JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. CAUTION! Do not attempt to raise the vehicle by jacking on the crossmember below the radiator or on the front suspension crossmember .
Do not raise the vehicle until you are sur e the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire clears the surface. Miminum tire lift pr ovides maximum vehicle stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
7. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut tor que is 100 ft. lbs. (135 N·m.). If you are not sur e about the tightness, have them checked with a torgue wr ench by your dealer or at a service station.
1. W ear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water .
W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow , it can often be moved by a rocking motion.
TOWING A DISABLED VEHICLE With Ignition Key Y our vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels of f the ground.
MAINT AINING YOUR VEHICLE CONTENTS m 2.4L T urbo Charged Engine Compartment .... 1 3 3 m Onboard Diagnostic System — OBD II ...... 1 3 4 m Emissions Inspection And Maintenance Programs ............................ 1 3 4 m Replacement Parts .........
▫ Hoses And V acuum/V apor Harnesses ....... 1 5 2 ▫ Brake System ........................ 1 5 3 ▫ Manual T ransaxle ..................... 1 5 5 ▫ Appearance Care And Protection From Corrosion ........................... 1 5 5 m Fuses ........
2.4L TURBO CHARGED ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 133 7.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, and engine control systems.
Normally , the OBD system will be ready . The OBD system may not be ready if your vehicle was r ecently serviced, if you recently had a dead battery , or a battery replacement. If the OBD system should be determined not ready for the I/M test, your vehicle may fail the test.
vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT P ARTS Use of genuine Mopar parts for normal/scheduled main- tenance and repairs is highly r ecommended to insure the designed performance.
Engine Oil Checking Oil Level T o assure pr oper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you.
the requir ements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395. The manufacturer recommends the use of Mobil 1 t 10W30 synthetic engine oil.
the engine oil. Engine oil is an engineered pr oduct and it’s performance may be impaired by supplemental ad- ditives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil fr om your vehicle. Used oil, indiscriminately discarded, can present a pr oblem to the environment.
Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
Engine T iming Belt Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition Wiring System The ignition cables should be kept clean and properly connected. T erminals should be fully seated. Cracked, damaged, or faulty cables should be replaced.
CAUTION! When servicing the battery , always reinstall the battery thermowrap. The thermowrap provides bat- tery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not requir ed. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner , or use the washer solvent. This will remove accumulations of salt or r oad film and help reduce str eaking and smearing.
Windshield W asher Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition key to the OFF position. The fan is temperature con- trolled and can start at any time the ignition key is in the ON position.
Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring pr oper disposal. Check with your local authorities to determine the disposal rules for your community . Do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground.
Adding Coolant When adding coolant, a minimum solution of 50% eth- ylene glycol antifreeze coolant in water should be used. Use higher concentrations (not to exceed 70%) if tempera- tures below –34°F (-37°C) ar e anticipated. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution.
The radiator normally remains completely full, so ther e is no need to remove the radiator cap unless checking for coolant freeze point or r eplacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory , the coolant bottle need only be checked once a month.
E. Make sure that the radiator and coolant bottle hoses are not kinked or obstr ucted. F . Keep the front of the radiator and air conditioning condenser clean. G. Do not change the thermostat for summer or winter operation. If replacement is ever necessary , install ONL Y the correct type thermostat.
Brake System In order to assur e brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Section. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter .
hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under - body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corr osion resistance built into your vehicle.
Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the under carriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and r ear deck lid be kept clear and open.
DO NOT USE: • Any abrasive cleaner • Any abrasive cleaning pad (such as steel wool) or abrasive brush • Any cleaner that contains an acid which can react with and discolor the chrome surface. CAUTION! Many wheel cleaners contain acids that may harm the wheel surface.
W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights.
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts fr om the vehicle to wash them.
Interior Fuses The fuse access panel is behind the end cover at the left side of the instrument panel. T o remove the panel, pull it out, as shown. A diagram identifying the components and circuits is located on the inside of the cover . CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. ABS Indicator .......................... L E D Airbag Indicator ........................ L E D Brake System W arning Indicator ............. L E D Climate Controls ........................ L E D Console Gear Selector .
BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the three upper fascia screws. 2. Remove two screws from the headlight assembly and remove the assembly fr om the vehicle.
Front Park/T urn Signal Lights 1. Remove the headlight assembly 2. T wist the bulb socket 1/4 turn and remove. 3. Pull the bulb from the socket and replace. Front Sidemarker Light 1. Remove the screws and push-pins from the fr ont fender splash shield.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 12.5 Gallons 47.5 Liters Engine Oil 2.4 Liter T urbo Charged Engines 5.0 qts 4.8 Liters Cooling System * 2.4 Liter T urbo Charged Engines 8.1 qts 7.7 Liters * Includes heater and coolant recovery bottle filled to MAX level.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use Mobil 1 t 10W30 synthetic engine oil.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ...... 1 6 8 m Maintenance Schedule .................. 1 6 8 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9 Maintenance Schedules 9 section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9 B 9 .
At Each Oil Change • Change the engine oil filter . • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints and front suspension compo- nents. • Check the manual transaxle fluid level and fill plug condition. • Check the coolant level, hoses, and clamps.
SCHEDULE “B” Follow schedule “B” If you usually operate your vehicle under one or more of the following conditions. Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X Inspect the engine air cleaner filter . Replace as necessary .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Replace the engine air cleaner filter . X Replace the spark plugs.
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X Change the brake fluid. If vehicle is used for trailer towing.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Replace the engine air cleaner filter . X Replace the spark plugs and ignition cables.
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X Inspect the engine air cleaner filter and re- place as necessary .
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) Change engine oil and engine oil filter . XXXXX Inspect the brake linings. X Change the brake fluid. If vehicle is used for trailer towing. X Inspect the engine air cleaner filter and replace as necessary .
SCHEDULE “A” Miles 5,000 10,000 15,000 20,000 25,000 30,000 (Kilometers) (8 000) (16 000) (24 000) (32 000) (40 000) (48 000) [Months] [6] [12] [18] [24] Change engine oil and engine oil filter . X XXXXX Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 35,000 40,000 45,000 50,000 55,000 (Kilometers) (56 000) (64 000) (72 000) (80 000) (88 000) [Months] [30] [36] [42] Change engine oil and engine oil filter .
Miles 60,000 65,000 70,000 75,000 80,000 85,000 (Kilometers) (96 000) (104 000) (1 12 000) (120 000) (128 000) (136 000) [Months] [48] [54] [60] [66] Change engine oil and engine oil filter . X XXXX X Inspect the brake linings. X X Replace the engine air cleaner filter .
Miles 90,000 95,000 100,000 105,000 (Kilometers) (144 000) (156 000) (160 000) (168 000) [Months] [72] [78] [84] Change engine oil and engine oil filter . X X X X Inspect the brake linings. X Replace the engine air cleaner filter . X Replace the spark plugs.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 1 8 4 ▫ Prepar e For The Appointment ............ 1 8 4 ▫ Prepar e A List ........................ 1 8 4 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
• If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center .
Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs after your manufactur er’s new vehicle limited warranty expires. The manufactur er stands be- hind only the manufacturer’s Service Contracts.
MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Expr ess, and Discover orders ar e ac- cepted. If you prefer mailing your payment, please call for an order form.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway T raffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car .
T emperature Grades The temperature grades ar e A (highest), B, and C, repre- senting the tire’s r esistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
ABS (Anti-Lock Brake) System .............. 9 4 Adding Engine Coolant (Antifreeze) ......... 1 5 0 Adding Fuel ........................... 1 1 6 Air Cleaner , Engine ..................... 1 4 2 Air Conditioning ..................... 78,144 Air Conditioning Controls .
Catalytic Converter ..................... 1 4 1 CD Changer ......................... 72,73 CD Player ........................... 69,71 Center High Mounted Stop Light ........... 1 6 4 Chains, T ire ........................... 1 1 1 Changing A Flat T ire .
Downshifting ........................... 9 2 Drive Belts ............................ 1 4 0 Driving On Slippery Surfaces .................. 1 2 8 Electric Remote Mirrors ................... 4 8 Emergency , In Case of Jacking ..........................
Fuses ................................ 1 6 0 G a sC a p .............................. 1 1 6 Gasoline ............................. 1 6 5 Gasoline, Reformulated .................. 1 1 4 Gasoline/Oxygenate Blends ............... 1 1 4 Gauges Coolant T emperature .
Keyless Entry System ..................... 1 6 Keys .................................. 9 Lane Change and T urn Signals .............. 6 4 Lap/Shoulder Belts ...................... 2 0 Lead Free Gasoline ...................... 1 1 3 Leaks, Fluid ......
Maintenance Procedur es .................. 1 3 6 Maintenance Schedule Schedule 9 A 9 ......................... 1 7 8 Schedule 9 B 9 ......................... 1 7 1 Maintenance Schedules .................. 1 6 8 Malfunction Indicator Light ............
Power Door Locks .......................... 1 3 Steering .......................... 95,145 Steering, Checking .................... 1 4 5 W indows ............................ 1 9 Power Steering Fluid .................... 1 6 6 Pregnant W omen and Seat Belts .
Security Alarm ......................... 6 5 Sentry Key ............................. 9 Service Assistance ...................... 1 8 4 Service Contract ........................ 1 8 6 Service Manuals ........................ 1 8 8 Setting the Clock ..
Sizes ............................... 9 7 Snow T ires .......................... 1 1 1 Spinning ............................ 1 0 8 T read W ear Indicators .................. 1 0 9 T owing Disabled V ehicle ...................... 1 3 0 T ransaxle Manual .
An important point after buying a device Dodge 2004 Neon SRT4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dodge 2004 Neon SRT4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dodge 2004 Neon SRT4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dodge 2004 Neon SRT4 you will learn all the available features of the product, as well as information on its operation. The information that you get Dodge 2004 Neon SRT4 will certainly help you make a decision on the purchase.
If you already are a holder of Dodge 2004 Neon SRT4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dodge 2004 Neon SRT4.
However, one of the most important roles played by the user manual is to help in solving problems with Dodge 2004 Neon SRT4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dodge 2004 Neon SRT4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
