Instruction/ maintenance manual of the product DISH 351 Dish Network
Go to page of 12
Page 9 Chapter 2 Receiver Description and Inst allation The Receiver Front Panel Smart Card Door Behind this door is a slot for a future smart card. No smart card is included with this receiver . Up and Down Arrow Buttons The UP and DOWN buttons change the channel o n the receiver .
Page 10 Chapter 2 Receiver Description and Installation The Receiver Back Panel Connections T ighten the connections by hand only . If you use a wrench you might over -tighten the connectio ns and cause damage th at would not be covered b y the Limited W arranty .
Page 11 Remote Control T elephone Jack Connect a telephone cable with a st andard RJ-1 1 telephone connector to the receiver here, and then conn ect the cable to an active telephone line. Note : The receiver must be connected at all times to an active telephone li ne.
Page 12 Chapter 2 Receiver Description and Installation Remote Control Batteries The remote control comes with AAA batteries, which need to be installed when you first receive your system. When you replace old batteries, you shou ld replace all of the batteries.
Page 13 Remote Control Settings Remote Control Settings Change the Address The remote control and receiver can operate on any one of 16 addresses; however , they must both be on the same address for the remote to control the receiver . This section explains how to change the address in both devices.
Page 14 Chapter 2 Receiver Description and Installation Connecting Y our Receiver Connection Diagram Example The diagram below is an example of ho w to connect your rece iver , TV , and VCR. T ypical Connection Procedure T ighten all the coaxial cable conn ections only by hand.
Page 15 Performing the QAM Frequency Scan Performing the QAM Frequency Scan Note : When you turn your receiver o n it may display the QAM Frequency Scan and Signal S trength screen automatically . If it does, then skip down to Step 5. 1. Press the MENU button to open the Main Menu .
Page 16 Chapter 2 Receiver Description and Installation 3. Select the Inst allation option on the System Setup Menu . The Insta llation and Setup Menu screen is displayed. 4. Select the QAM Scan/Signal option. The QAM Fre- quency Scan and Signal S trength screen is displayed.
Page 17 Performing the QAM Frequency Scan 5. Select the Scan option. While scanning, the receiver displays the QAM Frequency Scan Progress screen. The scan can take a few minutes. Note : The receiver creates a table of available satellite transponders with the corresponding QAM frequencies.
Page 18 Chapter 2 Receiver Description and Installation Note : If the Results menu displays No T ransponders have been found , check your cable connections and re turn to step 5 to repeat the scan.
Page 19 Connecting Y our Receiver to a Phone Line Connecting Y our Rece iver to a Phone Line Yo u must keep your receiver connected to an active telephone line. Otherwise, you may not be able to ord er pay per vi ew programs or u se all of the DISH Interactive features.
Page 20 Chapter 2 Receiver Description and Installation Note : Usually , you need a telephone nu mber prefix only for business installations. For most residential inst allations, all you need to do is set the telephone system type. 6. Move the high light to the Out side Line Prefix list.
An important point after buying a device Dish Network DISH 351 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dish Network DISH 351 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dish Network DISH 351 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dish Network DISH 351 you will learn all the available features of the product, as well as information on its operation. The information that you get Dish Network DISH 351 will certainly help you make a decision on the purchase.
If you already are a holder of Dish Network DISH 351, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dish Network DISH 351.
However, one of the most important roles played by the user manual is to help in solving problems with Dish Network DISH 351. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dish Network DISH 351 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
