Instruction/ maintenance manual of the product s680 Directed Electronics
Go to page of 12
model s680.
2 © 2003 Directed Electronics, Inc T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Directed Studio neodymium component speaker system from Directed Electronics.
3 © 2003 Directed Electronics, Inc LIMITED TWO-YEAR CONSUMER W ARRANTY Directed Electronics, Inc. (DEI) promises to the original purchaser , to replace this product should it prove to be defective in.
4 © 2003 Directed Electronics, Inc Obtaining the highest quality sound reproduction in the mobile environment requires installation techniques and knowledge of vehicle interiors that go far beyond simple replacement of stock speakers.
5 © 2003 Directed Electronics, Inc INST ALLA TION PRECAUTIONS The Directed s680 neodymium separates are designed for installation into factory speaker locations, custom mounting enclosures or any flat mounting surface inside the vehicle with sufficient rear clearance.
6 © 2003 Directed Electronics, Inc FIGURE 1—WOOFER INST ALLA TION OPTIONAL 6x9 DRW-397 cut it to the proper size. If the hole is oversize, it is recommended that a spacer be built to compensate. 4. Pre-drill the holes for the mounting screws using a 1/8" drill bit.
7 © 2003 Directed Electronics, Inc TWEETER INST ALLA TION Review the Installation Precautions section of this guide before proceeding. Flush Mounting into Removed Panels 1. Disassemble the underside of the woofer mounting flange by removing the four screws from the bottom side of the tweeter bridge.
8 © 2003 Directed Electronics, Inc against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is the mounting screw hole. 4. Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet.
9 © 2003 Directed Electronics, Inc DRW-68 WIRING HARNESS FLUSH MOUNT TRIM RING TWEETER HEX HEAD BOL T FLUSH MOUNT HOUSING PANEL X-BRACKET TWEETER WIRE FIGURE 3—FLUSH MOUNTING MOUNTED P ANELS TWEETE.
10 © 2003 Directed Electronics, Inc FIGURE 6—CONNECTION/ADJUSTMENT SINGLE AMPLIFIER.
11 © 2003 Directed Electronics, Inc SPECIFICA TIONS Directed model 680 Frequency response 40 Hz - 21 kHz Power handling RMS 60 watts Power handling peak 120 watts Impedance 4 ohms Magnet weight 52.
12 © 2003 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available.
An important point after buying a device Directed Electronics s680 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Directed Electronics s680 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Directed Electronics s680 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Directed Electronics s680 you will learn all the available features of the product, as well as information on its operation. The information that you get Directed Electronics s680 will certainly help you make a decision on the purchase.
If you already are a holder of Directed Electronics s680, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Directed Electronics s680.
However, one of the most important roles played by the user manual is to help in solving problems with Directed Electronics s680. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Directed Electronics s680 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
