Instruction/ maintenance manual of the product G38106 Directed Electronics
Go to page of 11
Po w e r Class ® COMPONENT SPEAKER SYSTEM.
INTRODUCTION Thank you f or your purchase of this Po w e r Class ® Component Loudspeaker System from Precision P ower ™ . Our engineers hav e combined state of the ar t materials such as foamed prolyprop ylene cones and vapor-deposit titanium dome tweeters with cutting edge industrial design to achiev e competition-ready perf or mance lev els.
T OOLS OF THE TRADE Listed below are tools y ou ma y wish to hav e on hand bef ore star ting your installation. Ha ving the proper tools will make the installation much easier . Some of these tools are necessities , some will just make the job easier .
REAR DECK MOUNTING In rear deck installations , check the oper ation of the tr unk suspension springs or tension bars. These tension bars can mov e when opening and closing the trunk and can ex er t a great deal of f orce against anything that obstructs their mov ement, such as a speaker bask et or motor assembly .
Step 6 : Using the plastic grille ring as a template, mark the mounting holes with a pen. Step 7 : Pre-drill mounting holes using a 1/8" dr ill bit. W ARNING: Window mec hanisms and electrical wires and other expensive car parts have a nasty habit of hiding where y ou least expect.
5 NO TE: T o remove the trim ring fr om the tweeter housing: 1. Rotate the trim ring a few degrees in a c lockwise direction until y ou feel a detent. 2.
FLUSH MOUNTING INT O REMO VED P ANELS Step 1 : Deter mine the tweeter mounting location, then route the wires from the crossov er to the tweeter location. Step 2 : Mar k the center point of the tweeter location. Step 3 : If using a hole saw , first dr ill a pilot hole , then cut out the hole using a standard 2-1/8" hole saw .
FLUSH MOUNTING INT O MOUNTED P ANELS Step 1 : Deter mine the tweeter mounting location, then route the wires from the crossov er to the tweeter location. Step 2 : Mar k the center point of the tweeter location. Step 3 : If using a hole saw , first dr ill a pilot hole , then cut out the hole using a standard 2-1/8" hole saw .
Step 8 : Screw the bolts in until the tweeter housing is firmly mounted to the panel. (Make sure the arro w at the rear of the tweeter housing is pointing in the desired direction.
PC P ASSIVE CROSSO VER (CO VER REMO VED) SPECIFICA TIONS Model PC 525S PC 650S Nominal Impedance 4 ohms 4 ohms Po w e r Continuous/P eak 50/100 watts 60/120 watts F requency Response 90 Hz–20kHz 90 Hz–20kHz Sensitivity (2.
W arranty LIMITED TWO YEAR CONSUMER W ARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prov e to be defectiv e in workmanship or mater ial un.
An important point after buying a device Directed Electronics G38106 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Directed Electronics G38106 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Directed Electronics G38106 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Directed Electronics G38106 you will learn all the available features of the product, as well as information on its operation. The information that you get Directed Electronics G38106 will certainly help you make a decision on the purchase.
If you already are a holder of Directed Electronics G38106, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Directed Electronics G38106.
However, one of the most important roles played by the user manual is to help in solving problems with Directed Electronics G38106. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Directed Electronics G38106 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
