Instruction/ maintenance manual of the product WB15 Dimplex
Go to page of 13
AUTO-FILL WATER BOILERS INSTRUCTION MANUAL MODELS COVERED WB3 WB7 WB15 WB5E 1.
2 IMPORTANT HEALTH AND SAFETY INFORMATION PLEASE READ BEFORE USING YOUR NEW WATER BOILER Your new water boiler is designed to pr ovide a constant source of near boiling water for the preparation of hot drinks. THIS IS VERY HOT All personnel must be provided with suffi cient and appropriate training in the safe use of this appliance.
3 INTRODUCTION Your new water boiler is designed to give years of trouble free service provided that the instructions contained in this manual are followed carefully. Your new boiler is energy efficient, si mple to operate and easy to service. It is recommended that the installation is ca rried out by a properly qualified fitter.
4 WARNING: THIS APPLIANCE MUST BE EARTHED REAR ENTRY OF CABLE Fixed or flexible ca ble to be connected direct to t he terminal block, cable gland not utilised. BOTTOM ENTRY OF CABLE Use the cable gland. Loos en cable-gripping nut. Pass cable through gland, leaving enough free cable to connect into the terminal block.
5 BOTTOM ENTRY Connect to a suitable cold drinking water supply using 15mm copper pipe and push on the ‘T’ piece supplied. The ‘T’ has been blanked off using a brass plug. Leave this plug in place. Push the ‘T’ piece firmly onto the water inlet solenoid pipe with the brass plug facing forward.
6 OVERFLOW PIPE REAR ENTRY In your fitting kit you will find a straight push on connector wit h a small length of 15mm copper tube pushed into it. If rear entry has been chosen this connec tor must be replaced by a push on elbow (available from plum ber’s merchants).
7 OPERATION (All models except WB5E) After the electrical and water connecti ons have been made, switch the power and water supply on. The power and ready lights will flash once. The power light will then be constantly illuminated to indicate mains supply.
8 OPERATION (WB5Eonly) After the electrical and water connecti ons have been made, switch the power and water supply on. When the power supply is switched on, t he small indicator lamp on the front panel will glow orange. This means that t he water is filling to the bottom probe.
9 TECHNICAL SPECIFICATION ALL MODELS Tank constructed in stainless steel. Tank insulated from outer casi ng with high temper ature polystyrene. All boilers have electronic control of t he main functions. This means that the temperature is controlled precisely within given parameters.
10 DE-SCALING All m odels except WB5E To de-scale your machine, first disconnec t the machine from the power supply. Remove the case by removing the top and bottom screws hol ding the case to the wall bracket. Drain the remaining water through the drain plug in the bottom of the tank.
11 Clean the level sensing probes and their white holders completely using a clean non-metallic scourer. Ensure all traces of de-scaler are removed before using the boiler again. Rather than frequently de-scalin g the machine, it may be preferable to install an effective scale reducer or WRC appr oved food quality water softener.
12 SERVICE WARNING LIGHT (All Models except WB5E) All models except WB5E have this facility. This light is designed to help you discover the cause of any malfunction. If the circuit senses a problem, the service light will flash a number of times and then pause and repeat this sequence.
13 fallen to a point at which the heating element(s) could be damaged. If in order call service department on 01704 502911 Quoting the Serial Number 12 The machine has over-boiled and the level has fallen to a point at which the element(s) could be damaged.
An important point after buying a device Dimplex WB15 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dimplex WB15 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dimplex WB15 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dimplex WB15 you will learn all the available features of the product, as well as information on its operation. The information that you get Dimplex WB15 will certainly help you make a decision on the purchase.
If you already are a holder of Dimplex WB15, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dimplex WB15.
However, one of the most important roles played by the user manual is to help in solving problems with Dimplex WB15. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dimplex WB15 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
