Instruction/ maintenance manual of the product CU-7011 Denso
Go to page of 23
User's Manual.
Copyright © DENSO WAVE INCORPORATED, 2001 All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher.
i Pr eface Please READ through these operating instructions carefully. It will enable you to operate your CU-7011 correctly. After you have finished reading the instructions, keep this manual handy for speedy reference.
ii How this book is organized This manual is made up of 10 chapters and appendix. Chapter 1 Ethernet System Configuration Chapter 2 Functions of the CU-7011 Chapter 3 Components and Functions Chapter .
iii ■ Related Publications BHT-7000 User's Manual BHT-7000 User's Manual "LAN Support Version" BHT-100 Series User's Manuals BHT-100 Series User's Manual "LAN Supp.
iv Alerts you to those conditions which could cause serious bodily injury or death if the instructions are not followed correctly. W ARNING CAUTION Alerts you to those conditions which could cause minor bodily injury or substantial property damage if the instruc- tions are not followed correctly.
v • Avoid dropping the battery cartridge or letting it undergo any shock or impact. Doing so could cause the batteries to break, generate heat, rupture or burn. • Only use the dedicated charger (CU-7011, CU-7001, C-700 or C-750) for charging the battery cartridge.
vi Handling the battery cartridge • Never charge a wet or damp battery cartridge. Doing so could cause the batteries to break, generate heat, rupture, or burn. Handling the CU • Never put the CU in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight.
vii ■ Proper Care of the CU Before starting cleaning, unplug the AC adapter from the wall socket for safety. Clean the housing and the charge terminals of the CU and the battery cartridge termi- nals with a dry, soft cloth. • Never use benzene, alcohol, or other organic sol- vents.
Content Overviews Preface ................................................................................................................................. i How this book is organized ..................................................................
1 Chapter 1 Ethernet System Configu- ration Connecting CU-7011 units to an Ethernet enables you to use BHTs as a LAN client. For details about FTP and Socket API, refer to the BHT-BASIC Programmer's Manual. For procedures about setting the TCP/IP and FTP on the BHT, refer to the BHT User's Manual.
2 Chapter 3 Components and Functions Place the CU on a flat, horizontal plane. Do not install the CU on a wall or in a vertical position. LED indicators DATA (Communications LED, green) Lights when the BHT is communicating with the host computer. POWER (Power LED, green) Lights when the power is applied to the CU-7011.
3 Chapter 4 CU Status Indication by LED Indicators According to the ON/OFF states of the POWER and DATA LED indicators, you may check the machine status of the CU-7011 as listed below.
4 • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If foreign material or water gets into the CU, immediately unplug the AC adapter from the wall socket and contact your nearest dealer.
5 Chapter 6 Connecting to Ethernet 6.1 Setting the T ransmission Speed of the CU-701 1 Set the transmission speed of the CU-7011 to the same value as that of the BHT, by using the DIP switch provided on the bottom of the CU-7011. (1) Unplug the AC adapter from the wall socket.
6 6.2 Interface Cable Connection Connect the modular plug* of the Ethernet cable to the Ethernet port of the CU-7011. (*10Base-T 8-pin modular, RJ45, ITA/ETA category 3 or higher) Lock lever Ethernet cable •W hen connecting the modular plug, insert it until it snaps into place.
7 6.3 Communication with the Host Computer This section describes how to start communication with the host computer according to the FTP in System Mode. (1) Turn on the host computer. (2) On the host computer, start the FTP server program. (3) Turn on the BHT and run System Mode.
8 Chapter 7 Charging the Rechargeable Battery Cartridge You may charge the battery cartridge loaded in the BHT. Service Life of Rechargeable Battery Cartridge: Lithium-ion batteries used in the battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties, even under normal use.
9 Operator's Action Place the BHT on the CU-7011. ⇓ After approx. 6 hours ⇓ Remove the BHT. CU-7011 Status On standby ⇓ Normal charging ⇓ Charging completed ⇓ On standby Indicator LED on the BHT OFF ON (in red) ON (in green) OFF ■ Charging Operation and BHT's Indicator LED The charging time is approx.
10 Chapter 8 Displaying the CU System Information on the BHT You may display the CU-7011 system information on the BHT's LCD. Set the BHT on the CU-7011 and operate the BHT to display the SYSTEM INFORMA- TION screen on the LCD. From that screen, you may call up the system program version and MAC address.
11 Chapter 10 MAC Addr ess The MAC address of the CU-7011 is printed on the nameplate. Nameplate MAC address (example).
12 Appendix Specifications [ 1 ] Pr oduct Specifications Power Source -Europe 230 VAC, 16 VA -U.S. 120 VAC, 13 VA -Australia 10 to 18 VDC, 450 mA (on 12 VDC) Power Consumption 8 VA Dimensions 112 x 142 x 84 mm (W) x (L) x (H) (4.41 x 5.59 x 3.31 inches) Weight Approx.
Communication Unit CU-701 1 User's Manual First Edition, October 2001 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the handling and operating of the CU-7011.
An important point after buying a device Denso CU-7011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Denso CU-7011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Denso CU-7011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Denso CU-7011 you will learn all the available features of the product, as well as information on its operation. The information that you get Denso CU-7011 will certainly help you make a decision on the purchase.
If you already are a holder of Denso CU-7011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Denso CU-7011.
However, one of the most important roles played by the user manual is to help in solving problems with Denso CU-7011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Denso CU-7011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
