Instruction/ maintenance manual of the product SA150 Delta
Go to page of 12
INSTRUCTION MANUAL 1" Belt / 5" Disc Sander (Model SA150) P ART NO. 905593 - 05-31-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 13 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR BEL T / DISC SANDERS WARNING : F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions.
4 Fig. A Fig. B GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
6 BEL T SANDER T ABLE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Locate the M8x1.25x30mm hex head screw (A) Fig. 2, M8.4 flat washer (B), and table locking handle assembly (C), (D), (E) and (F). NOTE: The table locking assembly (C, D, E, and F) is shipped assembled.
7 ABRASIVE TO SANDING DISC 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove one-half of the abrasive backing (A) Fig. 7, to expose the adhesive. 3. Attach the lower section of the abrasive to the sanding disc (B), making sure that the abrasive edges fit the sanding disc edges exactly .
8 Fig. 15 Fig. 16 Fig. 17 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SANDER The switch (A) Fig. 15 is located on the top of the switch box. T o start the sander , move the switch forward to the “ON” position. T o stop the sander , move the switch back to the “OFF” position.
9 Fig. 22 Fig. 21 Fig. 20 Fig. 19 The disc table (C) can be tilted down 45 degrees (Fig. 21), by loosening the two wing nuts (one of which is shown at (B) Fig. 21). Tilt the table to the desired angle and tighten the two wing nuts. NOTE : The power take-off location is shown at (D) Fig.
10 Fig. 26 Fig. 23 Fig. 24 Fig. 25 CHANGING ABRASIVE BEL T 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove lock knob (A) Fig. 23, and remove side cover (B). 3. Depress tracking knob (C) Fig. 24, to r elease belt tension and remove belt (D) fr om the thr ee wheels (E), as shown.
11 Fig. 27 Fig. 28 MITER GAGE A miter gauge (A) Fig. 27, is supplied with your sander and can be used on the disc table. The miter gauge head (A) can be set up to 45 degrees right or left by loosening lock knob (B), moving miter gauge head to the desired angle and tightening lock knob (B).
12 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
An important point after buying a device Delta SA150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta SA150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta SA150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta SA150 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta SA150 will certainly help you make a decision on the purchase.
If you already are a holder of Delta SA150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta SA150.
However, one of the most important roles played by the user manual is to help in solving problems with Delta SA150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta SA150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
