Instruction/ maintenance manual of the product 900585 Delta
Go to page of 16
INSTRUCTION MANUAL 8" Drill Pr ess (Model 11-900) P ART NO. 900585 (011) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 1. DO NOT operate your drill press until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the operation of drill presses, obtain advice fr om your supervisor , instructor or other qualified person.
4 UNP ACKING Y our drill press is shipped complete in one container . Carefully unpack the drill pr ess and all loose items from the container . Figure 2 illustrates the drill press and all loose items supplied with the machine.
5 CLEANING Remove the protective coating fr om the machined surfaces of the drill press and all loose items. This coating may be removed with a soft cloth moistened with ker osene. DO NOT use acetone, gasoline, or lacquer thinner for this purpose. ASSEMBLING THE DRILL PRESS Fig.
6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 4. Place the drill press head (F) Fig. 7, onto the column (A) as far as it will go. Align head to table and base and tighten the two head locking screws (G) with wrench supplied. 5. Thread the three pinion shaft handles (H) Fig.
7 Use proper extension cor ds. Make sure your extension cord is in good condition. When using an extension cord, be sur e to use one heavy enough to carry the current to your tool. An undersized cor d will cause a drop in line voltage r esulting in loss of power and overheating.
8 Fig. 16 Fig. 17 GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER MOTOR SPECIFICA TIONS Y our drill press is wired for 110-120 volt, 60 HZ alternating current. Befor e connecting the machine to the power source, make sure the switch is in the “OFF” position.
9 Fig. 18 Fig. 19 Fig. 20 Fig. 21 ST AR TING AND STOPPING DRILL PRESS The switch (A) Fig. 18, is located on the front of the drill press head. T o turn the drill press “ON” move the switch to the up position. T o tur n the drill press “OFF” move the switch to the down position.
10 3. Fig. 22, illustrates the table alignment pin (B) removed. Loosen table locking bolt (D), tilt table to the desired angle and tighten bolt (D). When r etur ning table to the level position, replace table alignment pin (B). This will automatically position the table surface at 90 degrees to the spindle.
11 Fig. 27 CHANGING SPEEDS AND ADJUSTING BEL T TENSION NOTE: A BEL T POSITIONING SPEED CHART (E) FIG. 27, IS CONVENIENTL Y LOCA TED ON THE INSIDE TOP COVER OF THE DRILL PRESS. 1. Disconnect the drill press from the power sour ce. 2. Lift up the belt and pulley guard (A) Fig.
12 DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, the stop nuts on the threaded stop r od are used as follows: 1. Lower the spindle until the pointer (A) Fig. 28, lines up with the mark on the scale (B) you wish the depth to be.
13 1. Insert smooth end of drill bit (A) Fig. 30, as far as it will go into the chuck (B), or up to the flutes for small bits. 2. Make certain that the drill bit (A) Fig. 30, is centered in the chuck (B) before tightening the chuck with the key (C). 3.
14 BORING IN WOOD T wist drills, although intended for metal drilling, may also be used for boring holes in wood. However , machine spur bits are generally pr eferred for wood working; they cut a flat bottom hole and are designed for r emoval of wood chips.
15 NOTES.
16 Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory wh.
An important point after buying a device Delta 900585 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 900585 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 900585 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 900585 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 900585 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 900585, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 900585.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 900585. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 900585 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center