Instruction/ maintenance manual of the product 36-085 Delta
Go to page of 19
INSTRUCTION MANUAL 10" Dual Bevel Compound Power Miter Saw (Model 36-085) P ART NO. 901694 - 08-31-01 Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 19 T o learn more about DEL T A MACHINER Y visit our website at: www .
GENERAL SAFETY RULES W oodworking can be dangerous if safe and proper operating pr ocedures ar e not followed. As with all machinery , certain hazards ar e involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 3 ADDITIONAL SAFETY RULES FOR MITER SA WS 1. USE ONL Y CROSS-CUTTING SAW BLADES. When using carbide tipped blades, be certain that they have a neg- ative hook angle.
4 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
5 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the tool.
6 IMPORT ANT : DO NOT LIFT THE MITER SAW BY THE SWITCH HANDLE. THIS ACTION CAN CAUSE MIS- ALIGNMENT . AL WA YS LIFT THE MACHINE BY THE BASE OR CARR YING HANDLE .
7 Fig. 8 Fig. 9 Fig. 10 A B B C D E A TT ACHING STOCK STOP AND T ABLE EXTENSIONS 1. Decide on which side of the saw table you want the stock stop (A) Fig. 8, and attach the stock stop (A) on the table extension (B). 2. Insert the ends of table extension (B) Fig.
8 OPERA TING CONTROLS AND ADJUSTMENTS T ABLE HAZARD AREA WARNING: THE AREA INSIDE THE TWO RED LINES (A) FIG. 15 ON THE T ABLE IS DESIGNA TED AS A HAZARD ZONE. NEVER PLACE YOUR HANDS INSIDE THIS AREA WHILE OPERA TING THE TOOL. Fig. 15 A Fig. 13 F ASTENING MACHINE TO SUPPORTING SURF ACE Fig.
9 Fig. 17 Fig. 16 ST AR TING AND STOPPING THE MACHINE T o start the machine, squeeze the trigger (A) Fig. 16. T o stop the machine, release the trigger . This miter saw is equipped with an automatic electric blade brake. As soon as the trigger (A) Fig.
10 POINTER AND SCALE A pointer (B) Fig. 19 indicates the actual angle of cut. Each line on the scale (C) repr esents 1 degree. When the pointer is rotated fr om one line to the next on the scale, the angle of cut is changed by 1 degree. ADJUSTING POINTER T o adjust, loosen screw (D) Fig.
11 Fig. 22 Fig. 23 REAR SUPPOR T/CARR YING HANDLE A rear stabilizer bar (A) Fig. 22, is provided to pr event the miter saw from tipping to the r ear when the cuttinghead is returned to the up position after a cut has been made. For maximum support the bar (A) should be pulled out as far as possible.
12 Fig. 27 Fig. 28 ADJUSTING THE FENCE 90 DEGREES TO THE BLADE The fence (A) Fig. 27 should be adjusted so that it is 90 degrees to the blade. T o adjust: 1. DISCONNECT TOOL FROM POWER SOURCE . 2. First, adjust the blade so that it is parallel to the table slot.
13 2. Set the saw blade on the “0” degr ee positive miter stop. 3. Use one end of a squar e (A) Fig. 29 on the table and the other end against the blade. Check to see if the blade is 0 degrees to the table (Fig. 29). 4. If an adjustment is necessary , loosen the locknut (B) Fig.
TYPICAL OPERA TIONS AND HELPFUL HINTS 1. Before cutting, be certain that the cutting arm and table are at their corr ect settings and are firmly locked in place. Also, determine that the workpiece is the right size for the saw . 2. Firmly clamp the workpiece to the table against the fence.
15 Fig. 41 Fig. 42 CUTTING CROWN MOLDING One of the many features of a compound miter saw is the ease of cutting cr own molding. The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown molding.
2. Remove the scr ew (A) Fig. 45, and rotate the cover (B) to the rear (Fig. 46). 3. Depr ess the arbor lock (A) Fig. 47, to keep the blade from turning. 4. Use the supplied wr ench (D) Fig. 48 to loosen the arbor screw (E). T ur n it clockwise. 5. Remove the arbor scr ew (E), outside blade flange (F), and saw blade (G) from the saw arbor .
17 Fig. 49 Fig. 50 Fig. 51 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSHES, DISCONNECT THE TOOL FROM THE POWER SOURCE. Brush life varies, depending on the load on the motor . Check the brushes after the first 50 hours of use for a new machine, or after a new set of brushes has been installed.
18 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
36 36 36 36 36 The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC.
An important point after buying a device Delta 36-085 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 36-085 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 36-085 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 36-085 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 36-085 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 36-085, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 36-085.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 36-085. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 36-085 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
