Instruction/ maintenance manual of the product (Model 31-695) Delta
Go to page of 21
INSTRUCTION MANUAL P ART NO. 902122 - 02-20-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION.
4 ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 Fig. 2 1. Sander with 6" x 48" Sanding Belt and Backstop 2. Sanding Disc Plate 3. Belt and Pulley Cover 4. 9" Sanding Disc 5. Plug 6. T -Wrench 7. Drive Belt 8. M6 x 55mm Hex Socket Head Screws (2) 9. M6.4 Flat Washer (2 10. M6.4 Lockwasher (2) 11.
8 For your own safety , do not connect the machine to the power source until the machine is completely assembled and you read and understand the entir e instruction manual. ASSEMBL Y ST AND Any letter designations that are stamped on the braces of the stand are for pr oduction purposes ONL Y and are not used for assembling the stand.
9 BEL T AND PULLEY GUARD Place an M6.4 lockwasher and an M6.4 flat washer in that order on two M6 x 55mm hex socket head scr ews (B), and attach the belt and pulley guard (A) Fig. 8 to the machine. NOTE: Install the plug (C) in the guard. C SANDING DISC PLA TE 1.
10 Fig. 13 LOWER COVER FOR SANDING DISC Use three M4.2 x 13mm pan head scr ews (C) to attach the lower cover (A) Fig. 13 to the belt and pulley guard (B). Prevent the sanding disc fr om contacting the lower cover . Rotate the sanding disc by hand to ensure that no contact is made.
11 Fig. 17 LOCKING SWITCH IN THE “OFF” POSITION When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig.
12 Fig. 21 Fig. 22 ADJUSTING BACKSTOP SQUARE WITH SANDING BEL T 1. Before making this adjustment, check to see that the belt tension lever (A) Fig. 22 is all the way to the left in the “tighten” position. 2. Place a square (B) Fig. 23 on the sanding belt with the end of the square against the backstop.
13 SQUARING T ABLE WITH SANDING DISC 1. Place one end of a combination square (C) Fig. 25 on the table with the other end against the sanding disc. 2. If the table surface is not 90 degrees to the disc, loosen the table lock knob (A) Fig. 25, adjust the table, and tighten lock knob (A).
14 Fig. 30 Fig. 31 USING T ABLE ASSEMBL Y WITH SANDING BEL T Use the table assembly with the sanding belt in the vertical position ONL Y. T o move the table assembly (B) Fig. 30 to the sanding arm (A): 1. Remove the backstop (C) Fig. 30. 2. Loosen the screw (D) Fig.
15 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. Fig. 35 Fig. 36 WRENCH STORAGE A hole is provided in the stand for storing the hex wr ench (A) Fig. 35, supplied with the sander . REMOVING UPPER SANDING DRUM GUARD Y ou can remove the upper sanding drum guard (A) Fig.
16 Fig. 39 Fig. 40 5. Place a new 6" x 48" sanding belt (F) Fig. 40 over both sanding drums (G). Ensure that the belt will travel in the direction of the arr ows printed on the inside of the belt. 6. Move the tension lever (E) Fig. 39 left to the “TIGHTEN” position.
17 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the backstop (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt.
18 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and the accessory miter gauge (Fig. 48). Move the work from the center to the left side of the sanding disc. Always sand on the left (downward) side of the sanding disc.
19 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
An important point after buying a device Delta (Model 31-695) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta (Model 31-695) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta (Model 31-695) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta (Model 31-695) you will learn all the available features of the product, as well as information on its operation. The information that you get Delta (Model 31-695) will certainly help you make a decision on the purchase.
If you already are a holder of Delta (Model 31-695), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta (Model 31-695).
However, one of the most important roles played by the user manual is to help in solving problems with Delta (Model 31-695). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta (Model 31-695) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
