Instruction/ maintenance manual of the product T7600 Dell
Go to page of 73
Dell Precision Workstation T7600 Owner's Manual Regulatory Model: D02X Regulatory Type: D02X001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 Working on Your Computer ....................................................................................
Removing the Front I/O Panel and the USB 3.0 Ports ............................................................................................. 29 Installing the Front I/O Panel and the USB 3.0 Ports ..................................................
Error Messages ...................................................................................................................................................... 62 Errors That Halt Your Computer Completely ........................................
6.
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the Power Supply Unit (PSU) 1.
Removing the Front Cover NOTE: The front cover can be secured using the front panel-chassis lock. For more information the front-panel chassis lock, see Additional Information — Front Panel Chassis Lock. 1. Follow the procedures in Before Working Inside Your Computer .
Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the front cover. 3. Pull the clasp of the hard-drive bracket in an outward direction. 4. Slide the hard-drive bracket in an outward direction to remove it from the computer.
6. Slide the second hard-drive bracket in an outward direction to remove it from the computer. 7. Flex the hard-drive bracket on both sides to loosen the hard drive. 8. Lift the hard drive in an upward direction to remove it from the hard drive bracket.
9. If a 2.5 inch hard drive is installed , Push the retention clips in an outward direction and lift up the drive to remove it from the 3.5 inch hard-drive caddy. Installing the Hard Drive 1. Flex the hard drive-bracket and then insert the hard drive into the bracket.
3. Lift the cover upward to a 45–degree angle and remove it from the computer. Installing the Left Cover 1. Place the computer cover on the chassis. 2. Press down on the cover till it clicks into place. 3. Follow the procedures in After Working Inside Your Computer .
4. Push the intrusion switch downwards and remove it from the computer. Installing the Intrusion Switch 1. Install the intrusion switch into its place holder on the chassis. 2. Route the intrusion switch cable around the chassis clips and install the connector to the system board.
4. Press down the latch and pull the PCI card away from the computer. Installing the PCI Card 1. Push the expansion card into the card slot and secure the latch. 2. Install the plastic latch that secures the PCI card to the card slot. 3. Install the left cover.
4. Disconnect the power cable from the back of the optical drive. 5. Press down on the blue release tab to release the latches that secure the optical drive.
6. Slide the optical drive out of its compartment and lift it up to remove it from the computer. 7. Flex the optical drive bracket latches in an outward direction to loosen the optical drive from the bracket. 8. Lift the optical drive and remove it from the bracket.
Installing the 2.5-inch Optical Drive 1. Slide the optical drive into its compartment and ensure it is seated firmly. 2. Connect the power cable and the data cable to the back of the optical drive. 3. Install the left cover. 4. Follow the procedures in After Working Inside Your Computer .
5. Press down on the release latch on the air tunnel base and lift it upwards to remove it from the computer. 6. Repeat the steps to remove the second air tunnel module from the computer. Installing the Air Tunnel NOTE: The air tunnel is an optional component and your computer may not ship with it.
Removing the Processor/Memory's Slot Cover NOTE: The cover is an optional component and it covers the additional processor and the memory slots. Your computer may not be shipped with the cover. 1. Follow the procedures in Before Working Inside Your Computer .
3. Press down on the memory-securing clips on each side of the memory module, and lift the memory module upwards to remove it from the computer. Installing the Memory 1. Insert the memory module into the memory socket. 2. Press down on the memory module until the securing clips secure the memory in place.
4. Remove the captive screws that secure the heat sink. 5. Lift up the heat sink and remove it from the computer. 23.
Installing the Heat Sink 1. Place the heat sink inside the computer. 2. Tighten the captive screws to secure the heat sink to the system board. 3. Connect the heat-sink cable to the system board. 4. Install the left cover. 5. Follow the procedures in After Working Inside Your Computer .
Removing the System Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) left cover b) optical drive 3. Remove the screws that secure the optical-drive bracket. 4. Push the air duct in the direction indicated to unhinge it from the system fan module.
6. Slide the second air duct in the direction of the system fan to loosen it from its retention clasps. 7. Pull the second air duct in the direction opposite to the system fan module. 8. Lift the second air duct in an upwards direction to remove it from the computer.
9. Route the system fan cable through the opening in the system fan module. 10. Disconnect the system fan cable connectors from the system board. 11. Remove the screws that secure the system fan module to the chassis.
12. Disconnect the system-fan cable from the system fan module and remove the system fan module from the computer. 13. Remove the rubber tabs that secure the system fan , lift up the fan and remove it from the fan assembly. Installing the System Fan 1.
4. Connect the system fan cables to their connectors on the system board. 5. Route the system fan cables out of the opening in the system fan module in the direction of the system board. 6. Slide the larger air duct downwards into the retention tabs until it is secured to the system fan module.
6. Slide the opposite edge of the front I/O panel outward to disengage the I/O module from the chassis. 7. Remove the screws that secure the USB 3.0 module to the front I/O panel and remove it from the computer. 8. Remove the screws that secure the front I/O panel and remove it from the computer.
Installing the Front I/O Panel and the USB 3.0 Ports 1. Place the USB 3.0 module of the front I/O panel and install the screws to secure it in place. 2. Place the front I/O panel and install the screws to secure it in place. 3. Re-seat the front I/O panel assembly on the chassis and secure it to the chassis clips on both sides.
Installing the Power Switch 1. Connect the power switch cable to the system board. 2. Route the power switch module through the opening on the front panel. 3. Press the retention tab to secure the power switch in place. 4. Install the front cover. 5. Follow the procedures in After Working Inside Your Computer .
Installing the Speaker 1. Install the speaker and route the speaker cable through the chassis. 2. Connect the speaker cable to the system board. 3. Install the left cover. 4. Follow the procedures in After Working Inside Your Computer . Removing the Right Cover 1.
4. Lift the right cover at a 45–degree and remove it from the computer. Figure 1. Installing the Right Cover 1. Place the front cover on the computer. 2. Install the screws that secure the right cover to the computer. 3. Follow the procedures in After Working Inside Your Computer .
b) front cover 3. Disconnect the data and power cables from the back of the optical drive. 4. Press the release latch (1) and slide the optical drive outward to release it from the drive bay (2). 5. Remove the screws from the optical drive and remove the bracket.
a) front cover b) right cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Thermal Sensor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) left cover b) right cover c) air tunnel 3. Disconnect the thermal sensor cable from the system board and unroute it through the chassis clips.
Installing the Thermal Sensor 1. Install the thermal sensor cable on the system board. 2. Route the thermal sensor cable around the computer chassis. 3. Fasten the latch that secures the thermal sensor cable. 4. Install: a) air tunnel b) right cover c) left cover 5.
4. Repeat the above steps to remove the second processor (if available) from the computer. To verify if your computer has dual processor slots, see the System Board Components. Installing the Processor 1. Place the processor in its socket. 2. Replace the processor cover.
4. Route the cable from below the computer chassis as indicated. 5. Remove the screws that secure the hard drive fan to the front of the chassis and remove the fan from the computer.
Installing the Hard Drive Fan 1. Install the screws that secure the hard drive fan to the front of the chassis. 2. Route the hard drive fan cable through the chassis and connect it to its slot on the system board. 3. Install: a) PCI card b) left cover c) right cover 4.
Installing the Power Supply Unit (PSU) Card 1. Install the screws that secure the PSU card to the chassis. 2. Connect all the cables to the PSU card. 3. Install the right cover. 4. Follow the procedures in After Working Inside Your Computer . Removing the System Board 1.
4. Remove the screws that secure the system board to the chassis. 5. Lift the system board in an upward direction and remove it from the computer. 42.
Installing the System Board 1. Align the system board to the port connectors on the rear of the chassis and place the system board in the chassis. 2. Tighten the screws that secure the system board to the chassis. 3. Connect the connectors to the system board.
1. PCI slot 2. PCIe x16 slot 3. PCIe x16 slot (wired as x4) 4. PCIe x16 slot (accelerated graphics port) 5. PCIe open-ended slot (wired as x4) 6. USB 3.0 front panel connector 7. Intrusion switch connector 8. DIMM slots (available only when optional second processor is installed) 9.
3 Additional Information This section provides information for the additional features that are part of your computer. Memory Module Guidelines To ensure optimal performance of your computer, observe .
Power Supply Unit (PSU) Lock The PSU lock prevents the removal of the PSU from the chassis. NOTE: To lock or unlock the PSU, always ensure that the cover of the chassis is removed. For information on removing the left cover, see Removing the left cover.
4 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only.
Table 3. System Configuration Option Description Integrated NIC Allows you to configure the integrated network controller. The options are: • Disabled • Enabled (Default Setting) Integrated NIC 2 Allows you to configure the second integrated network controller.
Option Description SMART (Self Monitoring Analysis and Reporting Technology) specification. • Enable SMART Reporting - This option is disabled by default. PCI Bus Configuration Allows you to configure the PCI buses. The options are: • 64 PCI Buses (Default) Audio Allows you enable or disable the audio feature.
Option Description Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor. Default Setting: Enabled Cache Prefetch Default Setting: Enable Hardware Prefetch and Adjacent Cache Line Prefetch RMT Default Setting: Enabled Table 5.
Option Description Password Change Allows you to enable the disable permission to the System password when the admin password is set. Default Setting: Allow Non-Admin Password Changes is not selected TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST.
Option Description • Disabled (Default Setting) — Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. • LAN Only — Allows the system to be powered on by special LAN signals.
a) Enter the Service Tag or Express Service Code and click Submit . b) Click Submit and proceed to step 5. 4. If you do not have your computer's service tag or express service code, select one of.
– Only lower case letters are valid, upper case letters are not allowed. – Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (), (]), (`). Re-enter the system password when prompted. 4. Type the system password that you entered earlier and click OK .
6. Connect the computer to the electrical outlet and power-on the computer. 7. Power-off the computer and disconnect the power cable from the electrical outlet. 8. Remove the cover. 9. Replace the jumper on the pins. 10. Install the cover. 11. Follow the procedures in After Working Inside Your Computer .
5 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
58.
6 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Diagnostic LEDs NOTE: The diagnostic LEDs only serve as an indicator of the progress through the Power-On Self Test (POST) process.
installed, try moving it to a different DIMM connector and re-start the computer. • If available, install verified working memory of the same type into your computer. A possible graphics card failure has occurred. • Ensure that the display/ monitor is plugged into a discrete graphic card.
computer boots, add the peripheral cards back one by one until you find the bad one. • If the problem persists, the system board / system board component is faulty. A possible system board failure has occurred. • Disconnect all internal and external peripherals, and re- start the computer.
Error Messages There are three types of BIOS error messages that are displayed depending on the severity of the issue. They are: Errors That Halt Your Computer Completely These error messages will halt the computer requiring you to cycle the system's power.
Error Message Alert! Hard Drive fan1 failure. Alert! Hard Drive fan2 failure. Alert! Hard Drive fan3 failure. Alert! CPU 0 fan failure. Alert! CPU 1 fan failure. Alert! Memory related failure detected. Alert! Correctable memory error has been detected in memory slot DIMMx.
64.
7 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer.
Feature Specification T3600 2 GB T5600 / T7600 4 GB Maximum memory T3600 64 GB T5600 128 GB T7600 512 GB Table 18. Video Feature Specification Discrete (PCIe 3.
Feature Specification PCI 2.3 (32-bit, 33 MHz): 133 MB/s SAS – 3 Gbps SATA – 1.5 Gbps and 3.0 Gbps USB – 1.2 Mbps Low Speed, 12 Mbps Full Speed, 480 Mbps High Speed, 5 Gbps Super Speed Table 22. Drives Feature Specification T3600 /T5600 Externally accessible: Slimline SATA optical bays one 5.
Feature Specification Video Video card dependent • DVI connector • DisplayPort • DMS-59 Table 24. Internal Connectors Feature Specification System power one 28–pin connector System fans three .
Feature Specification Front panel audio HDA header one 2x5 pin connector HDD Back Panel : SATA T3600 four 7-pin SAS/SATA connectors T5600 one 36-pin mini-SAS connector, four 7-pin SAS/SATA connectors .
Feature Specification T3600 635 / 425 W (input voltage of 100 VAC – 240 VAC) T5600 825 / 635 W (input voltage of 100 VAC – 240 VAC) T7600 1000 W (input voltage 100 VAC – 107 VAC) 1300 W (input voltage 181 VAC – 240 VAC) 1100 W (input voltage 108 VAC – 180 VAC) Maximum heat dissipation 1300 W 4113.
Feature Specification Storage –40 °C to 65 °C (–40° F to 149 °F) Relative humidity (maximum) 20% to 80% (noncondensing) Maximum vibration: Operating 5 Hz to 350 Hz at 0.
72.
8 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
An important point after buying a device Dell T7600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dell T7600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dell T7600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dell T7600 you will learn all the available features of the product, as well as information on its operation. The information that you get Dell T7600 will certainly help you make a decision on the purchase.
If you already are a holder of Dell T7600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dell T7600.
However, one of the most important roles played by the user manual is to help in solving problems with Dell T7600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dell T7600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
