Instruction/ maintenance manual of the product D90DW Dell
Go to page of 18
Installation Guide Dell ® Wyse D Class Conversion to WES7 Wyse USB Firmware T ool TM Release 1.20 . 0 .1 Products: D10D , D50D , D90DW Issue: 040914 PN: 883887-38L Rev .
Copyright Notices © 2014 , Dell Inc. All Rights Reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in a retrieval.
Contents 1 Introduction 1 Kit Contents 1 Kit Warranty 2 Overview 2 Dell T echnical Support 2 Related Documentation and Services 2 Dell Online Community 2 2 Installing D Class Flash 3 Requirements 3 Pr.
iv Contents This page intentionally b lank..
1 Introduction This guide provides step-by-step instructions to use Wyse USB Firmware T ool to convert the following Wyse D class thin clients to WES7: • D10D (with minimum 2 GB RAM) • D50D (with .
2 Chapter 1 Kit Warranty The warranty on the hardware component of this kit assumes the remaining months of warranty of the thin client in which it is installed, or for 90 days, whichever is greater . Installation of this kit will not void the factory warranty, however the user will be responsible for damage due to improper installation.
2 Installing D Class Flash This chapter contains information for users of Wyse D class thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING : Flash modules may be susceptible to damage by Electro- Static Discharge (ESD).
4 Chapter 2 4. Place your thumbs on the top surface of the opposite end where the three screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover will shift approximate 1/4 inch to hang over the back panel.
Installing D Class Flash 5 Figure 5 Main board and Flash module 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining scr ew as shown in Figure 6. Lift the flash module out of the socket.
6 Chapter 2 This page intentionally b lank..
3 Installing WES7 Firmware This chapter includes the requirements and procedur es you need to install and use Wyse USB Firmware T ool to update your thin client to WES7 firmware. TIP : The purpose of the USB Firmware T ool is to configure a bootable USB key f or device firmware.
8 Chapter 3 Procedures IMPORT ANT : Complete the following procedures as an administrator (administrator privileges are required). Step 1: Copy the D Class WES7 Conversion Image Folder (on the DVD- RO.
Installing WES7 Firmware 9 Figure 8 Configuration options 3. Select the Configure the USB key to Copy/Pull or to Update/Push firmware option, and then click Next to open the Select the Configuration dialog box. Figure 9 Update firmware options - Windows Embedded Standard 7 4.
10 Chapter 3 Figure 10 Browse for image file 8. Click Browse . Figure 11 Browse to select commandsXml.xml 9. Navigate to the D Class WES7 Conversion Image folder (on your hard drive) that contains the commandsXml.
Installing WES7 Firmware 11 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recognize an inserted USB key), and then click Next . The pr ogress bars show the overall (formatting and configuration) progress and task progr ess.
12 Chapter 3 Step 5: V erifying Thin Client Operation After the thin client displays the WES7 desktop, you can verify the V ersion and that your general client information is correct. 1. On the General tab of the Wyse Client Information window ( Start > All Programs > Wyse Client Information ), verify the following: • V ersion is 9.
Installing WES7 Firmware 13 Step 7: Obtain a Firmware Update After converting your thin clients, obtain any available firmware update at http://www. wyse.com/serviceandsupport/support/downloads.asp . WARNING : Use of the Software on more than one device requires that you first purchase from Dell additional copies of, or licenses to, the Softwar e.
Installation Guide Dell ® Wyse D Class Conversion to WES7 Issue: 040914 Written and published by: Dell Inc., April 2014 Created using FrameMaker ® and Acr obat ®.
An important point after buying a device Dell D90DW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dell D90DW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dell D90DW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dell D90DW you will learn all the available features of the product, as well as information on its operation. The information that you get Dell D90DW will certainly help you make a decision on the purchase.
If you already are a holder of Dell D90DW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dell D90DW.
However, one of the most important roles played by the user manual is to help in solving problems with Dell D90DW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dell D90DW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
