Instruction/ maintenance manual of the product 5524P Dell
Go to page of 20
Dell PowerConnect 5500 Series Getting Started Guide Regulatory Models: PowerConnect 5524, 5524P , 5548, 5548P ContaxGS.book Page 1 Frid ay, August 20, 2010 1:53 PM.
Notes, Cautions, and W arnings NOTE: A NOTE indicates important in formation that helps you make better use of your system. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WAR NI NG : A WARNING indicates a potential for property damage, personal injury , or death.
Contents 3 Contents 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . 5 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Site Preparation . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking . . . . . . . . . . . . . . . .
4 Contents 3 Configuring the Switch . . . . . . . . . . . . . 13 Configuration Work Flow . . . . . . . . . . . . . . . . 13 Connecting the Switch to the T erminal . . . . . . . . . 14 Booting the Switch . . . . . . . . . . . . . . . . . . . . 15 Configuring the Stack .
Getting Started Guide 5 Installation Overview This guide describes how to install and run the P owerConnect 5500 series switches. F or more information, see the Dell P owerConnect 5500 Series User Guide , available on your Documentation CD, or check the Dell Support website at support.
6 Installation • Cabling — The cabling is routed to avoid sou rces of electrical noise, such as radio transmitters, broadcast ampl ifiers, power lines, and fluorescent lighting fixtures. • Ambient Requirements — The ambient unit operating temperatur e range is 0 to 45ºC (32 to 113ºF) at a re lative humidity of 10% to 90%, non- condensing.
Installation 7 Installing the Switch The P owerConnect 5500 Series switches can be: • Installed o n a rack • Placed on a flat surface Installing in a Rack CAUTION: Disconnect all cables from the unit before mounting the switch in a rack or cabinet.
8 Installation 3 Repeat the process for the rack-mountin g bracket on the other side of the switch. 4 Insert the unit into the 48.26-cm (19-inch) rack, ensuring that the rack-mounting holes on the switch l ine up to the mounting holes on the rack. 5 Secure the unit to the rack with the rack scr ews (not provided).
Getting Started Guide 9 Stacking Overview Each switch is a member in a stack, although the stack may consist of only a single switch. Up to eight switches are supported per stack. All stacks must have a Master unit, and may have a Master Backup unit. All other switches are connected to the stack as members (slaves).
10 Stacking F igur e 2-1 shows this process. Figure 2-1. Stacking Cable Diagram HDMI Ports F r o n t P a n e l HDMI Ports F r o n t P a n e l HDMI Ports F r o n t P a n e l F r o n t P a n e l HDMI Ports ContaxGS.
Stacking 11 Unit ID Assignment Each switch in the stack has a unique uni t ID that defines the unit’s position and function in the stack. F igur e 2-2 describes the stacking LEDs on the front panel of the switch.
12 Stacking Manual Assignment T o assign unit IDs to the switches in the stack, do the following for each switch in the stack: 1 Connect the switch to the terminal, as described in "Connecting the Switch to the T erminal". 2 T urn on the switch to begin auto boot and press Return or Esc to abort and enter the Start Up menu.
Getting Started Guide 13 Configuring the Switch This section describes the configuratio n that must be performed after the switch is installed and connected to power supplies. Additional advanced functions ar e described in the Dell P owerConnect 5500 Series User Guide on the Documentation CD.
14 Configuring the Switch Connecting the Switch to the T erminal The switch is configured and monitor ed through a terminal desktop system that runs terminal emulation software.
Configuring the Switch 15 Booting the Switch After the local terminal is connected, turn on power . The switch then goes through power -on self -test (POST). PO ST runs every time the switch is started and checks hardwar e componen ts, to determine if the switch is operational before completely booting.
16 Configuring the Switch Configuring the Stack The switch is always considered to be a stack of switches even if the stack only contains a single switch. If there is mo r e than one switch in the stack, each switch must be configured individual ly . See "Unit ID Assignment" for instructions on how to configure the stack.
Configuring the Switch 17 • The IP addr ess to be assigned to the VLAN 1 interface through which the switch is to be managed (by d efault, every external and internal port is a member of the VLAN 1).
18 Configuring the Switch To manage the switch usin g SNMP (required for Dell Network Manager) you can: • Setup the initial SNMP version 2 account now. • Return later and set up the SNMP version account. For more information on setting up a SNMP version 2 account, see the user documentation.
Configuring the Switch 19 7 Set up user account privilege level, as follows: The following information is displayed: Now we need to set up y our initial privilege (Level 15) user account. Th is account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later.
20 Configuring the Switch 11 P ress Enter . The following information is displayed: Finally, set up t he default gateway. Please enter the IP address of the gateway from which this network is reachable (e.g. 192.168.2.1).D efault gateway (A.B.C.D):[0.
An important point after buying a device Dell 5524P (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dell 5524P yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dell 5524P - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dell 5524P you will learn all the available features of the product, as well as information on its operation. The information that you get Dell 5524P will certainly help you make a decision on the purchase.
If you already are a holder of Dell 5524P, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dell 5524P.
However, one of the most important roles played by the user manual is to help in solving problems with Dell 5524P. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dell 5524P along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
