Instruction/ maintenance manual of the product 3030 Dell
Go to page of 49
OptiPlex 3030 All-in-One Owner's Manual Regulatory Model: W10B Regulatory Type: W10B001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer................................................................................ 5 Before Working Inside Your Computer ................................................................................................ 5 Recommended Tools .
Removing the Camera ........................................................................................................................ 29 Installing the Camera .....................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 3. Disconnect all network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets.
2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. . 2. Ensure that the computer and all attached devices are turned off.
2 System Overview Figure 1. Inside View – 1 1. memory shield 2. system board shield 3. bottom cover 4. power-switch board 5. hard drive 6. VESA Bracket 7.
Figure 2. Inside View – 2 1. WLAN card 2. memory module 3. power supply unit 4. system board 5. speaker 6. display bracket 7. system fan 8. heatsink 9. camera 10. microphone System Board Layout The following image displays the system board layout of the computer.
1. SD Memory card reader 2. memory module 3. speaker connector 4. touch connector 5. control board connector 6. HDD connector 7. ODD connector 8. SATA power connector 9. convertor board connector 10. power connector 2 11. power connector 1 12. system fan connector 13.
3 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Stand 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the stand cover.
b. Remove the back cover from the computer [2]. Installing the Back Cover 1. Place the back cover on the computer. 2. Press at the corners of the back cover to secure it to the computer. 3. Install: a. stand b. stand cover 4. Follow the procedures in After Working Inside Your Computer .
Installing the Optical Drive 1. Slide the optical drive to the computer and tighten the screw to secure it. 2. Install: a. back cover b. stand c. stand cover 3. Follow the procedures in After Working Inside Your Computer . Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer .
4. Slide and remove it to access the hard-drive cable. 5. Disconnect the hard-drive cable from the hard drive, and remove it from the computer. 6. Pry the hard-drive bracket apart to release the hard drive. Remove the hard drive from the hard-drive bracket.
Installing the Hard Drive 1. Insert the hard drive into the hard-drive bracket. 2. Connect the hard-drive cable to the hard drive and align the hard drive to its slot on the computer. 3. Install: a. back cover b. stand c. stand cover 4. Follow the procedures in After Working Inside Your Computer .
Installing the Convertor Board 1. Tighten the screws to secure the convertor board to the computer. Connect the cables to the convertor board. 2. Install: a. back cover b. stand c. stand cover 3. Follow the procedures in After Working Inside Your Computer .
4. Pry the retention clips away from the memory module until it pops up. Lift and remove the memory module from its connector. Installing the Memory 1. Align the notch on the memory-card with the tab in the system-board connector. 2. Press down on the memory module until the release tabs spring back to secure them in place.
Installing the System-Board Shield 1. Align the system-board shield on the system board. Tighten the screws to secure it to the computer. 2. Install: a. back cover b. stand c. stand cover 3. Follow the procedures in After Working Inside Your Computer .
Installing the Heatsink 1. Align the heatsink on the system board. Tighten the screws to secure it to the computer. 2. Install: a. system-board shield b. back cover c. stand d. stand cover 3. Follow the procedures in After Working Inside Your Computer .
4. Remove the speaker cover from the computer. 5. Perform the following steps as shown in the illustration: a. Disconnect the speaker cable from the system board [1].
6. Perform the following steps as shown in the illustration: a. Remove the screws that secure the speakers to the computer [1]. b. Remove the speakers from the computer [2]. Installing the Speakers 1. Align the speakers on the computer. Tighten the screws to secure them to the computer.
b. back cover c. stand d. stand cover 5. Follow the procedures in After Working Inside Your Computer . Removing the VESA Bracket 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. stand cover b. stand c. back cover 3. Perform the following steps as shown in the illustration: a.
a. stand cover b. stand c. back cover d. System-board shield e. VESA bracket 3. Perform the following steps as shown in the illustration: a. Disconnect the system-fan cable from the system board [1]. b. Remove the screws that secure the system fan [2].
4. Disconnect the power-switch cable from the power-switch board to remove it from the computer. Installing the Power-Switch Board 1. Insert the power-switch board into its slot on the computer and fix the tape to secure it. Connect the power-switch cable to the power-switch board.
c. back cover d. memory e. VESA bracket f. system-board shield g. heatsink h. WLAN card 3. Disconnect the following from the system board: a. camera cable b. LVDS cable c. system-fan cable d. optical-drive cable e. hard-drive cable f. hard-drive/optical-drive power cable g.
5. Remove the system board from the computer. Installing the System Board 1. Align the system board on the computer. 2. Tighten the screws to secure the system board to the computer. 3. Connect the following cables to the system board: a. camera cable b.
f. hard-drive/optical-drive power cable g. convertor-board cable h. touch cable (if available) i. power-switch cable j. speaker cable 4. Install: a. WLAN card b. heatsink c. system-board shield d. VESA bracket e. memory f. back cover g. stand h. stand cover 5.
4. Remove the screws that secure the display bracket to the computer. Lift and remove the display bracket from the computer. Installing the Display Bracket 1. Align the display bracket on the computer. 2. Tighten the screws to secure the display bracket to the computer.
d. system fan e. heatsink f. speakers g. system-board shield h. VESA bracket i. memory j. hard drive k. optical drive l. back cover m. stand n. stand cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Camera 1. Follow the procedures in Before Working Inside Your Computer .
4. Disconnect the camera cable from the camera and remove the camera from the computer. Installing the Camera 1. Connect the camera cable to the camera. 2. Align the camera into its slot and tighten the screws to secure it to the computer. 3. Install: a.
a. Remove the screw that secures the microphone. b. Disconnect the microphone cable from the microphone. c. Remove the microphone from the computer. Installing the Microphone 1. Connect the microphone cable to the microphone. 2. Align the microphone into its slot and tighten the screws to secure it to the computer.
4 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field. Down arrow Moves to the next field. <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable.
Option Description • Enabled Legacy Options ROMs (Default: Enabled) Date/Time Allows you to set the date and time. The changes to the system date and time takes effect immediately. Table 3. System Configuration Option Description Integrated NIC Allows you to configure the integrated network controller.
Option Description Default Setting: All devices are enabled. Audio Allows you enable or disable the audio feature. • Enable Audio – Enable Microphone – Enable Internal Speaker Default Setting: All devices are enabled. OSD Button Management Allows you to disable the OSD (On-Screen Display) buttons.
Option Description • Confirm the new password Strong Password Enable strong password - This option is disabled by default. Password Configuration This field controls the minimum and maximum number of characters allowed for the admin and system passwords.
Table 5. Secure Boot Option Description Secure Boot Enable Allows you to enable or disable the Secure Boot Feature. The options are: • Disabled (Default) • Enabled Expert Key Management Allows you to manipulate the security key databases only if the system is in Custom Mode.
Option Description Limit CPUID Value This field limits the maximum value the processor Standard CPUID Function will support • Enable CPUID Limit (Disabled by default) NOTE: Some Operating system wil.
Option Description • LAN Only • WLAN only • LAN with PXE Boot This option is Disabled by default. Block Sleep Allows you to block entering to sleep (S3 state) in OS Environment. • Block Sleep (S3 State) This option is disabled by default. Intel Smart Connect Technology The option is disabled by default.
Table 11. Maintenance Option Description Service Tag Displays the service tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. SERR Messages Controls the SERR message mechanism.
Option Description NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer and when Client DHCP is set to Static IP . Client SubnetMask Displays the subnet mask of the client.
6. Select your computer model and the Product Support page of your computer appears. 7. Click Get drivers and click View All Drivers . The Drivers and Downloads page opens. 8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS .
• Only lower case letters are valid, upper case letters are not allowed. • Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (), (]), (`). Re-enter the system password when prompted. 4. Type the system password that you entered earlier and click OK .
5 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view information about your computer.
Feature Specification Discrete 1 GB DDR3 Table 17. Audio Feature Specification Controller ALC3661-CG (Realtek) Speaker single 4-ohms, 2 W AVG speakers with 2.
Table 21. Drives Feature Specification Hard drive one 2.5-inch SATA drive Optical drive (optional) one DVD-ROM, DVD+/- RW Table 22. Ports and Connectors Feature Specification Audio: one universal audio jack/Line-out port Network adapter one RJ45 connector USB 2.
Table 24. Camera (optional) Feature Specification Image resolution 0.92 megapixel Video resolution 720p @ 30 FPS HD Diagonal viewing angle 74 degrees Table 25. Stand Feature Specification Tilt –5 degrees to 30 degrees Table 26. Physical Dimensions Feature Without Stand With Stand Width 489.
Feature Specification Back panel: Link integrity light on integrated network adapter : Green — a good 10 Mbps connection exists between the network and the computer. Green— a good 100 Mbps connection exists between the network and the computer. Orange — a good 1000 Mbps connection exists between the network and the computer.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
An important point after buying a device Dell 3030 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dell 3030 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dell 3030 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dell 3030 you will learn all the available features of the product, as well as information on its operation. The information that you get Dell 3030 will certainly help you make a decision on the purchase.
If you already are a holder of Dell 3030, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dell 3030.
However, one of the most important roles played by the user manual is to help in solving problems with Dell 3030. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dell 3030 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
